comfortel 1000E User manual
#1000E BASIN BENCH KIT - STANDARD WHITE BASIN
#1000F BASIN BENCH KIT - STANDARD BLACK BASIN
standard basin
bench kit
owners manual
help.comfortel.com.au
DESIGNING YOUR OWN BASIN BENCH: FOLLOW THESE GUIDELINES
BENCH FRAME INSTALLATION
Please follow these measurements for installing the Comfortel Bench Kit Basin. Comfortel do not recommend that the
cut out for the basin bench frame is done, until after you receive the bench frame.
CUTTING A HOLE FOR
THE BASIN BENCH
KIT FRAME
INSTALLING BENCH KIT FRAME
REQUIRED (NOT SUPPLIED)
4X40MM STAINLESS STEEL BOLTS WITH SPRING WASHERS
WASH SIDE
CHAIR SIDE
BASIN BENCH HEIGHT
For use with Comfortel standard
basin chairs, we recommend the
height to the top of the bench to
be 650mm from the floor.
Recommended depth is 400mm
If you choose to design your own basin bench, Comfortel recommends that you follow these guidelines for the
best outcome to work with your chair and basin.
Comfortel are not liable if you change our recommendations below.
Please note. It is essential
that the cut out be as close as
possible to edge of the bench
nearest the chair as shown in
this diagram of 20mm.
4 POSITION
Based on a 700mm
Wide Washlounge
3 POSITION
Based on a 700mm
Wide Washlounge
2 POSITION
Based on a 700mm
Wide Washlounge
242
225
35
35 330
161 85
400
CUT OUT DETAIL
DRILL 4 HOLES
7
400 400800800
2400
242
225
35
35 330
161 85
CUT OUT DETAIL
DRILL 4 HOLES
7
400 400800800
4800
400
400 400800800
RECOMMENDED POSITIONING EXAMPLES
All measurements are in mm.
242
225
35
35 330
161 85
400
CUT OUT DETAIL
DRILL 4 HOLES
7
400 400800 400 400 800
3200
242
225
35
35 330
161 85
400
CUT OUT DETAIL
DRILL 4 HOLES
7
400 400800
1600
INSTALLATION & ASSEMBLY: OPTIONAL CHAIR TO BASIN BENCH
28 Connector
28
O7
305
150
INSTALL CHAIR TO BASIN BENCH
• Fix Connector to Bench front using two bolts and
nuts provided. Refer to sketch for drilling details.
• It is recommended to install these brackets before
installing bench for easy access.
DIAGRAM I
A periodic inspection of all
components and fasteners should be
made to ensure that your Comfortel
Product is structurally intact and
functioning properly.
Damaged and broken parts should
be replaced and loose fasteners
tightened.
All maintenance to be carried out by
a suitably qualified tradesperson.
UPHOLSTERY
All upholstery needs some care; good housekeeping will help to prolong
the life of any upholstered products. Avoid extreme temperatures.
Extreme cold can make your vinyl prone to cracking, while extreme heat
can cause permanent stretching. Avoid exposing your products to direct
sunlight for prolonged periods of time.
ALWAYS FOLLOW THE CLEANING INSTRUCTIONS
• Wipe with a clean colourfast cloth dampened with mild alkaline free
soap and luke warm water. Do not wet excessively.
• Remove all traces of any cleaning product by wiping with fresh water
and a clean cloth.
• Dry with a soft, clean cloth.
• Stubborn grime may require gentle scrubbing with a soft brush.
Do not use:
• hot or boiling water
• hydrocarbons including alcohol
• acetone
• furniture polishes
• bleach
• concentrated detergents
• abrasive powder or paste cleaners
• steel wool
• silicon or petroleum-based cleaners
• solvent based or abrasive cleaning agents
CLEANINGMAINTENANCE
HOW TO CHANGE A SHOWERHEAD
For more support & help,including
troubleshooting videos, refer to our
support center on our website
www.comfortel.com.au/service-
support/troubleshooting-videos/
GENERAL SAFETY
1. Read carefully and keep these instructions in a
safe place.
2. Use this product only for its intended function and
do not use attachments not recommended by the
manufacturer.
3. Do not use outdoors.
IMPORTANT PLEASE READ THESE SAFETY INSTRUCTIONS
ALL PLUMBING MUST BE COMPLETED
BY A LICENSED PLUMBER
IMPORTANT
INSTALLATION & ASSEMBLY: BASIN
BENCH FIXING DETAIL
1. Position Bench as required.
2. Bench must be secured to the floor, or wall.
(Fasteners not provided)
3. Seal base – seal the base of the bench inside and outside
with silicone.
BASIN ASSEMBLY
4. Install Flick Mixer using the O-ring, plastic and metal
washers & Long Nut, and Showerhead using the
Showerhose Basin Collar, O-ring, Foam Washer and
Plastic Nut as indicated.
5. Place Flick Mixer and Showerhead Hoses through the
holes in the Vinyl Strap.
6. Connect Flexible Waste Pipe to Plug and Waste which is
already installed making use of end with Flat Seal and
fitted flange.
BENCH KIT ASSEMBLY
7. Using 4x40mm Stainless Steel bolts with spring washers
and nuts (not supplied) fix Bench Kit Frame to top of Bench.
8. Connect hot and cold (½” connection) water braided
hoses to respective supplies.
9. Connect Flexible Waste Pipe (supplied) to P Trap (not
supplied) making use of Seal and Flange.
10. Connect Basin Spring which is already connected to the
tilt and slide plate to the hole in the Bench Kit Frame at
the front left corner.
11. Place both ends of Vinyl Cover into the slots provided on
front and back of Bench Kit Frame.
1Flick Mixer
2Showerhead
3Showerhose Basin Collar
4Comfortneck
5Foam Washer
6Plastic Nut
7Showerhead hose
8Vinyl Strap
9Flat seal
10 Flexible Waste Pipe
11 Fitted flange
12 Flange
13 Seal
14 Long nut
15 Plastic & Metal Washers
16 O-ring
17 O-ring
18 Basin spring
19 Bench Kit Frame
Comfortel Furniture Pty Ltd ABN 60 300 719 042
www.comfortel.com.au
Victoria (Head Office)
39-41 Nelson Street
Moorabbin VIC 3189
T 03 9553 5504
F 03 9553 5516
New Zealand
Comfortel Furniture Ltd
128a Hugo Johnston Drive
Penrose Auckland NZ
T 09 525 3357
F 09 525 3355
New South Wales
64 Hotham Parade
Artarmon NSW 2064
Ph: 02 9966 5900
Fax: 02 9966 5955
Queensland
18/6 Maunder Street
Slacks Creek QLD 4127
T 07 3209 1444
F 07 3209 1666
Western Australia
2/25 Catherine Street
Bentley WA 6102
T 08 9258 4446
F 08 9258 6601
South Australia
2A West Thebarton Road
Thebarton SA 5031
T 08 8443 3703
F 08 8443 3702
BASIN ASSEMBLY
2
7
8
10
11
9
12
13
5 6
3
4
1
17
16
15
14
19
18
#1000E BENCH KIT WHITE BASIN
#1000F BENCH KIT BLACK BASIN
PURCHASE DATE INVOICE NUMBER
NOTE YOUR PURCHASE DATE & INVOICE NUMBER FOR FUTURE REFERENCE
PRODUCT CODE The information contained in this document is subject to change without notice and
should not be construed as a commitment by Comfortel Furniture Pty Ltd.
Comfortel Furniture Pty Ltd. assumes no responsibility for any errors that may appear in
this document nor does it make expressed or implied warranty of any kind with regard
to this material, including, but not limited to, the implied warranties of merchantability
and fitness for a particular purpose.
Comfortel Furniture Pty Ltd. shall not be liable for incidental or consequential damages
in connection with or arising out of the use of this document and the program material.
PLEASE RETAIN THIS INFORMATION FOR FUTURE REFERENCE
For more information about our products and services, contact us at comfortel.com.au
help.comfortel.com.au
©Comfortel Furniture. All rights are reserved. No part
of this document may be photocopied, reproduced or
translated to another language without written consent
of Comfortel Furniture Pty Ltd.
WARRANTY PERIOD
TERMS AND CONDITIONS. For more information about our warranty, please refer to our website.
Revision Date: V2.11.08..2020
This manual suits for next models
1
Table of contents
Other comfortel Bathroom Fixture manuals
