Code Code Reader 1000 User manual

C005905_04_CR1000_User_Manual

C005905_04_CR1000_UserManual

User Manual

Code Reader™ 1000

Manual Version 04

Release Date: January 2013

C005905_04_CR1000_User_Manual

Statement of Agency Compliance

Code voids product warranty if the hard case has been opened or tampered with in any way.

In addion, a CB Test Cercate has been issued by the Naonal Cercaon Board (NCB) indicang CR1000

meets all safety and quality standards in accordance to IEC 60950-1:2001, First Edion.

The Code Reader™ 1000 (CR1000) has been tested for compliance with FCC regulaons and was found to be

compliant with all applicable FCC Rules and Regulaons.

IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, this device must not be

co-located or operate in conjuncon with any other antenna or transmier.

CAUTION: Changes or modicaons not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

The Code Reader 1000 has been tested for compliance to CE standards and guidelines and was found to conform

to applicable CE standards, specically the EMC requirements EN 55024, ESD EN 61000-4-2, Radiated RF Immunity

EN 61000-4-3, ENV 50204, EFT EN 61000-4-4, Conducted RF Immunity EN 61000-4-6, EN 55022, Class B Radiated

Emissions, and Class B Conducted Emissions.

C005905_04_CR1000_User_Manual

Code Reader™ 1000 User Manual

The soware described in this manual may only be used in accordance with the terms of its license agreement.

No part of this publicaon may be reproduced in any form or by any means without wrien permission from Code Corporaon. This

includes electronic or mechanical means such as photocopying or recording in informaon storage and retrieval systems.

NO WARRANTY. This technical documentaon is provided AS-IS. Further, the documentaon does not represent a commitment

on the part of Code Corporaon. Code Corporaon does not warrant that it is accurate, complete or error free. Any use of the

technical documentaon is at the risk of the user. Code Corporaon reserves the right to make changes in specicaons and

other informaon contained in this document without prior noce, and the reader should in all cases consult Code Corporaon

to determine whether any such changes have been made. Code Corporaon shall not be liable for technical or editorial errors or

omissions contained herein; nor for incidental or consequenal damages resulng from the furnishing, performance, or use of this

material. Code Corporaon does not assume any product liability arising out of or in connecon with the applicaon or use of any

product or applicaon described herein.

NO LICENSE. No license is granted, either by implicaon, estoppel, or otherwise under any intellectual property rights of Code

Corporaon. Any use of hardware, soware and/or technology of Code Corporaon is governed by its own agreement.

The following are trademarks or registered trademarks of Code Corporaon:

CodeXML®, Maker, QuickMaker, CodeXML® Maker, CodeXML® Maker Pro, CodeXML® Router, CodeXML® Client SDK, CodeXML®

Filter, HyperPage, CodeTrack, GoCard, GoWeb, ShortCode, GoCode®, Code Router, QuickConnect Codes, Rule Runner®, Cortex®,

CortexRM, CortexMobile, Code, Code Reader, CortexAG, CortexStudio, CortexTools, Anity®, and CortexDecoder.

All other product names menoned in this manual may be trademarks of their respecve companies and are hereby acknowledged.

The soware and/or products of Code Corporaon include invenons that are patented or that are the subject of patents pending.

U.S. Patents: 6997387, 6957769, 7428981, 6619547, 6736320, 7392933, 7014113, 7240831, 7353999, 7519239, 7204417, 6942152,

7070091, 7097099, 7621453, 8001550, 8011584

The Code Reader soware uses the Mozilla SpiderMonkey JavaScript engine, which is distributed under the terms of the Mozilla

Public License Version 1.1.

The Code Reader soware is based in part on the work of the Independent JPEG Group.

Code Corporaon, 14870 South Pony Express Road, Suite 200, Bludale, UT 84065

www.codecorp.com

C005905_04_CR1000_User_Manual

Table of Contents

1.0 - Unpacking............................................................................................................................................................... 1

2.0 - Aaching/Detaching a Cable................................................................................................................................... 1

3.0 - Powering the Reader On/O................................................................................................................................... 1

4.0 - Using a CR1000 Out of a Stand................................................................................................................................ 2

5.0 - Using a CR1000 in a Stand....................................................................................................................................... 2

6.0 - Reading Range ........................................................................................................................................................ 3

7.0 - Reader Feedback .................................................................................................................................................... 3

8.0 - Symbologies Defaulted On...................................................................................................................................... 4

9.0 - Symbologies Defaulted O...................................................................................................................................... 4

10.0 - Locang the Hardware Revision Number .............................................................................................................. 4

11.0 - Reader ID & Firmware Version .............................................................................................................................. 5

12.0 - Hole Mounng Paern.......................................................................................................................................... 6

13.0 - CR1000 Overall Dimensions .................................................................................................................................. 6

14.0 - USB Cable Example with Pinouts........................................................................................................................... 7

15.0 - RS232 Cable Example with Pinouts ....................................................................................................................... 7

16.0 - Reader Pinouts ..................................................................................................................................................... 8

17.0 - Maintenance.........................................................................................................................................................8

18.0 - Warranty .............................................................................................................................................................. 9

C005905_04_CR1000_User_Manual

3.0 - Aaching Cable and Powering On/O the Reader

1.0 - Unpacking

Remove the CR1000 from its packing and inspect it for damage. If the reader was damaged during shipping, please call Code at

(801) 495-2200.

Depending on the kit ordered, a USB or RS232 Anity® cable has been included with your reader.

USB Anity® Cable RS232 Anity® Cable

w/ Power Supply

For USB Cable: plug the USB end of the Anity® cable into a USB port on the host device. Aer several seconds, the reader will beep

twice, the LED will turn o and the CR1000 is ready for use.

For RS232 Cable: plug the power supply into the AC outlet, plug the power supply cord into the barrel jack of the cable, and connect

the RS232 connector to the appropriate serial port on the host device. Aer several seconds, the reader will beep twice, the LED will

turn o and the CR1000 is ready for use.

To aach a cable, plug the RJ-50 end of the Anity® cable into boom of the reader (Figure 1). Firmly push the connector into the

reader, unl a snap can be heard to indicate the cable is properly aached. To detach a cable, press a paper clip into the hole on the

back of the CR1000 (Figure 2), and gently pull the cable from the reader.

2.0 - Aaching and Detaching a Cable

Figure 1 Figure 2

C005905_04_CR1000_User_Manual

4.0 - Using a CR1000 Out of a Universal Stand

5.0 - Using a CR1000 in a Universal Stand

Revision 3 Hardware of the CR1000 has a stand detecon feature. By default, when the

CR1000 is placed in the stand, the reader will enter into moon detecon mode. When

in this mode, simply place a bar code in the scan eld to acvate the reader. The CR1000

will beep and ash a green LED to indicate a ‘good read’ has occurred.

When the CR1000 is removed from the stand, the reader switches to manual mode and

the buon must be pressed to read a bar code (refer to Secon 4.0).

Revisions 1 and 2 Hardware of the CR1000 do not have a stand detecon feature

to enable moon detecon reading when the CR1000 is in a stand. To congure

these hardware revisions for moon detecon scanning, please refer to the CR1000

Conguraon Guide, located at www.codecorp.com/les.php and scan the appropriate

code.

See Secon 10.0 to learn how to determine your CR1000

hardware revision number.

Press and hold the buon on the top of the CR1000, the two blue bars eming from the

reader are used for targeng. Center the blue bars in the middle of a bar code. The opmal

reading distance from reader to bar code is approximately 4.0” (10 cm).

Once the reader is at the opmal distance, the reader will read the bar code. The CR1000 will

beep and ash a green LED to indicate a ‘good read’ has occurred.

To modify any default sengs, download the CR1000 Conguraon Guide at

www.codecorp.com/les.php and scan the appropriate code.

C005905_04_CR1000_User_Manual

6.0 - Reading Ranges

Note: working ranges are a combinaon of both the wide and high density elds. All samples were high quality codes

and were read along a physical center line at a 10° angle. Default AGC sengs were used. Accuracy= +/- 10%.

7.0 - Reader Feedback

Scenario Top LED Light Sound

CR1000 Successfully

Powers Up Green LED Flashes 1 Beep

CR1000 Successfully

Enumerates with Host

(via cable)

Once Enumerated,

the Green LED turns O 1 Beep

Aempng to Decode Green LED Light is O None

Successful Decode and

Data Transfer via Cable Green LED Flashes 1 Beep

Conguraon Code Successfully

Decoded and Processed Green LED Flashes 2 Beep

Conguraon Code successfully

decoded but wasn’t

successfully processed

Green LED Flashes 4 Beeps

CR1000 Performance

Test Code Min Inches (mm) Max Inches (mm)

3 mil Code 39 3.1” (80 mm) 4.0” (102 mm)

7.5 mil Code 39 1.3” (33 mm) 7.2” (182 mm)

10.5 mil GS1 DataBar 0.8” (20 mm) 8.7” (220 mm)

13 mil UPC 1.1”(28 mm) 11.0” (280 mm)

4.2 mil Data Matrix 1.9” (48 mm) 4.3” (110 mm)

5 mil Data Matrix 1.7” (43 mm) 4.5” (115 mm)

6.3 mil Data Matrix 1.3” (33 mm) 5.9” (150 mm)

10 mil Data Matrix 0.8” (20 mm) 7.1” (180 mm)

20.8 mil Data Matrix 1.1” (28 mm) 13.5” (343 mm)

C005905_04_CR1000_User_Manual

8.0 - Symbologies Defaulted On

Aztec

Codabar

Code 39

Code 93

Code 128

Data Matrix

Data Matrix Rectangle

9.0 - Symbologies Defaulted O

Aztec Inverse

Code 11

Code 32

Code 39 Extended Full ASCII

Code 39 Checksum

Composite

Data Matrix Inverse

Han Xin

The following are symbologies that have a default of ON. To turn symbologies on or o, scan the symbology bar codes located in

the CR1000 Conguraon Guide located at website at hp://www.codecorp.com.

The following are symbologies that have a default of OFF. To turn symbologies on or o, scan the symbology bar codes located in the

CR1000 Conguraon Guide located at website at hp://www.codecorp.com.

All GS1 DataBar

Interleaved 2 of 5

PDF417

QR Code

UPC/EAN/JAN

Matrix 2 of 5

Micro PDF417

Micro QR

MSI Plessey

Plessey

QR Code Inverse

Straight 2 of 5

Triopc

UPC-E Expansion

UPC Supplemental

10.0 - Locang the Hardware Revision Number

Locate the serial label on the boom of the reader to idenfy the hardware revision number of the CR1000.

Serial #: 20000XXXX

MFG #: CR1011_03

Designed in USA.

Made in Malaysia.

The number aer the underscore

( _ ) represents the hardware

revision number.

C005905_04_CR1000_User_Manual

11.0 - Reader ID and Firmware Version

Reader ID and Firmware

iVVVVWWWWXXXXSSSSSSSSSSAOODYYYYHHIIIIJJJJKKKKLLLL<TAB>Z…Z

To nd out the Reader ID and rmware version, open a text editor program (i.e., Notepad, Microso Word, etc.) and read the

following code:

You will see a text string indicang your rmware version and CR1000 ID number (see below):

i indicates ‘I’ string output;

VVVV is the applicaon rmware version number;

WWWW is the core applicaon rmware version number;

XXXX is reserved for the radio rmware version number;

SSSSSSSSSS is the Reader’s serial number (ten digits);

A is the current execuon state:

OO is the OEM idener;

D is the display type:

YYYY is the ash le system version number. Reserved;

HH is the hardware revision;

IIII is the hardware type idener: 0007 indicates a CR1000

JJJJ is the boot applicaon version;

KKKK is the operang system kernel version;

LLLL is the root le-system version;

<TAB> is the ASCII TAB character;

Z…Z is the OEM decoder version: a null terminated string of printable ASCII characters. Without a decoder.ini le,

the order of the decoders listed here indicates the order of use.

Example:

Xap/i3000300006040010002363A06D-SD+SQ

Note: Code will periodically release new rmware for CR1000 readers. For informaon on latest rmware versions,

call Code at (801) 495-2200. To upgrade rmware, please visit our website at hp://www.codecorp.com/

codesupport.php and follow instrucons provided.

“0” or “N” is no display device

“D” is the standard Keypad/Display

“A” means core is running

“B” means undened

“C” means undened

C005905_04_CR1000_User_Manual

12.0 - CR1000 Hole Mounng Paern

13.0 - CR1000 Overall Dimensions

NOTE 1:

LOCATING HOLES ARE 2MM IN DIAMETER, HOLE DEPTH is 1.5 MM

NOTE 2:

MOUNTING INSERTS ARE M3-.5 INTERNAL THREAD, 3.8MM LENGTH

Code Code Reader 1000 User manual

Popular Barcode Reader manuals by other brands