Cobra 29 LTD SE User manual
How to Use our
Cobra 29 LTD SE
Contents
Features..................................................................................................1
The CB Story.........................................................................................A1
Industry Canada Notice
CC Regulations and Warnings
Included Accessories
Controls & Indicators.......................................................................A2
Our Thanks to You .............................................................................A3
Customer Support
Installation
Location .............................................................................................2
Mounting and Connection .........................................................2
Antennas
CB Antenna.......................................................................................6
Marine Installation .........................................................................6
Ignition Noise Interference ..........................................................7
Operating Your 29 LTD SE
Turning On Your CB........................................................................8
Setting Channel Selector.............................................................9
Calibrate or SWR (Standing Wave Ratio)..............................10
To Receive..........................................................................................13
Selecting a Channel.......................................................................14
S-Meter ...............................................................................................14
NB-ANL/ANL/Off (Noise Blanker/Automatic.........................15
Noise Limiter Switch)
Bright/Dim Switch..........................................................................16
R Gain Control................................................................................17
Setting Delta-Tune .........................................................................18
Setting Squelch ...............................................................................18
To Transmit........................................................................................20
Setting Dynamike® ........................................................................20
Transmit..............................................................................................21
TalkBack..............................................................................................21
R Meter.............................................................................................22
External Speaker .............................................................................23
PA (Public Address) ........................................................................24
Home And Office Set-Up .............................................................26
Temporary Mobile Set-Up ...........................................................27
How Your CB Can Serve You..........................................................28
A ew Rules You Should Know ..................................................28
Channel 9 Emergency Messages..............................................28
CB 10 Codes......................................................................................30
Frequency Ranges.............................................................................32
29 LTD SE Specifications ................................................................33
Warranty Information .....................................................................34
Optional Accessories .................................................................35-36
Accessory Order Info .......................................................................37
If You Think You Need Service ...................................Back Cover
Features of This Pro uct
• 40 CB Radio Channels
• Special Edition Chrome Cabinet
& icrophone
• Heavy-Duty Dynamic
icrophone
• Full 4 Watts A RF Power Output
• SWR Calibration eter
• Talk Back
• Instant Channel 9
• 4-Pin Front ount icrophone
Connector
• Delta -Tune
• Switchable Automatic Noise
Limiter & Noise Blanker
• Adjustable Dynamike® Boost
• 9 Ft. ic Cord
• RF Gain
1
Installation
Installation
Location
32
Mounting and
Connection
Mounting and Connection
Hold the radio with the mounting bracket in
the exact desired location. If there is no
interference, remove the bracket and use it as
a template to mark the location for the
mounting screws.
Location
Plan location of transceiver and microphone
bracket before starting the installation.
Select a location that is convenient for operation,
yet does not interfere with the driver or passenger.
The transceiver is usually mounted to the
underside of the dash with the microphone
bracket beside it.
Note
The transceiver is held in
the universal mounting bracket
by two thumbscrews which
allow for adjustment at a
convenient angle.
The bracket includes two
self-tapping screws and star
washers.The mounting must be
mechanically strong,
conveniently located.
continued
Drill the holes and secure the bracket.
2
1
Connect the antenna cable plug to the
receptacle marked “ANT” on the back of
the unit.
3
Installation
Installation
54
Note
Connecting to an accessory fuse
prevents the unit from being left
on accidentally, and also
permits operating the unit
without running the engine.
Note
In positive ground vehicles the
red wire goes to the chassis and
the black wire is connected to
the ignition switch.
Note
Before installing the CB ra io,
visually check the vehicle’s
battery connection to
etermine which terminal,
positive or negative, is
groun e (positive is the
larger of the two) to the
engine block (or chassis). A
negatively groun e vehicle
has its negative lea
groun e to the chassis.
In a negative grounded vehicle, connect the
red lead of the DC power cord to an accessory
12 volt fuse.
Connect the black lead to the negative side of
the vehicle.This is usually the chassis. Any
convenient location with a good electrical
contact (remove paint) may be used.
4
5
Plug power cable into back of unit marked
“Power”. Be sure to observe polarity markings.
Mount the microphone
bracket on either side of
the unit (driver’s left)
using two screws
supplied. Bracket should
be placed under the dash
so microphone is readily
accessible.
6
7
Attach the 4-pin microphone cable to
receptacle, on the front of unit and install unit
on bracket securely.
8
Ignition Noise Interference
Antennas
Use of a mobile receiver at low signal levels is
normally limited by the presence of electrical
noise.The primary source of noise in automobiles
is from the alternator and ignition system.
Typically, when signal level is adequate, the
background noise does not present a serious
problem. Also, when extremely low level signals
are being received, the transceiver may be
operated with the vehicle’s engine turned off.The
unit requires very little current and therefore will
not significantly discharge the vehicle’s battery.
Even though the Cobra 29 LTD SE has an
automatic noise limiter, in some installations
ignition interference may be high enough to
make good communications impossible. Many
possibilities exist and variations between vehicles
require different solutions. Consult your COBRA
dealer or a 2-way radio technician for help in
locating the source of a severe noise.
CB Antenna
Since the maximum allowable power output of
the transmitter is limited by the CC, the antenna
is critical in affecting transmission distance. Only
a properly matched antenna system will allow
maximum power output. Cobra loaded type
antenna models are highly recommended for
most installations. Consult your Cobra dealer for
further details, or call 773.889.3087 and speak to
a Cobra representative.
Marine Installation
The transceiver will not operate at maximum
efficiency in a boat without a ground plate,
(unless it has a steel hull). Before attempting
installation , consult your dealer for information
regarding an adequate grounding system and
prevention of electrolysis between fittings in the
hull and water.
CB Antenna
7
Note
For optimum performance in
passenger cars the ideal
antenna location is on the
center of the roof. Second
choice is on the
center of the trunk.
Note
Because many newer trucks
feature fiberglass door skins, the
outside mirror must be
grounded to the chassis via a
ground strap when antenna is
mounted on the mirror bracket.
Note
3-way Combination
Antennas are also available
which allow operation of all
three bands (A -F & CB),
using a single antenna.
However, this type of antenna
usually results in less than
normal transmit and receive
range when compared to a
standard-type “Single Band” CB
antenna. Call 773-889-3087 for
further information.
6
1A standard antenna connector is provided
on the transceiver for easy connection.
The CB/PA button should be in the
CB position.
Operation
9
Operation
Turning On Setting Channel
Selector
8
Turning On
Make sure the power cord, antenna and
microphone are connected to their proper
connectors before starting.
Setting Channel Selector
2
EDITION
1
Rotate the On/Off Volume knob clockwise to
a normal listening level.
Select one of forty channels and adjust
volume.The selected channel is indicated by
the LED readout directly above the channel
selector knob
1
Operation
Operation
Calibrate For
SWR (Standing
Wave Ratio)
1110
Note
Antenna Indicator LED
will illuminate when TX if
SWR is high.
Note
Calibration must be made in an
open area (never in a garage).
Vehicle doors must be closed.
No one should be standing near
the antenna. (See your antenna
directions for more complete
information).
continued
Switch to the CAL position.
2
1
Calibrate for SWR (Standing Wave Ratio)
SWR calibration is done to properly adjust the
length of the antenna and to monitor the quality
of the coaxial cable and all R connections.
This calibration is critical in order to achieve
optimum performance.
Select channel 20.
Push and hold mic button.
3
While holding mic
button adjust the
SWR CAL knob so the
meter needle swings
to the CAL ▼mark on
the meter (located on the right).
4
Operation
13
Operation
12
Note
The reading will be slightly
higher on Channels 1 and 40
compared to Channel 20.
Note
When switched to SWR position
the meter needle should ideally
be as far to the left as possible.
Anything over 3 is not
acceptable.The antenna
indicator will light. A slight
antenna height adjustment
(higher or lower) may be
required. Repeat relcalibration
steps.
Repeat the same steps two through five
on Channel 1 and 40.This will check SWR for
all channels.
6
While still holding down the mic button, set
the S/R SWR CAL switch to the SWR position,
to read the SWR reading.
5
Rotate the On/Off Volume knob clockwise
the green RX/TX LED will be illuminated.
To Receive
1
To Receive
The S/R -SWR-CAL switch must be in the
S/R position to read the meter.
Operation
15
Operation
14
1
S-Meter
S-Meter
Swings proportionately to strength of incoming
signal when receiving.
Switch to NOR to select desired channel.
1
Selecting A
Channel
Selecting A Channel
NB-ANL/ANL/
OFF (Noise
Blanker/
Automatic
Noise Limiter)
Switch
Note
The RF noise blanker is very
effective in reducing repetitive
noises such as ignition
interference.
When switched to ANL the Automatic Noise
Limiter is activated.This helps reduce noise
created by the vehicle’s electronics.
When switched to NB/ANL position the R
Noise Blanker is also activated, providing
increased noise filtration.
When switched to O position all noise
filtration will be turned off.
NB-ANL/ANL/OFF (Noise
Blanker/Automatic Noise Limiter) Switch
1
Operation
Operation
1716
RF Gain Control
Bright/Dim
Switch
RF Gain Control
The R Gain is used to optimize reception in
strong or weak signal areas.
Bright/Dim Switch
Note
The RF Gain is used to optimize
reception in weak signal areas.
Switch to BRT or DIM to control brightness
of the channel indicator and multi-function
meter for day or nighttime driving. Rotate the R Gain knob counterclockwise
to reduce gain in strong signal areas. In weak
signal areas turn clockwise to increase gain.
1
1
ull clockwise rotation closes the gate
allowing only very strong signals to enter.
ull counterclockwise rotation opens the
“gate” allowing all signals in.
To achieve the Desired Squelch Setting (DSS),
turn the Squelch control counterclockwise
until you hear noise. Now turn the control
clockwise just until the noise stops. This is the
DSS setting.
Setting Delta-Tune
Delta-Tune functions as a“fine tune” control
enabling you to capture a more readable signal,
as well as eliminate adjacent channel interference.
Setting Squelch
Squelch is the “control gate”for incoming signals.
19
Setting
Delta-Tune
18
Operation Operation
1
2
1
3
Rotate Delta-Tune knob to the center
position for optimum tuning.
Gate open
Gate set to Desire
Squelch Setting (DSS)
Gate close
Setting Squelch
Table of contents
Other Cobra Radio manuals
Cobra
Cobra 29 LX EU User manual
Cobra
Cobra 75 ST EU User manual
Cobra
Cobra 29 NW LTD CLASSIC User manual
Cobra
Cobra 148 GTL ST User manual
Cobra
Cobra GR 29 LTD ST User manual
Cobra
Cobra 29 LX LE Operating instructions
Cobra
Cobra MR HH 500 FLT BT EU User manual
Cobra
Cobra 150 GTL DX Reference manual
Cobra
Cobra Harley-Davidson 29 LX HD LE User manual
Cobra
Cobra 19 MINI User manual
Cobra
Cobra CIR 1000 A User manual
Cobra
Cobra 18 WXST II User manual
Cobra
Cobra 29 LTD BT User manual
Cobra
Cobra 19DX IV User manual
Cobra
Cobra 75WXST User manual
Cobra
Cobra CIR2000A User manual
Cobra
Cobra 19 DX IV User manual
Cobra
Cobra 19 DX IB User manual
Cobra
Cobra 19 DX IV User manual
Cobra
Cobra 29 LX EU User manual
