CMOTech CCU-550 User manual
CCU-550 Modem User Guide
FCC RF EXPOSURE COMPLIANCE
In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report
and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency (RF)
electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the
safety standard previously set by both U.S. and international standards bodies. The design of this modem
complies with the FCC guidelines and these international standards.
Use only the supplied or an approved antenna. Unauthorized antennas, modifications, or attachments could
impair call quality, damage the modem, or result in violation of FCC regulations.
This CDMA 1xEVDO USB data modem has been tested for FCC RF exposure hand and body SAR
compliance with the CCU-550 USB dongle modem form factor. In order to comply with FCC RF exposure
requirements, the CDMA 1xEVDO USB data modem must be operated with the CCU-550 USB dongle
modem form factor. The use of this device in any other type of host configuration may not comply with FCC
RF exposure requirements and should be avoided. During operation, a 1.5cm separation distance should be
maintained between the antenna, whether extended or retracted, and the user’s/bystander’s body (excluding
hands, wrists, feet, and ankles) to ensure FCC RF exposure compliance.
CAUTION
Change or modification to the modem without the express consent of CMOTech Co., Ltd. voids the user’s
authority to use the equipment. This equipment has been tested and found to comply with the limits pursuant
to Part 22 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in an appropriate installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not used in accordance with instructions, can cause harmful radiation to radio communication.
However, there is no guarantee that interference will not occur in a particular installation. If the equipment
does cause harmful interference in radio and television reception, which can be determined by turning the
equipment on and off, the user is encouraged to try to correct the interference by one or more of the following
measures:
■Reorient or relocate the receiving antenna
■Increase the separation distance between the equipment and the receiver
페이지 1 / 22제목 없음
2005-06-13file://C:₩Documents%20and%20Settings₩Owner₩Local%20Settings...
■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
■Consult the dealer or an experienced Radio / TV technician for help.
CAUTION
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communication. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful unacceptable interference to radio and television reception,
which can be determined by turning the equipment on and off, the user is encouraged to try to correct the
interference by one or more of the following measures:
■Reorient or relocate the receiving antenna
■Increase the separation distance between the equipment and the receiver
■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
■Consult the dealer or an experienced Radio/TV technician for help.
CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions ; (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
POTENTIALLY UNSAFE AREAS
Posted facilities: Turn off this device in any facility or area when posted notices require you to do so.
Blasting areas: Turn off your modem where blasting is in progress.
Observe restrictions and follow any regulations or rules.
Potentially explosive atmospheres: Turn off your modem when you are in any area with a potentially
explosive atmosphere. Obey all signs and instructions. Sparks in such areas could cause an explosion or fire,
resulting in bodily injury or death.
Areas with a potentially explosive atmosphere are often but not always clearly marked. They include:
zfuelling areas such as gas or petrol stations
페이지 2 / 22제목 없음
zbelow deck on boats
ztransfer or storage facilities for fuel or chemicals
zvehicles using liquefied petroleum gas, such as propane or butane
zareas when the air contains chemicals or particles such as grain, dust or metal powders
zany other area where you would normally be advised to turn off your engine
It is recommended that this manual be read in conjunction with all other supporting documentation.
CCU-550 Modem Install
Setup
Insert installation CD (supplied with CMOTech Data Modem) into the CD-ROM drive.
This will automatically start the installation and install the required drivers plus CMOTech Data Modem
A
pplication software.
Do not connect CMOTech Data Modem into your laptop/PC yet.
The installation procedures are the Windows 2000 and Windows XP.
Start setup
If the auto run does not start after inserting the CD, please double-click on “Setup.exe” file on CD ROM to
start the installation.
If you have already inserted your Modem into your PC, remove the Modem and double-click “Setup.exe”
페이지 3 / 22제목 없음
2005-06-13file://C:₩Documents%20and%20Settings₩Owner₩Local%20Settings...
Start Auto Run
Install Shield Wizard... click 'next'
페이지 4 / 22제목 없음
2005-06-13file://C:₩Documents%20and%20Settings₩Owner₩Local%20Settings...
Choose the installation directory and click "Next" to continue.
CMOTech Modem is configuring your new software installation.
Co
py
in
g
Ste
p
1 File
페이지 5 / 22제목 없음
2005-06-13file://C:₩Documents%20and%20Settings₩Owner₩Local%20Settings...
Copying Step2 File
Check device
페이지 6 / 22제목 없음
2005-06-13file://C:₩Documents%20and%20Settings₩Owner₩Local%20Settings...
Installation Complete. Click “Finish” and remove the installation CD.
페이지 7 / 22제목 없음
2005-06-13file://C:₩Documents%20and%20Settings₩Owner₩Local%20Settings...
Insert Modem
Please Insert Modem
On Window 2000
A
s inserting Modem on Window 2000, there will not be any window and users can run applications after the
device is detected.
On Window XP
If your operation system is XP on inserting Modem, you can see “Find New Hardware” Dialog.
Click ‘Next’ button.
페이지 8 / 22제목 없음
2005-06-13file://C:₩Documents%20and%20Settings₩Owner₩Local%20Settings...
Click ‘Continue Anyway’ button.
페이지 9 / 22제목 없음
2005-06-13file://C:₩Documents%20and%20Settings₩Owner₩Local%20Settings...
Click ‘Finish’ button.
페이지 10 / 22제목 없음
2005-06-13file://C:₩Documents%20and%20Settings₩Owner₩Local%20Settings...
Table of contents
Other CMOTech Modem manuals
