Clevertronics LP CWSQLED Series User manual

1949210

V1.3

17 October 2018

Clevertest and Clevertest Plus

Refer to the supplementary operation guide supplied with the Product.

After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red

flashing for a period up to 2 minutes.

The diffuser will require removal to gain access to the Test/Status Switch and LED.

Maintained fittings (CWSQLEDM-yy-zz) cannot be scanned with a camera using the CleverSparky App

as the maintained light source interferes with the camera scanning function. To register the fitting

manually enter the serial number from the QR code and visually read the test result and enter manually

into CleverSparky.

Zoneworks and DATA Monitored Options

Argonauts Square with part numbers CWSQLEDx-ZW, CWSQLEDx-DATA are fitted with Zoneworks

communicationsmodules (nodes). These fittings are monitored using either Powerline Carrier Technology

that utilises the power cable to provide data communication or a dedicated data cable to/from data routers

installed on a dedicated data trunk connected to a central Server (can also be connected via

Ethernet/Internet/Fibre). Zoneworks software on the server is used to monitor, coordinate testing and

collate test data from each fitting. Zoneworks fittings can be commissioned by a single push of the test

switch or scanning of the supplied barcode. The LED Test Switch indicator provides a multifunction

indication of the status of the fitting during testing and normal operation:

State

LED Operation

Commissioned

LED on Solid (Green)

Un-commissioned

LED flashes at 0.5Hz (0.5s Green, 0.5s Yellow)

Emergency Light Test In Progress

LED flashes at 3s On (Yellow) & 0.5s Off

In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to

the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of

a Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl. DATA

version)

DALI EM Option

Argonauts Square with part numbers CWSQLEDx-DALI are fitted with DALI modules (nodes)that facilitate

connection and integration to 3rd Party Lighting Control Systems. Before installing the CWSQLEDx-DALI

please confirm that the Lighting Control System has the capability to monitor DALI Emergency Luminaires.

The CWSQLEDx-DALI will be addressed and configured into the control system by the Lighting Control

System Commissioning Technicians and not Clevertronics.

State

LED Operation

Commissioned/ Un-commissioned

LED on Solid (Green)

Emergency Light Test in progress

LED flashes at 1s On (Yellow) & 1s Off

“IDENTIFY COMMAND”

Fitting goes into emergency mode for 10 seconds

A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network. DALI

connections are marked as Da Da.

Argonaut Square LED Sensor Light

Installation & Maintenance Instruction Leaflet

Victoria (Head Office & Manufacturing)

195 Chesterville Rd

Moorabbin VIC 3189

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

New South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9248 3720

Fax: +61 8 9248 3725

New Zealand

Phone: +64 800 548 448

Designed in Australia to comply with the requirements of

AS2293.3: 2005 and AS/NZS CISPR15: 2011

NOTE: Standard product codes with this symbol are

enabled with Clevertest Plus capability. Please refer to the

operation guide supplied with the product for details.

Models:

CWSQLEDx-yy-zz-vv

Testing:

Options:

Manual Test

zz = Blank

Non-Maintained

x = N

Zoneworks

zz = ZW

Maintained

x = M

Z/W DATA

zz = DATA

Microwave Sensor Hi/Lo Control

yy = MS-HL

DALI Comp.

zz = DALI

Microwave Sensor Control

yy = MS

Clevertest

zz = CT

Black Body

vv = BLK

(NOTE: -CTProducts supplied with the Clevertest Plus Symbol are activated with Clevertest

PLUS capability. Please refer to the operation guide supplied with the product for details).

Spare Parts:

1550290

BATT: LP 6.4V 3.2Ah.200mm lead.Stick.Brkt

1190320

Sensor: M/Wave Motion, SK-503L DC

(for -MS-HL)

1330120

LED Driver –GDY250, 26W 42VDC 610mA

8002840

PCA: SQ LED Array, 215mm, 400K, 3020 LED

CCPLED-38V120C-CKIT

LED Power Pack, 38V 120mA, LP

1190325

SENSOR:M/Wave Motion, SK-601 On/Off

(for -MS)

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Australian and International Standards.

1949210

V1.3

17 October 2018

Installation:

The LP Argonaut Square (CWSQLEDx) can be installed either Ceiling or Wall Mounted.

•Remove the four (4) screws diffuser to the base.

•Remove the four (4) screws holding the gear tray to the base.

•Determine the cable access point. There are 2 locations on opposite sides of the fitting for cable

gland/conduit entry. Entry can also be from the back of the base. Drill out the desired cable entry

point.

•Drill out 4 of the mounting points in the base (see image below).

•Using the base as a guide, mark the 4 holes for mounting and one for mains access if using back

cable entry.

•Mount the base using appropriate fixings and seal these fixings with silicone (fill any additional entry

points with silicone also)

•Route the power inside the base.

•Connect the 240VAC (A,E,N,SA) supply to the terminal block of the gear tray.

•Install the gear tray to the base.

•Apply power to the fitting and test per the instructions.

•If the CTP capabilities are activated, please affix the CTP status Label to a visible surface.

Networking:

When installing the product on a monitored network, (ZONEWORKS, DATA, DALI) simply insert the

relevant Smart Node PCA.

Dimensions:

Testing:

Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24

hours. Conduct the following tests:

•For the first test, the emergency lamp must remain illuminated for at least 2 hours after

disconnection from the mains supply.

•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are

required to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails

to remain illuminated for the requisite time, remedial action must be taken to repair the situation

and once completed, the unit must pass a subsequent test. For more specific information, please

refer to the current edition of the AS 2293.3 Standard.

Maintenance:

Lamp Replacement:

•Use only the lamp(s) recommended on the

label inside the Argonaut.

•To replace the lamp bar, remove the self-

tapping screws, disconnect the signal cable

and install the new lamp bar.

Battery Replacement:

•Use only the battery recommended on the

label inside the Argonaut and on this

instruction.

•Remove the fasteners holding the battery,

un-plug the lead from the PCB and remove

the old battery.

•Attach the new battery, route the DC cable

to the PCB and plug the new battery.

Trouble Shooting:

Below are a list of common problems and their

possible causes.

Fault: The Green LED Test Switch

indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in

emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency

mode, but only stays on for a short

period.

Check: Battery has been allowed to charge for

at least 24 hours.

Battery for damage.

Rated Emergency Lumen Output in accordance with AS2293.1 (refer

to spacing tables for installation positions):

C0=D50 C90=D50

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries

discharged or “cycled”. The battery in this fitting has been selected to give excellent long-life

performance in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-

life performance and may lead to premature battery failure. Battery warranty claims, as a result of such

abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

Mounting Holes

Cable Entry

Other Clevertronics Lighting Equipment manuals

Clevertronics

Clevertronics L10 CleverFit Exit LCFLED Series User manual

Clevertronics

Clevertronics L10 Cleverfit Pro LCFPRO-TH Series Installation and operating instructions

Clevertronics

Clevertronics LP CBS4N Series Installation and operating instructions

Clevertronics

Clevertronics l10 LBULKy Series Installation and operating instructions

Clevertronics

Clevertronics L10 LBLLED-REC-WM Series Technical specifications

Clevertronics

Clevertronics FBKLED Series Installation and operating instructions

Clevertronics

Clevertronics CLP CCFPRO Series Installation and operating instructions

Clevertronics

Clevertronics LP CWP2LIFE-PRO-WPPOD Series Installation and operating instructions

Clevertronics

Clevertronics L10 LIFELIGHT PRO LLIFE-PRO SPOT Series Installation and operating instructions

Clevertronics

Clevertronics CleverEVAC L10 UltraBlade Pro Dynamic Red Installation and operating instructions

Clevertronics

Clevertronics LED CIRCLITE Installation and operating instructions

Clevertronics

Clevertronics TS Trade Series Installation and operating instructions

Clevertronics

Clevertronics L10 Argonaut PLUS User manual

Clevertronics

Clevertronics L10 Cleverfit Pro Installation and operating instructions

Clevertronics

Clevertronics Argonaut PLUS Maintenance and service guide

Clevertronics

Clevertronics L10 LJELED-40 Series User manual

Clevertronics

Clevertronics CLP LIFELIGHT PRO Technical specifications

Clevertronics

Clevertronics L10 ARGOPRO-1200-L10POD Series User manual

Clevertronics

Clevertronics L10 Supalite LFLLED Series User manual

Clevertronics

Clevertronics CLP CWSQLED Series Manual

Clevertronics

Clevertronics LP Cleverfit Pro CCFPRO TH Series Installation and operating instructions

Clevertronics

Clevertronics Trade TS CIRCLITE ECLLED Series Installation and operating instructions

Clevertronics

Clevertronics L10 Cleverfit LCFLED Series Installation and operating instructions

Clevertronics

Clevertronics L10 LVP2LEDM-P Series Installation and operating instructions

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions