Clearaudio Emotion SE User manual
Emotion SE
clearaudio electronic®GmbH
Spardorfer Str. 150 • D-91054 Erlangen • Tel. +49 9131 40300100 • FAX + 49 9131 40300119
www.clearaudio.de • www.analogshop.de • info@clearaudio.de
© clearaudio electronic GmbH 2016
Version: 1.3_09_2016
User manual
Bedienungsanleitung
Made in Germany
User manual 2 - 16
Bedienungsanleitung 17 - 31
Dear Clearaudio customer,
Congratulation’s to your choice of the
Emotion SE
turntable, a world class turntable, made by Clearaudio
electronic GmbH.
A resonance minimized shape in combination with a stand alone motor unit, guarantees total isolation of
resonances from the turntable chassis, providing the best music reproduction and authentic High End
imaging. A high precision, patented Clearaudio -
CMB-bearing-technology
is completing the analogue
pleasure.
Please read this instruction carefully, to avoid any damages or loss of warranty.
These instructions will help you with an easy setup and guarantee the highest pleasure for a long time.
We wish you a lot of musical enjoyment with your new
Clearaudio
Emotion SE
turntable.
Clearaudio electronic GmbH
Emotion SE
User manual
Bedienungsanleitung
CE-MARKING
COPYRIGHT
Recording und reproduction of any sound-material may require the consent of the creator.
Please acknowledge the information given in the
- Copyright Act 1956,
- Dramatic and Musical Performers Act 1958,
- Performers Protection Acts 1963 and 1972, any more recent legal regulations.
Page / Seite 2 © clearaudio electronic GmbH 2016
The Clearaudio
Emotion SE
meets the regulations concerning electromagnetic disturbance
(EMC) and low-voltage appliances.
Contents
1. Packing overview 4
2. List of components 5 - 6
3. Installation and setup 7 - 14
4. Special information 15
5. Technical data 16
Warranty information 32
Page / Seite 3 © clearaudio electronic GmbH 2016
Emotion SE
User manual
Bedienungsanleitung
1. Packing overview
Page / Seite 4 © clearaudio electronic GmbH 2016
Pic. 1: Packing overview
Emotion SE
User manual
Bedienungsanleitung
1. Layer (top):
Motor-unit, motor-base (not shown)
top of bearing, belt, pulley, ttings and
accessories.
If ordered as package:
Clearaudio Satisfy Carbon tonearm
and/or Clearaudio pickup
2. layer (middle):
Turntable – chassis with
integrated lower bearing part
3. layer (bottom):
Platter
2. List of components
Clearaudio has developed a special and secure turntable packing to prevent your
Emotion SE
turntable
from any transportation damage.
Please store this original packing, in case you need to ship the turntable.
Below you can nd the content of delivery of your Clearaudio
Emotion SE
turntable:
Page / Seite 5 © clearaudio electronic GmbH 2016
Emotion SE
User manual
Bedienungsanleitung
123
1Turntable chassis with mounted lower
bearing part, tonearm base and height
adjustable feets
4Motor drive unit with main lead and
motor base
2Turntable platter 5Acrylic motor pulley
3Bearing (upper part) with adjusted
bearing shaft
6Optional:
Clearaudio
Satisfy Carbon
tonearm
directwired, when ordered as a package
456
Pic. 2.1: List of components
Page / Seite 6 © clearaudio electronic GmbH 2016
Emotion SE
User manua
lBedienungsanleitung
78 9
10 11 12
13 14 15
71 Pair of gloves 13 Screw driver
8Grounding wire for the
Emotion SE
turntable
14 Bearing oil
9 Clearaudio logo, self-adhesive 15 Clearaudio
Smart Stylus Gauge
(without cartridge)
10 Level gauge for the turntable alignment 16 Not shown:
User Manual
11 2 pcs. drive belt (2 x 292 mm) 17 Not shown:
Warranty card, Clearaudio Quality
Certicate and return delivery note
12 3 pcs. hex wrench (sizes: 1.5 / 2.5 / 3) 18 Not shown:
Optional: Clearaudio MM Cartridge
and
Smart Stylus Gauge
, only when
ordered as package
Pic. 2.2: List of components
Page / Seite 7 © clearaudio electronic GmbH 2016
Emotion SE
User manual
Bedienungsanleitung
3. Installation and setup
The setup and installation of the
Emotion SE
is done quickly and very easy.
Please use the white gloves during this procedure, to avoid scratches.
1.)
You should consider a safe and clean working area for the installation, as near as possible to the nal
position of the
Emotion SE
turntable.
First take out the motor and tonearm of the packing. Now you should take out the rst packing layer.
After that you can take out the
Emotion SE
turntable chassis from the next packing layer.
Place the turntable body on a clean underlay.
To avoid any damages to your bearing, the turntable platter should achieve room temperature
before the set up begin (approx. 20 ° Celsius).
2.)
Take the upper bearing part and place it on the lower bearing part, which is already integrated in the
chassis (picture 3).
3.)
Place the platter with both hands carefully onto the bearing.
Through a lightly (!!) up and down movement the platter will slip onto the bearing upper part (picture 4).
Avoid major side force to prevent any damages to the ceramic bearing!
Pic. 3: Placing the bearing Pic. 4: Placing the platter
Make sure with gentle pressure that the platter is applying on the complete surface of the bearing.
Page / Seite 8 © clearaudio electronic GmbH 2016
4. ) Alignment of the turntable
The following adjustment is very important!
Place the Clearaudio
level gauge
on the platter (see Pic. 5) and bring the turntable in level by turning the
corresponding feet in the right direction.
The turntable is in level, when the air bubble in the level gauge is in the center.
Adjust the height of the turntable by turning the feet counter wise with the delivered hex wrench (shown in
picture 6).
Only if the turntable is proper aligned you will receive the best possible sound.
Emotion SE
User manual
Bedienungsanleitung
Pic. 5: Alignment of the turntable
Pic. 6: Height adjustment
Page / Seite 9 © clearaudio electronic GmbH 2016
Emotion SE
User manual
Bedienungsanleitung
The following instructions are for
Emotion SE
packages.
If you use a tonearm and / or cartridge from different manufacturer please follow the instruction manual of
the particular manufacturer.
3.1 Tonearm set-up
1.)
Take the
Satisfy Carbon
tonearm and slide rst the
signal cable and then the tonearm shaft into the
hole of the tonearm base at the right upper corner
of the
Emotion SE
turntable chassis. Please ensure
that the tonearm tube is parallel to the side edge
of the chassis turntable.
Tighten the tonearm only slightly with the provided
hex wrench and screws.
Before you nish the tonearm setup, please
proceed with the cartridge setup.
The correct height adjustment that is going to be used for the tonearm is depending on the cartridge you
install.
2.)
For the next steps, please mount your cartridge on your tonearm (optional as a package: Clearaudio
Satisfy Carbon
tonearm). Please leave the stylus protector on the cartridge.
Use the manufacturer’s instruction manual during this installation procedure and follow the appropriate
instructions.
The headshell wires (cartridge connection leads) are colour coded according to the international standard:
Pic. 7: Setup of the tonearm
Colour code of the
Satisfy Carbon
tonearm wire:
Signal left channel (L+) >> white
Signal ground left channel (L-) >> blue
Signal right channel (R+) >> red
Signal ground right channel (R-) >> green
Please pay attention on every step to avoid any damages to the cartridge!
!
Now adjust the tracking force of the cartridge.
Please follow the instructions according the manual of the cartridge you use.
If you are using a Clearaudio Moving Magnet cartridge you can adjust the tracking force or the wiring of
the tonearm (about 20 mN), by turning the tonearm`s counter weight on the threaded bolt (backside view
of the tonearm).
Page / Seite 10 © clearaudio electronic GmbH 2016
Emotion SE
User manual
Bedienungsanleitung
3.)
For a more comfortable adjustment, please take the delivered
Smart Stylus gauge
(only in the
Emotion SE
package with tonearm and cartridge) and adjust the tracking force by using the gauge.
Please place the
Smart Stylus gauge
on the platter and put the cartridge on the ne line which is marked
with the recommend tracking force for your cartridge (e.g. Clearaudio MM cartridge 20 mN (2.0 gram)).
Pic. 8: Use of the
Smart Stylus Gauge
✓
tracking force too high!
tracking force too low!
This position of the diamond correlates
to a tracking force of 20 mN (2.0g).
If you would like even more professional set up tools, you can also use other tools like the Clearaudio
Weight Watcher gauge
(Art. No. AC094).
For more information on that, please contact your specialist dealer or directly Clearaudio
www.analogshop.de.
For contact address see page 14.
Other manuals for Emotion SE
4
Table of contents
Languages:
Other Clearaudio Turntable manuals
Clearaudio
Clearaudio Jubilee MM User manual
Clearaudio
Clearaudio double matrix professional SONIC User manual
Clearaudio
Clearaudio Jubilee MM User manual
Clearaudio
Clearaudio Avantgarde Magnum User manual
Clearaudio
Clearaudio Performance DC User manual
Clearaudio
Clearaudio Performance SE User manual
Clearaudio
Clearaudio Master Innovation User manual
Clearaudio
Clearaudio TT5 User manual
Clearaudio
Clearaudio Unify User manual
Clearaudio
Clearaudio Master Innovation User manual
Clearaudio
Clearaudio Statement V2 User manual
Clearaudio
Clearaudio Concept User manual
Clearaudio
Clearaudio Innovation Compact User manual
Clearaudio
Clearaudio Bluemotion & Satisfy User manual
Clearaudio
Clearaudio Double Matrix Professional User manual
Clearaudio
Clearaudio smart power 12V User manual
Clearaudio
Clearaudio TT1 MI User manual
Clearaudio
Clearaudio Pulley extractor device User manual
Clearaudio
Clearaudio Smart matrix professional User manual
Clearaudio
Clearaudio Smart Matrix User manual
