Clear WIXB-175 User manual
Page 1 of 21
Clear Modem Series G
User Guide
Model: WIXB-175
Manual Version: 1.3
Manual Date: July. 16 2009
Page 2 of 21
Overview
Thank you for purchasing the Clearwire CPE Indoor (WIXB-175) desktop device. The Desktop
CPE allows you to connect to the wireless world easily and seamlessly without complicated
installation and setup procedures. In addition it offers you the ability to make Voice over
Internet Protocol (VoIP) calls.
The Desktop CPE indoor device provides the user:
Convenience — with easy plug and play functionality.
Performance — High gain antennas supply diversity technology. Best in Class range and
indoor penetration.
Control — remote management capability allows easy detection and authentication once
the unit is setup.
VoIP - One RJ11 port allow for Voice over IP calls using your CPE.
Powerful Features in a Single Unit
The CPE device provides the following features:
WiMAX Authentication
WAN DHCP Client
LAN DHCP Server
Home Gateway Functions
Front of CPE
The Front of the CPE units contains LED Link/Activity indicators. The LEDs provide the status
of the unit and signal strength indicators for easy adjustment during setup.
Front of Unit
LED Indicator Interface
The Power LED shall be Blue and the other LEDs shall be Green.
Page 3 of 21
Power Status
The Power LED shall be on when the device is plugged in and has power.
Ethernet Status
The Ethernet LED should be on when the LAN Ethernet has been established and activity has
been detected.
Signal Strength
Once the device has registered on the network, the Signal Strength LEDs should be on
depending on different strength. Only one Signal Strength LED lit represents low signal
detected and all five Signal Strength LED lit presents high signal detected.
Back Panel Ports Description
Power AC Power Connector
Phone Line RJ-11 port for use with VoIP.
Ethernet Port
Reset button
Note: Hardware Reset Button (A paper clip is recommended for accessing this button). Before
resetting the CPE, ensure the power LED is ON. Hardware Reset Button will cause
PASSWORD, DEVICE NAME and LAN IP to be restored to default. If you would like to reset to
default as ex-factory setting, please do it via Basic/Restore Factory Settings.
Operating Information
Operating temperature for this unit is 0℃-40℃ (32-104F).
Installation
Overview
To install the Desktop CPE Series, you need to review the following sections:
Before You Begin
Easy Setup
Before You Begin
Before you begin installation, check that you have received the following items with your
Desktop CPE:
In the box with your CPE you should have:
Item Description
Power Adapter Power adapter connects the Clear Modem to an AC electrical outlet.
Page 4 of 21
Ethernet Cable The Ethernet cable connects the Internet port on your Clear Modem to
your PC or laptop computer.
Clear Modem
Quick Start Guide Provides quick installation instructions for getting your Desktop CPE up
and running.
Welcome Letter A brief introduction of the stuff inside the packaging and customer
service contact window.
Regulatory letter The FCC regulatory statement for this Clear Modem
In addition, you will also need:
A computer
An RJ-11 telephone cable (optional, if you would like to use VoIP function).
Easy Setup
The CPE is easily set up in your home. Basic installation equipments needed are the power
adapter, Ethernet cable and a PC or laptop computer and the CPE device. If you want to use
the VoIP functionality, you will also need an RJ-11 phone cable and a telephone [external ATA
is needed].
Perform the following tasks before powering up the unit:
Stand the Clear Modem on a flat surface.
Plug the power adapter into the power connector on the back of the unit.
Plug the AC power cord into an AC outlet. The unit will turn on.
Plug one end of the Ethernet cable into the Ethernet connector on the back of the unit.
Plug the other end of the Ethernet cable into the Ethernet connector of your computer.
To use VoIP functionality of the phone, plug one end of the phone line into the activated
phone connector on the back of the unit. Phone line activation is dependent upon your
service contract.
Plug the other end of the phone line into the phone line connector of your telephone.
Page 5 of 21
Procedure to Log into the CPE
Before you Begin Configuration, some settings on your computer must be verified or changed
to ensure that your computer configuration can support the Desktop CPE.
Verify that the IP addresses and DNS settings are automatically generated in your Local Area
connection of your Internet Protocol (TCP/IP) properties. Refer to the chapter titled
"Configuring TCP/IP" for information on how to do this.
Logging In to the CPE
Use the following procedure to log into the Desktop CPE.
1. On a computer that is connected to the Clear Modem Series G, open a web browser.
2. In the Address or Location field, type http://192.168.15.1 and press ENTER to display the
login screen.
Login Screen
3. In the Password field, type the password (default is CLEAR123).
4. Click Login.
Page 6 of 21
Basic Menu
The Basic menu provides the following tabs:
Password
Time Zone
Device Name
Reset Factory Settings
Password Tab
The password tab allows you to enable/disable password protection. You can also change
your password here.
Field or Button Description
Enable Login Password
Protection
Checking this box will require login password
protection.
New Login Password Enter your new password here. Maximum 20
characters. Passwords are case-sensitive.
Confirm New Login
Password
Re-enter your new password here, exactly as
entered above.
Be sure to click the Apply button once you are finished.
Page 7 of 21
Time Zone Tab
The Device Time Zone tab allows you to establish the time zone for your location. It also
allows you to automatically adjust for Daylight Savings Time if necessary.
Field or Button Description
Current Local Time Shows the current local date and time.
Time Zone Select your local time zone from the drop down
box.
Auto Adjust for Daylight
Saving Time
Check this box if your location observes Daylight
Savings Time. (Default is checked)
Be sure to click the Apply button once you are finished.
Page 8 of 21
Device Name Tab
The Device Name tab allows you to re-name your CPE device. This is the Device Name you
enter on an internet browser address bar to access your CPE device.
Field or Button Description
New Device Enter the new name for the CPE device.
Name Maximum 20 characters.
Be sure to click the Apply button once you are finished.
Page 9 of 21
Restore Factory Settings Tab
The Restore Factory Settings Tab will reset your CPE to the manufacturers default settings.
Be sure to click the GO button if you are sure you want to reset factory settings. The CPE will
reboot automatically after the GO button has been clicked.
Advanced Menu
The Advanced Menu provides the following tabs:
Firewall
Internet Protocol
Dynamic DNS
Port Forwarding
Local Address
Page 10 of 21
Firewall Tab
A firewall helps to protect your home network from unauthorized access. It will also help to
manage authorized access from the internet to your CPE
Field or Button Description
Enable Firewall Check this box to enable the firewall for your home
network.
Enable Web Login from
Internet (Grayed out if Enable Firewall is not selected). Check
this box to enables you to access your CPE device
from a network other than your own.
Web Login Port from
Internet
Choose a port number to connect to when logging in
from a network other than your own. The default is
8080.
Enable ping from Internet
Enables the CPE to respond to a ping from the
Internet. This option would be enabled to allow testing
only. Do not leave this enabled.
Be sure to click the Apply button once you are finished.
Table of contents
Other Clear Modem manuals
Clear
Clear Spot 4G User manual
Clear
Clear Spot 4G+ Specification sheet
Clear
Clear Spot 4G User manual
Clear
Clear MODEM with Wi-Fi User manual
Clear
Clear G SERIES User manual
Clear
Clear Spot 4G+ User manual
Clear
Clear WIXFBR-117 Specification sheet
Clear
Clear G SERIES Specification sheet
Clear
Clear Stick Atlas PXU1960 User manual
