Claudgen HE7402RF Manual

41001333 iss 01

Consort Equipment Products Ltd

Registered Office: Thornton Industrial Estate

Milford Haven, Pembrokeshire, S 73 2RT

Tel: 01646 692172 Fax: 01646 695195

BS EN ISO 9001 Registered Company No FM12671

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR

W rm Air Curt in He ters

C t logue Number: HE7402RF 3kW & HE7420RF 4.5kW- 230/240V

PLEASE RETAIN THIS LEAFLET FOR FUTURE MAINTENANCE

MODELS

These units are 622mm wide 3kW & 4.5kW modular heaters designed

for mounting above doorways and similar entrances, and may be used

as space heaters. 1040mm 4.5kW and 6kW modules are also

available.

MOUNTING

When mounted over a standard shop doorway the unit should be

fitted as low as possible and not more than 2.3 meters from ground

level. single unit will provide reasonable coverage for a one metre

doorway, and for wider doorways units can be mounted end to end.

The unit should be positioned so that the airflow is not obstructed by

any part of the doorframe.

INSTALLATION

Carefully unpack the unit and remove the top cover fixing screws.

The heater may be mounted using the mounting bracket provided.

Loosen mounting screws, allowing the mounting bracket to be

removed from the unit. Making sure that the mounting bracket is

horizontal, fix the bracket to the wall using 4 x No 8 wood screws.

Place the unit on the mounting bracket ensuring the washers are

spaced as shown on diagram 2 (a plain washer either side of the

mounting bracket).

Tighten screws to hold the unit at the required angle.

Fig 2 WALL BRACKET ASSEMBLY

The heater may also be mounted directly onto a suitable wall or

bearer by four No. 8 wood screws through the holes provided in the

back of the unit casing. Keyhole slots are provided for the top two

fixings (fig 1).

ELECTRICAL CONNECTIONS

These units are suitable for connection to a 230/240 volt 50 Hz single

phase ac supply. The heaters consume 4.5kW & 6kW respectively at

240 volts when switched to the full heat position.

Model HE7402RF – 3kW

Model HE7420RF – 4.5kW

The appliance should be connected to the supply via a circuit in

which there is an all-pole switch. Test for correct operation and

refit the cover.

Fig 1

OUTLINE DRAWING

41001333 iss 01

Fig 3 WIRING DIAGRAM

NOTE: The unit MUST be reli bly e rthed.

OPERATION

This he ter is controlled by Celsi Zone Controller CZC1 nd c n

only be used when connected. Each CZC1 can control any number

of heaters. The heater has an indicator light positioned on the fascia

panel on the top left side. The light may be:

Green - when no heat is needed

Yellow - when some heat is needed to maintain

the room temperature

Red - when the heater is on full power

F st Fl shing Red - when the heater has overheated and an

Electronic Safety Control has switched

the heater off.

Please refer to the user and operating instructions for the CZC1 for

detailed instructions.

ELECTRONIC SAFETY CONTROL

The appliance is fitted with an Electronic Safety Control (ES). This is

a safety device which switches the heater off if, for any reason, the

appliance overheats. The overheating is indicated by fast flashing

red light. The ES control can only be re-set after the appliance has

cooled down. In order to re-set the ES control, proceed as follows:

•Switch the appliance off at the mains by using the isolator

switch and leave to cool down for approximately 5 minutes.

•Switch appliance back on and the ES control will re-set.

Ensure that the appliance is functioning correctly. If the ES control

operates again, the appliance should be checked by a competent

electrician.

MAINTENANCE

lways ensure that the main external electricity supply is switched

off before attending to the servicing of your Claudgen Screen-Zone

heater.

To obtain best results from your heater it is necessary to avoid the

build up of dust and dirt within the unit and on the air inlet and

discharge grills. For this reason regular cleaning is necessary, paying

particular attention to the removal of dirt build up on the rotor

blades. single drop of light oil should be applied to the motor

bearing from time to time.

TO REPLACE THE FAN HEATER ASSEMBLY

a) Remove the top cover.

b) Disconnect the internal wiring from the main terminal block and

earth stud.

c) Release the three fixings which secure the switch bracket to the

right hand of the main case.

d) Remove the four nuts and washers fixing the fan heater

assembly to the back of the case.

e) The fan heater assembly can now be eased forward and

removed from the heater case.

f) Fit replacement fan heater and reassemble in reverse order.

SPARES

It is essential when ordering spares or replacement parts to state the

model number and the serial number on the rating place fixed to the

top of the unit.

In the interest of progress the Company reserve the right to vary

specifications from time to time without notice. The material listed

is offered subject to the Company’s General Conditions of Sale, a

copy of which can be obtained on request.

NOTE: DO NOT COVER ny of the ir inlet or outlet grills, t ny

time.

This manual suits for next models

Table of contents

Other Claudgen Heater manuals

Claudgen

Claudgen HE7230 User manual

Claudgen

Claudgen HE7237 User manual

Claudgen

Claudgen HE7230SL User manual

Claudgen

Claudgen ScreenZone HE8409 User manual

Claudgen

Claudgen HE7010SL Use and maintenance manual

Claudgen

Claudgen RAC4500 Manual

Claudgen

Claudgen ScreenZone CA1309S10 User manual

Claudgen

Claudgen HE7433 Original operating instructions

Claudgen

Claudgen HE8320 Original operating instructions

Claudgen

Claudgen HE7402 Original operating instructions

Claudgen

Claudgen RCT250SL Use and maintenance manual

Claudgen

Claudgen Heat-Zone Manual

Claudgen

Claudgen HE6502 Manual

Claudgen

Claudgen ScreenZone RAC10HL User manual

Claudgen

Claudgen SCREENZONE RAC1306 User manual

Claudgen

Claudgen HE7237 Manual

Claudgen

Claudgen CH06CSi User manual

Claudgen

Claudgen Sanfire 40 Manual

Claudgen

Claudgen ScreenZone RAC0603 User manual

Claudgen

Claudgen HE7230W Installation and operating instructions

Claudgen

Claudgen HE8515 Manual

Claudgen

Claudgen ScreenZone CA1514S10 User manual

Claudgen

Claudgen CA1309S Manual

Claudgen

Claudgen CH06CS Manual

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide