Clare CLR-C1-RCDW Assembly instructions

ClareOne Recessed Door/Window Sensor

Installation Sheet

Last modified: 08/18/20

Part number: CLR-C1-RCDW

Description

The CLR-C1-RCDW Recessed Door/Window Sensor is a

supervised, wireless sensor that detects the opening and

closing of doors or windows. The sensor and magnet are

recessed mounted into the frame and feature a double tamper

of both the sensor and case for added security.

When activated, the sensor transmits an open (trip) or close

(restore) signal to the panel. The sensor also provides

supervisory, tamper, and low battery (as needed). The sensor

is powered by (1) replaceable 3-VDC Lithium CR2 battery.

Installation

Follow the provided installation guidelines.

Note: Verify mounting location before drilling any holes.

•The area must be able to accommodate an 11/16”

hole to a depth of 2 1/4” for the sensor and 5/8” for

the magnet.

•The holes must be drilled directly across from each

other to ensure magnet and sensor operate properly.

•Pull the battery tab out of the sensor before operation,

necessary for adding the sensor to the panel.

To install the recessed door/window sensor:

1. Using an 11/16” drill bit, drill a 5/8” deep hole for the

magnet.

2. Mark the location directly across for the sensor hole, and

then drill a 2 ¼”deep hole for the sensor.

3. Push both magnet and sensor into mounting holes until

they are flush against the frame.

Notes

•The magnet and sensor are slightly larger than the

drilled hole to ensure a snug fit. Slight routing of the

hole may be required. Verify that there is good

door/window closure.

•Mount in the side or top of the door/window.

Programming

To add the sensor to the ClareOne panel:

1. Ensure the magnet and sensor are in their not faulted

position (door/window closed).

2. Put the ClareOne panel into sensor paring mode. For

detailed programming instructions, refer to the ClareOne

Wireless Security and Smart Home Panel User Manual

(DOC ID 1871).

3. Trip the sensor by opening the door/window (separating

the magnet from the sensor).

2 / 3 DOC ID –1980 • Rev 01

Testing the Sensor

Verify that the sensor is working properly.

To test the sensor:

1. Set the panel to the sensor test mode.

2. Take the sensor and magnet to the desired mounting

location, making sure to line up their alignment marks with

each other. Trip the sensor by pulling the magnet away

from the sensor.

3. Monitor the system after tripping the sensor. Refer to the

ClareOne Wireless Security and Smart Home Panel User

Manual (DOC ID 1871) for specific test information.

Note: If a low battery notification occurs, replace the

battery within 7 days.

Caution: Battery may explode if mistreated. Do not recharge,

disassemble, or dispose of in fire.

Battery replacement

Once the sensor has indicated there is a low battery, the

battery must be replaced within 7 days.

To replace the battery:

1. Remove the sensor cap, and then carefully pull out the

circuit board.

2. Gently push the battery outward towards the antennas,

noting the polarity.

3. Removing it completely, and then press a new battery into

its place.

4. Carefully slide board back into housing, note the slot for

alignment.

5. Replace the cap, and then activate the device at least five

times to ensure proper operation.

Specifications

Compatible Panel

CLR-C1-PNL1

RF frequency

433.95 MHz

Battery type

(1) 3-VDC, Lithium CR2 battery

Battery

Panasonic CR2

Operating environment

Temperature

Relative humidity

32 to 120°F (0 to 49°C)

95% noncondensing

Dimensions (L × D)

2.25 × .75 in

(57.15 × 19.05 mm)

Regulatory information

Manufacturer

Clare Controls, Llc.

7519 Pennsylvania Ave, Suite 104

Sarasota, FL 34243

North American

standards

ETL. ETLC

FCC compliance

FCC / IC Statement

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable

protection against harmful interference in a

residential installation.

Per FCC 15.19 (a) (3) and (a) (4), This device

complies with part 15 of the FCC Rules.

Operation is subject to the following conditions:

(1) this device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesirable operation.

Per FCC 15.21, The user manual or instruction

manual for an intentional or unintentional radiator

shall caution the user that changes or

modifications not expressly approved by the party

responsible for compliance could void the user's

authority to operate the equipment. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation.

If this equipment does cause harmful interference

to radio or television reception, which can be

determined by turning the equipment off and on,

the user is encouraged to try to correct the

interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment

and receiver.

•Connect the equipment into an outlet on a

circuitdifferent from that to which the receiver is

connected.

•Consult the dealer or an experienced radio/TV

technician

DOC ID - 1980 • Rev 01 3 / 3

for help. This device complies with Industry

Canada license-exempt RSS standard(s).

Operation is subject to the following two

conditions: (1) this device may not cause

interference, and (2) this device must accept any

interference, including interference that may

cause undesired operation of the device.Cet

appareil est conforme avec Industrie Canada

exempts de licence standard RSS (s). Son

fonctionnement est soumis aux deux conditions

suivantes: (1) cet appareil ne doit pas provoquer

d'interférences et (2) cet appareil doit accepter

toute interférence, y compris celles pouvant

causer un mauvais fonctionnement de l'appareil.

In accordance with FCC requirements of human

exposure to radio frequency fields, the radiating

element shall be installed such that a minimum

separation distance of 20 cm is maintained from

the general population.

FCC: 2ABBZ-RF-RDWS-433

IC: 11817A-RFRDWS433

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operation. Changes or

modifications not expressly approved by the party

responsible for compliance could void the user's

authority to operate the equipment. This Class B

digital apparatus complies with Canadian ICES-

3B. Cet appareil numérique de la classe B est

conforme à la norme NMB-003 du Canada.

MANUFACTURER HEREBY DISCLAIMS ALL

WARRANTIES AND REPRESENTATIONS,

WHETHER EXPRESS, IMPLIED, STATUTORY

OR OTHERWISE INCLUDING (BUT NOT

LIMITED TO) ANY WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE WITH RESPECT TO

THESE PRODUCTS AND ANY RELATED

SOFTWARE. MANUFACTURER FURTHER

DISCLAIMS ANY OTHER IMPLIED WARRANTY

UNDER THE UNIFORM COMPUTER

INFORMATION TRANSACTIONS ACT OR

SIMILAR LAW AS ENACTED BY ANY STATE.

(USA only) SOME STATES DO NOT ALLOW

THE EXCLUSION OF IMPLIED WARRANTIES,

SO THE ABOVE EXCLUSION MAY NOT APPLY

TO YOU. THIS WARRANTY GIVES YOU

SPECIFIC LEGAL RIGHTS AND YOU MAY

ALSO HAVE OTHER LEGAL RIGHTS THAT

VARY FROM STATE TO STATE.

MANUFACTURER MAKES NO

REPRESENTATION, WARRANTY, COVENANT

OR PROMISE THAT ITS ALARM PRODUCTS

AND/OR RELATED SOFTWARE (I) WILL NOT

BE HACKED, COMPROMISED AND/OR

CIRCUMVENTED; (II) WILL PREVENT, OR

PROVIDE ADEQUATE WARNING OR

PROTECTION FROM, BREAK-INS,

BURGLARY, ROBBERY, FIRE; OR (III) WILL

WORK PROPERLY IN ALL ENVIRONMENTS

AND APPLICATIONS.

Environmental

class

UL: Indoor dry

IEC: 3K5

EU compliance

EN 54

EN 54-00:0000

European Union

directives

1999/5/EC (R&TTE directive): Hereby, Clare

Controls declares that this device is in

compliance with the essential requirements and

other relevant provisions of Directive 1999/5/EC.

2002/96/EC (WEEE directive): Products marked

with this symbol cannot be disposed of as

unsorted municipal waste in the European Union.

For proper recycling, return this product to your

local supplier upon the purchase of equivalent

new equipment, or dispose of it at designated

collection points. For more information see:

www.recyclethis.info.

2006/66/EC (battery directive): This product

contains a battery that cannot be disposed of as

unsorted municipal waste in the European Union.

See the product documentation for specific

battery information. The battery is marked with

this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury

(Hg). For proper recycling, return the battery to

your supplier or to a designated collection point.

For more information see: www.recyclethis.info.

Warranty information

Clare Controls offers a two (2) year limited warranty on original

Clare Controls components, from the date of shipment from

Clare Controls.

Contact information

Clare Controls, LLC.

7519 Pennsylvania Ave, Suite 104

Sarasota, FL 34243

General: 941.328.3991

Fax: 941.870.9646

www.clarecontrols.com

Integrator/Dealer Support: 941.404.1072

cl[email protected]

Homeowner Support (ClareCare): 941.315.2273 (CARE)

[email protected]

Other clare Accessories manuals

clare

clare ClareOne CLR-C1-PNL1 Assembly instructions

clare

clare CLR-C1-ODDG Assembly instructions

clare

clare CVP-B3DB50-ODIW User manual

clare

clare ClareOne CLR-C1-ODDW Assembly instructions

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Siemens

Siemens QSA2700D Basic documentation

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

IFM Electronic

IFM Electronic Efector 250 Series Brief instructions

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual

clare CLR-C1-RCDW Assembly instructions

Popular Accessories manuals by other brands