Cissell WE176 User manual
Content
Contents
1 General safety instructions .............................................................. 3
2 Technical data and dimensions ....................................................... 4
Technical data ................................................................................ 4
Dimensions ..................................................................................... 5
3 Installation and connection ............................................................. 7
Ground ............................................................................................ 7
Anchoring ....................................................................................... 7
Water connection ............................................................................ 7
Water drain ..................................................................................... 8
Main power connection .................................................................... 8
Liquid soap connection ................................................................... 9
Connection of a central operating panel for coinmachines ............... 10
Steam connection ........................................................................... 11
4 Operating instructions ..................................................................... 12
Machine with start button ................................................................ 12
Machine with coin or token operation............................................... 21
5 Standard programs .......................................................................... 27
6 Technical remarks ............................................................................ 28
Internal connection of the electrical heating .................................... 28
Internal connections of the motor .................................................... 28
Thermo-magnetic motor protection .................................................. 29
Error messages .............................................................................. 29
7 Maintenance of the machine ........................................................... 31
Code: 249/00170/00
22/12/00
3
1
General safety instructions
Read the installation and instruction manual carefully before connecting the
machine.
It is recommended that the machine be installed by qualified technicians.
The machine should be installed according to the installation instructions.
(See chapter 4)
The machine should be grounded according to the instructions in order to
eliminate the risk of electrocution.
Do not expose the machine to high humidity or extreme high or low
temperatures.
Cut off all main water inlets, steam and electrical supplies at the end of each
operating day.
Before starting repairs or maintenance, shut off all power and water supplies.
To prevent fire and explosion:
Keep the area around the machine free from inflammable or combustible
products.
Do not put fabrics that are treated with inflammable products into the
machine. These fabrics should be hand-washed or air-dried first.
Always carefully read and follow the instructions on the packing of deter-
gents. Store these products out of the reach of children.
Always take into account the instructions on the labels of clothes.
Never allow children to play in the surroundings of a machine.
S
S
These instructions surely cannot prevent all risks of accidents. It is up to the user to act with the
utmost precaution.
Do not hesitate to contact the dealer in case of a problem.
Ignoring any of the safety instructions can cause serious
personal injury and can also cause damage to the linen or the
machine
S
S
S
S
S
S
S
S
S
S
S
Remark:
4
2
Technical data and dimensions
Technical data
WE 176 WE 234
Capacity (dry weight)
1/11 16 kg 21,3 kg
1/10 17,6 kg 23,4 kg
1/9 16,1 kg 26 kg
Cylinder
Diameter 750 mm 750 mm
Depth 399 mm. 530 mm
Volume 176 Lit. 234 Lit.
Cabinet
Height 1505 mm 1505 mm
Width 900 mm 900 mm
Depth 800 mm 930 mm
Front loading
Diameter door opening 395 mm 395 mm
Door height 510 mm 510 mm
To center 750 mm 750 mm
Speed
Wash 45 rpm
Spin 425 rpm
G-force
Spin 76
Motor(3 phase)
Wash 18p. 290rpm 280 W 400 W
Spin 2p. 2900 rpm 1300 W 2000W
Drain valve
Depend-O-Drain 3"
Water supply
Hard, soft, warm water and cool-down 3/4"
Steam connection
Steam connection 3/8"
Heating
Electrical 220/380 V 12/15/18 kW
Electrical 380 V 12/15/18/21/24 kW
Steam X
Warm water (without additional heating) X
Warm water (with additional heating) X
Packing dimensions
(H x W x D) 1105x975x1535 mm
Weight
Net 400 kg 435 kg
Gross 485 kg 500 kg
5
2
WE176
Dimensions
A. Hard water connection 3/4"
B. Warm water connection 3/4"
C. Soft water connection 3/4"
D. Electrical connection
E. Electrical connection clamps
F. Water drain
G. Steam connection
H. Ventilation soap dispenser
S
S
S
S
S
S
S
S
6
S
S
S
S
S
S
S
S
A. Hard water connection 3/4"
B. Warm water connection 3/4"
C. Soft water connection 3/4"
D. Electrical connection
E. Electrical connection clamps
F. Water drain
G. Steam connection
H. Ventilation soap dispenser
WE234
7
3
B
A
D
C
E
C
D
D
CG
B
A
E
F
The machine must be securely fixed on a flat surface (metal base, concrete or
solid ground). The anchoring is to be done on the provided places (A) in the base.
(See Dimensions 2)
The machine must be placed entirely level. For easy maintenance it is recom-
mended to keep a minimal distance of 600 mm between the wall and the back
of the machine.
If several machines are placed next to each another, there should be a minimal
distance of 30 mm between each machine.
Installation and connection
Surface
Anchoring
Water connection
The machine must be anchored directly on a concrete base.
Directly on the ground
The machines must be fixed on a metal base which is securely anchored on a
concrete base.
On a metal base
A: Bolt M16
B: Concrete base 40cm
C:Washer40x17x4
D: Nut M16
E: Base of the machine
F: Metal base
A: Bolt M16
B: Concrete base 40cm
C:Washer40x17x4
D: Nut M16
The machine is delivered with hoses with 3/4" connections. These hoses fit the
water inlet valves of the machine and the main water inlet taps. To ensure the
optimal functioning of the water inlet valves, the water pressure on the inlet should
be between 0,5 and 10 kg/cm² (7 and 145 psi). If the pressure is too low, the cycle
time will increase considerably.
In case of boiler fed machines, a minimum of hot water of 90°C should be available.
For the WE 176: 125l.
For the WE 234: 150l.
8
3
Remove the cover plate at the back of the machine. (See dimensions (E)).
Connect the power cable to the connectors.
220V 3AC
220V 3 phase (3AC) should be connected to the connectors “L1,L2,L3”.
The green/yellow grounding clamp has to be connected to the grounding
wire “PE”.
380 V 3AC + N
380 V 3 phase (3AC + N) has to be connected to the connectors
“L1,L2,L3”, the blue neutral to the “N” connector.
The green/yellow grounding clamp has to be connected to the groun-
ding wire “PE”.
After connection, check the spin direction. The cylinder must spin in
the direction of the arrow, showed on the sticker on the door window
(clockwise).
A wrong spin direction can damage the motor, and can also cause water
to spurt from the soap dispenser.
In case of wrong spin direction: switch the terminal clamps of the motor
circuit “R” and “S” of the connecting cable.
The diameter of the main drain should be adapted to the water flow and
the number of machines. It should be sufficient to handle at least 160L/
min. per machine.
It is necessary to connect the main drain at least on one side to an open
air-brake to allow ventilation.
The machine is equipped with a drain valve with 3" outer diameter (80 mm).
This drain valve should be connected to the drain by means of the drain
elbow which is delivered with the machine.
S
S
Main power connection
Water drain
S
S
S
Power of the breaker plugs: machine with steam heating or boiler fed machines without additio-
nal electrical heating
Heating: 220V3AC 380V3AC + N
12 kW 40 A 20 A
15 kW 50 A 25 A
18 kW 50 A 32 A
21 kW ---- 40 A
24 kW ---- 40 A
machine with electrical heating
220V 3AC 380V 3AC + N
16 A 16 A
S
9
3
With an external tension 24V DC
Electrical connection of
the liquid soap pumps
On machines equipped with a liquid soap connection, connect the wires
directly on the print board next to the ground wire connection (option).
Connect as indicated on the wiring diagram.
The two connectors on the right give a tension of 220V ~ (max. 4A) which
can be applied to drive 220V ~ soap pumps. If more than 4A is required,
an external tension will have to be used. 6 connections have been
provided, of which one (S6) can be used to drive a waterproofing pump
(e.g. for rain coats, etc.).
The 220V can be transformed to other values to drive other type soap
pumps.
Example: pumps 24V ~.
Also, pumps with different operating tension can be combined.
Example: 5 pumps 220V ~ and 1 pump 24V ~.
A rubber connection has been placed over the air break opening at the back
of the machine. There are 5 holes in this rubber connection, through each
of which a liquid soap hose can be driven (S1...S5). Press the hoses until
they appear well inside the soap dispenser.
The central gap in the rubber connection remains and serves as air breaker.
Liquid soap connection (option)
Connection of the liquid soap
hoses
10
3
A
Connection of a central operating
panel for coinmachines (option)
At the backside above the main connectors, you find a printboard, to which the
central operating panel for coinmachines can be connected.
The right connectors form a potential free output contact as a result of which the
operating
panel detects when the machine is activated or not.
The left connectors receive the signal, by means of which a machine is chosen
through the operating panel.
There are 3 different variations possible according to the output voltage of the
operating panel.
Remark :
If a machine is equipped with this kind of printboard or if a printboard
has been built in, the resistance of the cycle contact (A) may no longer
be present on the main printboard.
When this resistance is present, it has to be cut out of the main
printboard.
This manual suits for next models
1
Table of contents
Other Cissell Washer manuals
Cissell
Cissell CHMW35-WE55-165 User manual
Cissell
Cissell 40-175 lb User manual
Cissell
Cissell IPSO HF234 User manual
Cissell
Cissell CHHW50-WE176-234 User manual
Cissell
Cissell CHMW35-WE110-132-165 Guide
Cissell
Cissell CSHW35-HW55-164 User manual
Cissell
Cissell CSHW50-HF135-234 User manual
Cissell
Cissell CSHW35-HW131-164 Guide
Cissell
Cissell CHHW50-WE234 Guide
Cissell
Cissell CT055 User manual
Popular Washer manuals by other brands
Tricity Bendix
Tricity Bendix AW 1000 W Operating & installation instructions
Panasonic
Panasonic NA-F60L5WRB operating instructions
GE
GE WSLP1500 Dimensions and installation information
Electrolux
Electrolux EWF1284EDW Service manual
Bosch
Bosch WAN2829BSN User manual and installation instructions
LG
LG TV2516DV3B owner's manual
