Cisco Nexus 93108TC-FX3P Manual
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation
Guide
First Published: 2021-02-01
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
©2021 Cisco Systems, Inc. All rights reserved.
CONTENTS
Overview 1
CHAPTER 1
Overview 1
Preparing the Site 5
CHAPTER 2
Temperature Requirements 5
Humidity Requirements 5
Altitude Requirements 5
Dust and Particulate Requirements 6
Minimizing Electromagnetic and Radio Frequency Interference 6
Shock and Vibration Requirements 7
Grounding Requirements 7
Planning for Power Requirements 7
Airflow Requirements 9
Rack and Cabinet Requirements 9
Clearance Requirements 10
Installing the Switch Chassis 13
CHAPTER 3
Safety 13
Installation Options with Rack-Mount Kits 14
Airflow Considerations 14
Installation Guidelines 14
Unpacking and Inspecting the Switch 16
Installing the Switch Using the NXK-ACC-KIT-1RU Rack-Mount Kit 16
Installing the Switch into a Two-Post Rack Using the NXK-ACC-KIT-1RU Rack-Mount Kit 20
Grounding the Chassis 23
Starting the Switch 24
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
iii
Connecting the Switch to the ACI Fabric 27
CHAPTER 4
ACI Fabric Topology 27
Preparing to Connect to Other Devices 28
Connecting Leaf Switches to APICs 29
Connecting Leaf Switches to Spine Switches 31
Installing a Gigabit Ethernet module (GEM) 32
Virtual Port Channel Migration - Migration of Nodes from a First-Generation Switch to a
Second-Generation Switch 32
Setting Up an Optional Console Interface 33
Setting Up an Optional Management Connection 34
Optic Transceiver Removal Using the Optics Extraction Tool 34
Maintaining Transceivers and Optical Cables 36
Replacing Components 37
CHAPTER 5
Replacing a Power Supply Module 37
Replacing an AC Power Supply 37
Rack Specifications 39
APPENDIX A
Overview of Racks 39
General Requirements for Cabinets and Racks 39
Requirements Specific to Standard Open Racks 40
Requirements Specific to Perforated Cabinets 40
Cable Management Guidelines 40
System Specifications 41
APPENDIX B
Environmental Specifications 41
Switch Dimensions 41
Switch and Module Weights and Quantities 42
Transceiver and Cable Specifications 42
Switch Power Input Requirements 42
Power Specifications 43
1100-W AC Power Supply Specifications 43
1900-W AC Power Supply Specifications 43
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
iv
Contents
Power Cable Specifications 44
Power Cables for NXA-PAC-1100W Power Supplies 44
Regulatory Standards Compliance Specifications 45
LEDs 47
APPENDIX C
Switch Chassis LEDs 47
Fan Module LEDs 48
Power Supply LEDs 48
Additional Kits 49
APPENDIX D
Rack Mount Kit NXK-ACC-KIT-1RU 49
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
v
Contents
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
vi
Contents
CHAPTER 1
Overview
•Overview, on page 1
Overview
The Cisco Nexus 93108TC-FX3P switch (N9K-C93108TC-FX3P) is a 1-rack unit (RU), fixed-port switch
designed for spine-leaf-APIC deployment in data centers. PoE is supported on ports 1-48. This switch supports
the following ports:
• 48 100M/1/2.5/5/10GBASE-T ports (ports 1-48).
• 6 40/100-Gigabit ports QSFP28 (ports 49-54)
• Two management ports (one 10/100/1000BASE-T port and one SFP port)
• One console port (RS-232)
• 1 USB port
This switch includes the following user-replaceable components:
• Fan modules (four) with the following airflow choices:
• Port-side exhaust fan module with blue coloring (NXA-FAN-35CFM-PE)
• Port-side intake fan module with burgundy coloring (NXA-FAN-35CFM-PI)
This switch runs with +1 redundancy mode, so that if one fan fails, the switch
can sustain operation. But if a 2nd fan fails, this switch is not designed to sustain
operation. Hence before waiting for major threshold temperature to be hit, the
switch will power down due to Powered-down due to fan policy trigger.
Note
• Power supply modules (two—One for operations and one for redundancy [1+1]) with the following
choices:
• 1100-W port-side exhaust AC power supply with blue coloring (NXA-PAC-1100W-PE)
• 1100-W port-side intake AC power supply with burgundy coloring (NXA-PAC-1100W-PI)
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
1
• 1900-W port-side intake AC power supply with burgundy coloring (NXA-PAC-1900W-PI)
All fan modules and power supplies must use the same airflow direction.
Note
This switch may present access issues if installed between switches with greater
chassis depth. Please consider this before installation.
Note
The following figure shows the switch features on the port side of the chassis.
6 40/100-Gigabit QSFP28
ports
3BCN, STS, ENV, and P
LEDs
1
48 100M/1/2.5/5/10GT
ports
2
To determine which transceivers, adapters, and cables are support this switch, see the Cisco Transceiver
Modules Compatibility Information document.
The following figure shows the switch features on the power supply side of the chassis.
Management port
(1—SFP optical port)
4Fan modules (4) with slots
numbered from 1 (left) to
4 (right)
1
USB port (1)5Console port (1)2
Power supply modules (1
or 2) (AC power supplies
shown) with slots
numbered 1 (left) and 2
(right)
6Management port
(1—RJ-45 copper port)
3
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
2
Overview
Overview
The following figure shows the side of the chassis.
Grounding pad3Screw holes formounting
brackets
1
Depending on whether you plan to position the ports in a hot or cold aisle, you can order the fan and power
supply modules with port-side intake or port-side exhaust airflow. For port-side intake airflow, the fan and
power supplies have burgundy coloring. For port-side exhaust airflow, the fan and power supplies have blue
coloring.
The fan and power supply modules are field replaceable. You can replace one fan module or one power supply
module during operations so long as the other modules are installed and operating. If you have only one power
supply installed, you can install the replacement power supply in the open slot before removing the original
power supply.
All fan and power supply modules must have the same direction of airflow. Otherwise, the switch can overheat
and shut down.
Note
If the switch has port-side intake airflow (burgundy coloring for fan modules), you must locate the ports in
the cold aisle. If the switch has port-side exhaust airflow (blue coloring for fan modules), you must locate the
ports in the hot aisle. If you locate the air intake in a hot aisle, the switch can overheat and shut down.
Caution
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
3
Overview
Overview
Cisco Nexus 93108TC-FX3P ACI-Mode Switch Hardware Installation Guide
4
Overview
Overview
Other manuals for Nexus 93108TC-FX3P
2
This manual suits for next models
1
Table of contents
Other Cisco Switch manuals
Cisco
Cisco Nexus 9332D-GX2B Manual
Cisco
Cisco SR2024 - Small Business Unmanaged Switch User manual
Cisco
Cisco MS225-24 User manual
Cisco
Cisco 2950-12 - Catalyst Switch User manual
Cisco
Cisco Catalyst Express 520 User manual
Cisco
Cisco AJ732A - MDS 9134 Fabric Switch Instruction Manual
Cisco
Cisco DS-C9216I-K9 User manual
Cisco
Cisco Catalyst 2900 Series Manual
Cisco
Cisco 3020 - Cisco Catalyst Blade Switch Instruction Manual
Cisco
Cisco BPX-BXM-T3-12 User manual
Cisco
Cisco MDS 9500 Series User manual
Cisco
Cisco Nexus 5000 Series User manual
Cisco
Cisco 3750 - Catalyst EMI Switch Instruction sheet
Cisco
Cisco NMD-36-ESW= Dimensions
Cisco
Cisco Cisco mds 9216 - fabric switch Manual
Cisco
Cisco 3020 - Cisco Catalyst Blade Switch Instruction Manual
Cisco
Cisco SG 100D-08 User manual
Cisco
Cisco Catalyst 3000 Original instructions
Cisco
Cisco Nexus 9336C-FX2-E Manual
Cisco
Cisco ME 3400 Series User manual
