Cisco Catalyst 9600 Series User manual
Installing the Switch
•Unpacking the Switch, on page 1
•Install the Switch as Shipped, on page 2
•Install the Switch with Shelf Brackets, on page 8
•Install the Switch in NEBS-Compliant Mode, on page 22
•Establishing System Ground, on page 29
•Attaching an ESD Strap, on page 32
•Verifying the Switch Chassis Installation, on page 33
Unpacking the Switch
Check the contents of the shipping container:
Procedure
Step 1 Check the contents of the accessory kit. Verify that you have received all the listed equipment, including any
optional equipment you may have ordered, such as, network interface cables, transceivers, or special connectors.
Step 2 Check the modules in each slot. Ensure that the configuration matches the packing list and that all of the
specified interfaces are included.
Step 3 Store the shipping carton.
Do not discard the shipping container when you unpack the switch. Flatten the shipping cartons and
store them with the pallet. You will require these containers if you have to move or ship the switch
in the future.
Tip
Installing the Switch
1
Install the Switch as Shipped
Installing the Cable Guide on the Chassis with L-Brackets Preinstalled on the
Chassis
Procedure
Step 1 Position the cable guides to align with the L-brackets preinstalled on the chassis and secure the cable guides
to the L-brackets using the screws provided.
Figure 1: Attaching the Cable Guides
Cable guides2Screws to attach the cable guides to the
L-brackets on the chassis
1
Step 2 Secure the chassis to the rack rails with four screws on each side.
Installing the Switch
2
Installing the Switch
Install the Switch as Shipped
Figure 2: Mounting the Chassis to the Rack
Cable guide installed2Screws to attach the chassis to the rack post1
Cable guide installation is complete.
Installing the Switch
3
Installing the Switch
Installing the Cable Guide on the Chassis with L-Brackets Preinstalled on the Chassis
Figure 3: Chassis with Cable Guide Attached
Rack-Mounting the Chassis as Shipped
This procedure shows how to rack mount the chassis as shipped.
Installing the Switch
4
Installing the Switch
Rack-Mounting the Chassis as Shipped
Before you begin
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to
ensure that the system remains stable. The following guidelines are provided to ensure your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the
heaviest component at the bottom of the rack.
If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the
unit in the rack.
Statement 1006
Warning
Procedure
Step 1 Insert the rear of the chassis between the mounting posts of the rack.
Step 2 Align the mounting holes in the L bracket on the switch or on the cable mount (if installed) with the mounting
holes in the equipment rack.
Installing the Switch
5
Installing the Switch
Rack-Mounting the Chassis as Shipped
Figure 4: Securing the Chassis to the Rack Posts
Cable guides210-32 or 12-24 pan head screws1
Step 3 Secure the chassis to the rack with either 10-32 or 12-24 pan head screws from the chassis standard accessory
kit.
Installing the Switch
6
Installing the Switch
Rack-Mounting the Chassis as Shipped
Figure 5: Chassis Secured to the Rack Posts
Step 4 4. Use a tape measure and level to ensure that the chassis is installed straight and level..
What to do next
After installing the chassis in its location, complete the installation process by:
1. Connecting the chassis to system ground.
2. Installing and connecting the power supplies to the power source.
3. Connecting the network interface cables to the supervisor module and line card modules. This may involve
installing transceivers before you attach the network interface cables.
Installing the Switch
7
Installing the Switch
Rack-Mounting the Chassis as Shipped
4. Powering up the chassis and verifying the installation.
Install the Switch with Shelf Brackets
Installing the Shelf Kit L-Brackets
The switch chassis is shipped with two L-brackets installed on the front sides of the chassis. If you are
rack-mounting the switch using the shelf kit, these L-brackets must be removed and replaced with L-brackets
that are part of the shelf kit.
Before you begin
You have ordered and received the shelf kit.
Procedure
Step 1 Remove and discard the L-brackets and the ten mounting screws that the chassis is shipped with. Do not re-use
them during any part of the installation process.
Installing the Switch
8
Installing the Switch
Install the Switch with Shelf Brackets
Figure 6: L-Brackets the Chassis is Shipped with
Right L-bracket2Left L-bracket1
Installing the Switch
9
Installing the Switch
Installing the Shelf Kit L-Brackets
Figure 7: Removing L-Brackets the Chassis is Shipped With
--Mounting screws the chassis is shipped with1
Installing the Switch
10
Installing the Switch
Installing the Shelf Kit L-Brackets
Other manuals for Catalyst 9600 Series
3
Table of contents
Other Cisco Switch manuals
Cisco
Cisco Meraki MS250 Series User manual
Cisco
Cisco Catalyst 3750-X Series User manual
Cisco
Cisco Catalyst 3650 Series User manual
Cisco
Cisco MDS 9120 - Fabric Switch Operation and maintenance manual
Cisco
Cisco Small Business 200 Series Instruction Manual
Cisco
Cisco SG300-52P-K9-NA User manual
Cisco
Cisco SD205 User manual
Cisco
Cisco MDS 9132T User manual
Cisco
Cisco 4900M - Catalyst Switch User manual
Cisco
Cisco Catalyst X4424 User manual
Cisco
Cisco MDS 9700 Series Manual
Cisco
Cisco 3750 - Catalyst EMI Switch Installation manual
Cisco
Cisco SF250-24 User manual
Cisco
Cisco Nexus 93240YC-FX2 Manual
Cisco
Cisco Catalyst 3120G User instructions
Cisco
Cisco BPX 8600 Series User manual
Cisco
Cisco Nexus 9358GY-FXP Manual
Cisco
Cisco SPS208G User manual
Cisco
Cisco Catalyst 4500 Series Instruction Manual
Cisco
Cisco Nexus 5000 Series User manual
