Cisco Catalyst 3032 User manual

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

OL-14317-01

Cisco Catalyst Blade Switch

3130 for Dell and Cisco Catalyst Blade

Switch 3032 for Dell

Getting Started Guide

This guide provides instructions on how to install the Cisco Catalyst Blade Switch

3130 for Dell and the Cisco Catalyst Blade Switch 3032 for Dell—both hereafter

referred to as the switch—in the Dell Modular Server Chassis and how to set up

and configure your switch. The Dell Modular Server Chassis—hereafter referred

to as the server chassis—is a system that supports up to sixteen server modules

and up to six Ethernet switches. You install the switch in one of the chassis I/O

module bays on the rear panel of the server chassis.

Also covered in this guide are switch management options and troubleshooting

help for the switch.

For details on the number, types, and the location of the module bays and for

additional information on the entire modular server system, see the

documentation for the Dell PowerEdge Systems at www.support.dell.com.

For additional installation and configuration information about the switch, see the

Cisco Catalyst Blade Switch 3000 Series for Dell documentation on Cisco.com.

For system requirements, important notes, limitations, open and resolved caveats,

and last-minute documentation updates about the switch, see the release notes,

also on Cisco.com.

When you use the online publications, refer to the documents that match the Cisco

IOS software version that is running on the switch.

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

Contents

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

OL-14317-01

For translations of the warnings that appear in this publication, see the Regulatory

Compliance and Safety Information for the Cisco Catalyst Blade Switch 3000

Series for Dell that accompanies this guide.

Note Before proceeding, read the release notes for the server chassis. The release notes

are available on the Dell support website at www.support.dell.com.

Contents

•Taking Out What You Need, page 3

•Switch Description, page 3

•Dell Modular Server Chassis Architecture, page 6

•Installation Warning Statements, page 7

•Installing the Switch in the Server Chassis, page 8

•Configuring the Switch, page 12

•Managing the Switch, page 20

•Planning and Creating a Switch Stack (Only 3130G-S and 3130X-S

Switches), page 22

•Connecting to the Switch Ports, page 26

•In Case of Difficulty, page 28

•Obtaining Documentation, Obtaining Support, and Security Guidelines,

page 30

•Hardware Warranty Terms, page 31

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

OL-14317-01

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

Taking Out What You Need

These items ship with your switch:

Follow these steps:

1. Unpack and remove the switch and the accessory kit from the shipping box.

2. Return the packing material to the shipping container, and save it for

future use.

Note If you order the switches with the server chassis, the switches are already

installed, and no unpacking is required. The unpacking procedure applies only if

you order a switch.

Switch Description

These are the available switch models:

250289

Documentation

STK

17X

18X

19X

20X

X2-1

X2-2

WS-CBS3130X-S

CONSOLE

MODE

Product

Documentation

Model Description

CBS3032G 1-Gigabit Ethernet nonstacking-capable switch

CBS3130G-S 1-Gigabit Ethernet stacking-capable switch

CBS3130X-S 10-Gigabit Ethernet stacking-capable switch

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

Switch Description

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

OL-14317-01

The switch runs the universal software image that has the Cisco IOS code for

multiple feature sets. To enable a specific feature set, you must use the software

activation feature to install the software license for that feature set. For more

information, see the Cisco Software Activation Document for Dell, the release

notes, and the software configuration guide on Cisco.com.

Figure 1 shows the Cisco Catalyst Blade Switch 3130 for Dell as an example.

The other switch models have similar components.

Figure 1 Switch Front Panel

For more information about the LEDs and their meanings, see the switch

hardware installation guide on Cisco.com.

1Switch 8Release latch

2StackWise Plus ports A and B (supported

only on the 3130G-S and 3130X-S

switches)

9Cisco status LEDs

3Gigabit Ethernet uplink ports 17 to 20 10 System Status/ID LED

4LEDs for ports 21 and 22 11 Mode button

510-Gigabit Ethernet slot 1

or Gigabit Ethernet ports 21 and 22

12 Console port

6LEDs for ports 23 and 24 13 Power LED

710-Gigabit Ethernet slot 2

or Gigabit Ethernet ports 23 and 24

STK

17X

18X

19X

20X

X2-1

X2-2

WS-CBS3130X-S

CONSOLE

MODE

250198

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

OL-14317-01

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

Switch Description

Table 1 describes the switch ports.

Each port has an associated LED. The System Status/ID LED is controlled

by the Dell Remote Access Controller/Modular Chassis (DRAC/MC)

management board.

For a list of supported modules, see the release notes on Cisco.com. For detailed

instructions on installing, removing, and connecting to SFP modules, see the

documentation that came with the SFP module.

Table 1 Cisco Catalyst Blade Switch 3130 for Dell and 3032 for Dell Port Descriptions

Port Description

Ports 1 to 16 Internal Gigabit Ethernet 1000BASE-X downlink ports that connect the switch

to the server chassis blades.

Ports 17 to 20 External 10/100/1000BASE-T copper Gigabit Ethernet uplink ports that support

auto-MDIX, and autonegotiation.

Ports 21 to 24 10-Gigabit Ethernet module slots for use with the Cisco TwinGig Converter

Modules and Cisco X2 transceiver modules.

Internal

100BASE-T

Ethernet port

The internal 100BASE-T Ethernet port (Fa0) is used only for switch management

traffic, not for data traffic. It is connected to the Dell management console

through the server chassis backplane connector. Traffic to and from this port is

isolated from the switch ports.

Console port Switch management serial port that uses an RJ-45 connector.

StackWise Plus

ports

Stacking cable ports (supported only on the 3130G-S and 3130X-S switches).

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

Dell Modular Server Chassis Architecture

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

OL-14317-01

Dell Modular Server Chassis Architecture

The six chassis I/O module bays are on the rear panel (see Figure 2).

Figure 2 Dell Modular Server Chassis Rear Panel

!!!!!!

250199

WS-CBS3130X-S

STK

17X

18X

19X

20X

X2-1

X2-2

CONSOLE

MODE

345

789

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

OL-14317-01

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

Installation Warning Statements

For more information about the components of the information panel, see the Dell

documentation at www.support.dell.com.

Installation Warning Statements

This section includes the basic installation warning statements. Translations of

these warning statements appear in the Regulatory Compliance and Safety

Information for the Cisco Catalyst Blade Switch 3000 Series for Dell document

that shipped with the switch.

Warning

To prevent the switch from overheating, do not operate it in an area that

exceeds the maximum recommended ambient temperature of 113°F (45°C). To

prevent airflow restriction, allow at least 3 inches (7.6 cm) of clearance around

the ventilation openings.

Statement 17B

Warning

Class 1 laser product.

Statement 1008

Warning

Only trained and qualified personnel should be allowed to install, replace, or

service this equipment.

Statement 1030

1Dell server chassis 7I/O module C2

2Primary CMC1module

1. CMC: Chassis Management Controller.

8I/O module B2

3Switch installed in I/O module A1 9I/O module A2

4I/O module B1 10 Secondary CMC module2

2. This module is optional.

5I/O module C1 11 Fan modules

6Optional iKVM3module

3. iKVM: integrated keyboard video mouse.

12 Power supplies

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

Installing the Switch in the Server Chassis

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

OL-14317-01

Warning

Ultimate disposal of this product should be handled according to all national

laws and regulations.

Statement 1040

Warning

For connections outside the building where the equipment is installed, the

following ports must be connected through an approved network termination

unit with integral circuit protection: 10/100/1000 Ethernet.

Statement 1044

Warning

Installation of the equipment must comply with local and national electrical

codes.

Statement 1074

Installing the Switch in the Server Chassis

Before you install the switch in the server chassis, consider these points:

•Review and become familiar with the safety and handling guidelines

specified in the Product Information Guide.

•Review the Regulatory Compliance and Safety Information for the Cisco

Catalyst Blade Switch 3000 Series for Dell that ships with this product.

•If you plan to create a switch stack, review the “Planning and Creating a

Switch Stack (Only 3130G-S and 3130X-S Switches)” section on page 22

before you install the switch and run the initial configuration setup program.

•To help ensure proper cooling and system reliability, keep these points

in mind:

–

Each chassis I/O module bay must contain either a module or an

input/output module (IOM) blank.

–

When you remove a hot-swap module, you must replace it with an

identical module or an IOM blank within 1 minute of removal.

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

OL-14317-01

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

Installing the Switch in the Server Chassis

–

You can install the switch into any of the module slots. If you install a

switch in the B or C module slot, the Ethernet mezzanine card must be

installed in the blade server.

–

The dust covers should always remain in place unless a module is

installed in the slot.

Caution To prevent electrostatic-discharge (ESD) damage when you install the switch,

follow your normal board and component handling procedures.

Note When you install a switch, you do not need to power down the server chassis.

The initial configuration assumes that the switch was never configured, that it is

in the same state as when it was received, and that it is not configured with a

default username and password.

Follow these steps to install the switch into the server chassis:

Step 1 Obtain and make note of this information from your network administrator before

you begin the switch installation:

•Switch IP address

•Subnet mask (IP netmask)

•Default gateway (router)

•Enable secret password (encrypted)

•Enable password (not encrypted)

•Telnet password

•SNMP community strings (optional)

Step 2 Select a chassis I/O module bay in which to install the switch. Follow the

prerequisites listed in the “Dell Modular Server Chassis Architecture” section on

page 6.

Step 3 Remove the IOM blank from the selected bay, and store it for future use.

Step 4 If you have not already done so, touch the static-protective package that contains

the switch to an unpainted metal part of the server chassis for at least 2 seconds.

Step 5 Remove the switch from its static-protective package.

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

Installing the Switch in the Server Chassis

Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting Started Guide

OL-14317-01

Step 6 Ensure that the release latch on the switch is in the open position or perpendicular

to the module (see Figure 3):

Figure 3 Release Latch in Open Position

Step 7 Slide the switch into the appropriate bay until it stops.

Step 8 Push the release latch on the front of the switch to the closed position.

250200

WS-CBS3130X-S

STK

17X

18X

19X

20X

X2-1

X2-2

CONSOLE

MODE

Other manuals for Catalyst 3032

This manual suits for next models

Table of contents

Other Cisco Switch manuals

Cisco

Cisco AJ732A - MDS 9134 Fabric Switch Instruction Manual

Cisco

Cisco Business 250 Series User manual

Cisco

Cisco MDS 9132T User manual

Cisco

Cisco AS-2000 User manual

Cisco

Cisco MDS 9222i - Multiservice Modular Fabric... How to use

Cisco

Cisco Catalyst 2924M XL User manual

Cisco

Cisco SRW2008MP Quick start guide

Cisco

Cisco S 300 Series User manual

Cisco

Cisco Catalyst 2960 Series User manual

Cisco

Cisco Nexus 9508 NX-OS Manual

Cisco

Cisco SGE2000 - Cisco - Gigabit Switch Instruction Manual

Cisco

Cisco SGE2000 User manual

Cisco

Cisco 2950 - Catalyst Switch Installation manual

Cisco

Cisco Nexus 5000 Series User manual

Cisco

Cisco SLM2005 - Small Business Smart Switch User manual

Cisco

Cisco Catalyst 3120 Manual

Cisco

Cisco NMH Series User manual

Cisco

Cisco MDS 9000 Series Instruction Manual

Cisco

Cisco 3750 - Catalyst EMI Switch Instruction sheet

Cisco

Cisco Nexus 9236C User manual

Cisco

Cisco Nexus 3000 series User manual

Cisco

Cisco Nexus 9332PQ User manual

Cisco

Cisco Catalyst 6840 Series Manual

Cisco

Cisco Catalyst 3750G-12S-SD How to use

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual