Cisco Network Assistant User manual

CHAPTER

3-1

Getting Started with Cisco Network Assistant

OL-6194-02

Installing, Launching, and Connecting Network

Assistant

This chapter describes what you need to install Network Assistant, how to install it, how to launch it,

and how to connect it to a device or an existing community.

Installation Requirements

The PC on which you install Network Assistant must meet these minimum requirements:

•Processor speed: 1 GHz

•DRAM: 256 MB

•Hard-disk space: 200 MB recommended (the actual application requires around 70 MB)

•Number of colors: 65536

•Resolution: 1024 x 768

•Font size: Small

Network Assistant is supported on these operating systems:

•Windows XP, Service Pack 1 or later

•Windows 2000, Service Pack 3 or later

•Windows NT 4.0, Service Pack 6 or later

•Windows 98, second edition

Note Network Assistant on Windows 98 cannot manage Catalyst 4500 series switches.

Installing Network Assistant

To install Network Assistant on your PC, follow these steps:

1. Go to this web address: http://www.cisco.com/go/NetworkAssistant.

You must be a registered Cisco.com user, but you need no other access privileges.

2. Find the Network Assistant installer, cna-windows-k9-installer.2-0.exe.

3-2

Getting Started with Cisco Network Assistant

OL-6194-02

Chapter 3 Installing, Launching, and Connecting Network Assistant

Launching Network Assistant

3. Download the Network Assistant installer, and run it. (You can run it directly from the web if

your browser offers this choice.)

Network Assistant is free—there is no charge to download, install, or use it.

When you run the installer, follow the displayed instructions. In the final panel, click Finish to

complete the Network Assistant installation.

Launching Network Assistant

After Network Assistant is installed, you see its icon on your desktop, a Network Assistant entry under

Start > Programs, and a Network Assistant executable file in the installation directory. When you click

any of these, you see a partial Network Assistant GUI and the Connect window.

In disconnect mode, Network Assistant is not connected to a device or a community; it cannot manage

a standalone device, a community, or the command device of a cluster. Its menu bar and toolbar support

only the tasks that customize Network Assistant itself. The feature bar, which usually lists device

features, is empty.

Connecting Network Assistant to a Community or a Cluster

To connect Network Assistant to a device, use the Connect window shown in Figure 3-1. In it, enter the

IP address of the device to which you want to connect. For an existing community, select its name from

the pull-down menu. For an existing cluster, you select the IP address. Click Options if you want to

•Communicate with the device by using HTTPS (secure HTTP) instead of HTTP (clusters only).

Note Catalyst 4500 series switches do not support HTTPS. You must enable HTTP.

•Use an HTTP port other than 80 on the device (clusters only).

•Connect with read-only access.

For instructions on how to use the Connect to a new community option to create a community, see the

“Creating a Community” section on page 4-4. When you click Connect, you are either connected to the

community directly, or you are prompted for a username and password and then connected. When you

connect to a cluster, Network Assistant asks if you want to convert the cluster to a community. For more

information on converting a cluster to a community, see the “Converting a Cluster to a Community”

section on page 4-5.

Figure 3-1 Connect Window

3-3

Getting Started with Cisco Network Assistant

OL-6194-02

Chapter 3 Installing, Launching, and Connecting Network Assistant

Connecting Network Assistant to a Community or a Cluster

When the connection occurs, the Network Assistant window is in connect mode. The toolbar adds icons

that represent device features. Similarly, the feature bar fills with menus that list the device features that

Network Assistant manages.

Access Modes in Network Assistant

When you select a community to manage, you can set the access mode and access level. If you do not

set the access mode before connecting to the community, Network Assistant applies the read-write

default access mode to all of the devices in the community.

3-4

Getting Started with Cisco Network Assistant

OL-6194-02

Chapter 3 Installing, Launching, and Connecting Network Assistant

Connecting Network Assistant to a Community or a Cluster

Other manuals for Network Assistant

This manual suits for next models

Table of contents

Other Cisco Software manuals

Cisco

Cisco TELEPRESENCE MANAGEMENT SUITE SECURE SERVER - CONFIGURATION GUIDE... User manual

Cisco

Cisco 6503-E - Catalyst Chassis With Supervisor Engine 32... Instruction Manual

Cisco

Cisco Unified MeetingPlace H.323/SIP Service manual

Cisco

Cisco 5520 - ASA IPS Edition Bundle User manual

Cisco

Cisco 4700M User manual

Cisco

Cisco OL-10426-01 User manual

Cisco

Cisco 861W - Integrated Services Router Wireless User manual

Cisco

Cisco ACTIVE NETWORK ABSTRACTION - BROCHURE WHATS NEW IN RELEASE... User manual

Cisco

Cisco 4700M Instruction Manual

Cisco

Cisco Signaling Interface H.323 User manual

Cisco

Cisco Unified Contact Center Express User manual

Cisco

Cisco IPICS User manual

Cisco

Cisco 3600 Series User manual

Cisco

Cisco UC520-24U-8FXO-K9 Installation guide

Cisco

Cisco WS-SUP32-GE-3B - Supervisor Engine 32 User manual

Cisco

Cisco IP Communicator User manual

Cisco

Cisco TELEPRESENCE MANAGEMENT SUITE EXTENSION 2.2 - FOR MICROSOFT... Service manual

Cisco

Cisco Nexus 7000 Series Guide

Cisco

Cisco CISCO1811 User manual

Cisco

Cisco CONFERENCING EXTENSIONS - FOR MICROSOFT EXCHANGE... User manual

Cisco

Cisco Catalyst Series Switch 2940 User manual

Cisco

Cisco TELEPRESENCE MANAGEMENT SUITE EXTENSION 2.2 - FOR MICROSOFT... User manual

Cisco

Cisco OL-6900-01 Operator's manual

Cisco

Cisco XO User manual

Popular Software manuals by other brands

COMPRO

COMPRO COMPROFM manual

Muratec

Muratec OFFICEBRIDGE ONLINE user guide

Oracle

Oracle Contact Center Anywhere 8.1 installation guide

Adobe

Adobe 65007312 - Photoshop Lightroom Programmer's guide

Avaya

Avaya NULL One-X for RIM Blackberry user guide

HP ProLiant BL420c user guide

PS Audio

PS Audio PowerPlay Programming manual

Brady

Brady LOCKOUT PRO 3.0 Administrator's guide

Avaya

Avaya Interaction Center user guide

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Guide book

Novell

Novell GROUPWISE 8 - INTERNET AGENT manual

Oracle

Oracle Application 9i Configuration guide

Acer

Acer RDM user guide

Canon

Canon Vixia HF21 instruction manual

Canon

Canon ZR950 instruction manual

Samsung

Samsung Auto Backup user manual

Polycom

Polycom Vortex EF2201 Application note

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c user manual