Cisco 3600 Series Quick start guide
1
Doc. No.
Cisco Systems, Inc.
All rights reserved.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Cisco Systems, Inc.
Corporate Headquarters
Copyright © 1996
Cisco 3600 Series Rack-Mount and Wall-Mount
Configuration Note
Product Numbers:
ACS-3620RM-19=, ACS-3620RM-24=, ACS-3640RM-19=, ACS-3640RM-24=
CPAACS-3620RM-19=, CPAACS-3620RM-24=, CPAACS-3640RM-19=,
CPAACS-3640RM-24=
This document describes how to rack-mount or wall-mount a Cisco 3620 or Cisco 3640 router.
Note In this document, the term “Cisco 3600 series” refers to the Cisco 3620 and Cisco 3640
routers.
Use this document in conjunction with your router installation and configuration guide and the
Regulatory Compliance and Safety Information document for your router.
If you have questions or need help, refer to the section “Obtaining Service and Support” later in this
document.
This document contains the following sections:
•Safety Recommendations, page 2
•Rack-Mounting the Router, page 3
•Wall-Mounting the Router, page 12
•Obtaining Service and Support, page 16
•Cisco Connection Online, page 17
78-3635-01
2Cisco 3600 Series Rack-Mount and Wall-Mount Configuration Note
Safety Recommendations
Warning To ensure your safety and the safety of others, be sure the power is OFF and the power
cord is unplugged before working on the router. (To see translated versions of this warning, refer to
the Regulatory Compliance and Safety Information document that accompanied your router.)
Caution To avoid damaging electrostatic discharge (ESD)-sensitive components, ensure that you
have discharged all static electricity from your body before opening the chassis. Before performing
procedures described in this document, review the next section, “Safety Recommendations.”
Safety Recommendations
Follow these guidelines to ensure general safety:
•Keep the chassis area clear and dust-free during and after installation.
•Put the removed chassis cover in a safe place.
•Keep tools away from walk areas where you or others could fall over them.
•Do not wear loose clothing that could get caught in the chassis. Fasten your tie or scarf and roll
up your sleeves.
•Wear safety glasses when working under any conditions that might be hazardous to your eyes.
•Do not perform any action that creates a potential hazard to people or makes the equipment
unsafe.
Safety with Electricity
Warning Beforeworkingonequipmentthatis connected to powerlines,removejewelry(including
rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and
can cause serious burns or weld the metal object to the terminals. (To see translated versions of this
warning, refer to the Regulatory Compliance and Safety Information document that accompanied
your router.)
Follow these guidelines when working on equipment powered by electricity:
•Locate the emergency power-OFF switch in the room in which you are working. Then, if an
electrical accident occurs, you can quickly shut the power OFF.
•Before working on the router, turn OFF the power and unplug the power cord.
•Disconnect all power before doing the following:
—Installing or removing a router chassis
—Working near power supplies
—Performing a software upgrade
•Do not work alone if potentially hazardous conditions exist.
•Never assume that power is disconnected from a circuit. Always check.
Cisco 3600 Series Rack-Mount and Wall-Mount Configuration Note 3
Rack-Mounting the Router
•Look carefully for possible hazards in your work area, such as moist floors, ungrounded power
extension cables, and missing safety grounds.
•If an electrical accident occurs, proceed as follows:
—Use caution; do not become a victim yourself.
—Turn OFF power to the router.
—If possible, send another person to get medical aid. Otherwise, determine the condition of the
victim and then call for help.
—Determine if the person needs rescue breathing or external cardiac compressions; then take
appropriate action.
Preventing Electrostatic Discharge Damage
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. It occurs when
electronic printed circuit cards are improperly handled and can result in complete or intermittent
failures. Always follow ESD prevention procedures when removing and replacing cards. Ensure that
the router chassis is electrically connected to earth ground. Wear an ESD-preventive wrist strap,
ensuring that it makes good skin contact. Connect the clip to an unpainted surface of the chassis
frame to safely channel unwanted ESD voltages to ground. To properly guard against ESD damage
and shocks, the wrist strap and cord must operate effectively. If no wrist strap is available, ground
yourself by touching the metal part of the chassis.
Caution For safety, periodically check the resistance value of the antistatic strap, which should be
between 1 and 10 megohms (Mohm).
Rack-Mounting the Router
This section explains how to mount a Cisco 3620 or Cisco 3640 router in a 19-inch, 23-inch, or
24-inch equipment rack or telco rack. If you have questions or need help with the rack-mounting
procedure, refer to the section “Obtaining Service and Support” later in this document.
If you are planning to rack-mount your router, do so before making network and power connections.
If you need to install network modules or WAN interface cards, you can do so either before or after
mounting the router, whenever you have better access to the rear of the router.
Required Tools and Equipment
You need the following tools and equipment to mount a Cisco 3600 series router in a rack:
•Number 2 Phillips screwdriver
•ESD-preventive wrist strap
•Screws for attaching the router to the rack (not supplied)
Each router is shipped with one set of brackets. Brackets for 19-inch racks are shipped unless you
specify 23-inch or 24-inch brackets at the time of your order. Figure 1 shows brackets for the
Cisco 3620 router, and Figure 2 shows brackets for the Cisco 3640 router.
4Cisco 3600 Series Rack-Mount and Wall-Mount Configuration Note
Rack-Mounting the Router
Figure 1 Cisco 3620 Rack-Mount Brackets
Figure 2 Cisco 3640 Rack-Mount Brackets
Rack-Mounting the Cisco 3620 Router
This section explains how to rack-mount the Cisco 3620 router.
Attaching Brackets to the Cisco 3620 Router
To install the router in a rack with the front panel forward, attach the brackets on each side of the
chassis as shown in Figure 3 or Figure 4.
Figure 3 Cisco 3620 19-Inch Bracket Attachment—Front Panel Forward
H7270
Bracket for use with
a 23 or 24-inch rack
Use with 23-inch rack
Bracket for use
with a 19-inch rack
or for mounting on
a wall
Use with 24-inch rack
H6028
Bracket for use with
a 23 or 24-inch rack
or for wall-mounting
Use with 23-inch rack
Bracket for use
with a 19-inch rack
Use with 24-inch rack
H7271
0
ACTIVE
READY
1
PCMCIA
1
0
Cisco 3600 Series Rack-Mount and Wall-Mount Configuration Note 5
Rack-Mounting the Router
Figure 4 Cisco 3620 23-Inch or 24-Inch Bracket Attachment—Front Panel Forward
To install the router in a rack with the rear panel forward, attach the brackets on each side of the
chassis as shown in Figure 5 or Figure 6.
Figure 5 Cisco 3620 19-Inch Bracket Attachment—Rear Panel Forward
Figure 6 Cisco 3620 23-Inch or 24-Inch Bracket Attachment—Rear Panel Forward
To install the router in a center-mount telco rack, attach the brackets on each side of the chassis as
shown in Figure 7 or Figure 8.
H7272
0
ACTIVE
READY
1
PCMCIA
1
0
Note: The second bracket attaches to the other side of the chassis.
AUI
EN
ACT
SERIAL
H7273
Note: The second bracket attaches to the other side of the chassis.
AUI
EN
ACT
SERIAL
H7274
6Cisco 3600 Series Rack-Mount and Wall-Mount Configuration Note
Rack-Mounting the Router
Figure 7 Cisco 3620 Telco 19-Inch Bracket Attachment—Rear Panel Forward
Figure 8 Cisco 3620 Telco 23-Inch or 24-Inch Bracket Attachment—Rear Panel Forward
Mounting the Cisco 3620 Router in a Rack
After you fasten the brackets to the chassis, you can mount it in a rack. Using your own screws,
attach the chassis to the rack as shown in Figure 9 or Figure 10.
Figure 9 Mounting the Cisco 3620 in a 19-Inch Rack—Rear Panel Forward
AUI
EN
ACT
SERIAL
H7275
Note: The second bracket attaches to the other side of the chassis.
The brackets can also be installed with the front panel forward.
AUI
EN
ACT
SERIAL
H7276
Note: The second bracket attaches to the other side of the chassis.
The brackets can also be installed with the front panel forward.
AUI
EN
ACT
SERIAL
H7277
Note: The second bracket attaches to the rack at the other side
of the chassis. The brackets can also be installed with the
front panel forward.
Cisco 3600 Series Rack-Mount and Wall-Mount Configuration Note 7
Rack-Mounting the Router
Figure 10 Mounting the Cisco 3620 in a 23-Inch or 24-Inch Rack—Rear Panel Forward
Attaching Cable Guides to the Cisco 3620 Router
Attach the cable guides to the rack-mounting brackets on each side of the chassis as shown in
Figure 11 or Figure 12.
Figure 11 Attaching Cisco 3620 Cable Guides to 19-Inch Rack-Mounting Brackets
Figure 12 Attaching Cisco 3620 Cable Guides to 23-Inch or 24-Inch Rack-Mounting Brackets
AUI
EN
ACT
SERIAL
H7278
Note: The second bracket attaches to the rack at the other side
of the chassis. The brackets can also be installed with the
front panel forward.
24-inch rack23-inch rack
2E
2W W1
1
ETHERNET 1 ETH 1
ETHERNET 0
EN
AUI
WO
ACT
LNK
ACT
LNK
ACT
SERIAL
BRI
NT1
B1
B2
NT1
2E
2WW1
ETHERNET 0
AUI
EN
ACT
LNK
ACT
LNK
DO NOTINSTALL WAN INTERFACE
CARDSWITH POWER APPLIED
ACT
SERIAL
SEE MANUAL BEFORE INSTALLATION
H7569
0
ETHERNET 1
Cable guides
2E
2W W1
1
ETHERNET 1 ETH 1
ETHERNET 0
EN
AUI
WO
ACT
LNK
ACT
LNK
ACT
SERIAL
BRI
NT1
B1
B2
NT1
2E
2WW1
ETHERNET 0
AUI
EN
ACT
LNK
ACT
LNK
DO NOT INSTALL WAN INTERFACE
CARDS WITH POWER APPLIED
ACT
SERIAL
SEE MANUAL BEFORE INSTALLATION
H7570
0
ETHERNET 1
Cable guides
8Cisco 3600 Series Rack-Mount and Wall-Mount Configuration Note
Rack-Mounting the Router
Rack-Mounting the Cisco 3640 Router
This section explains how to rack-mount the Cisco 3640 router.
Attaching Brackets to the Cisco 3640 Router
To install the router in a rack with the front panel forward, attach the brackets on each side of the
chassis as shown in Figure 13 or Figure 14.
Figure 13 Cisco 3640 19-Inch Bracket Attachment—Front Panel Forward
Figure 14 Cisco 3640 23-Inch or 24-Inch Bracket Attachment—Front Panel Forward
To install the router in a rack with the rear panel forward, attach the brackets on each side of the
chassis as shown in Figure 15 or Figure 16.
H6251
0
ACTIVE
READY
12 3
PCMCIA
1
0
Note: The second bracket attaches to the other side of the chassis.
H6252
0
ACTIVE
READY
123
PCMCIA
1
0
Note: The second bracket attaches to the other side of the chassis.
Cisco 3600 Series Rack-Mount and Wall-Mount Configuration Note 9
Rack-Mounting the Router
Figure 15 Cisco 3640 19-Inch Bracket Attachment—Rear Panel Forward
Figure 16 Cisco 3640 23-Inch or 24-Inch Bracket Attachment—Rear Panel Forward
To install the router in a center-mount telco rack, attach the brackets on each side of the chassis as
shown in Figure 17 or Figure 18.
Figure 17 Cisco 3640 Telco 19-Inch Bracket Attachment—Rear Panel Forward
H6031
Note: The second bracket attaches to the other side of the chassis.
INPUT 100-240VAC 50/60HZ 3.0-1.5 AMPS
AUI
EN
WO
BRI
S/T
2
0
INPUT 100-240VAC 50/60HZ 3.0-1.5 AMPS
AUI
EN
WO
BRI
S/T
2
0
H6032
Note: The second bracket attaches to the other side of the chassis.
INPUT 100-240VAC 50/60HZ 3.0-1.5 AMPS
AUI
EN
WO
BRI
S/T
2
0
H6033
Note: The second bracket attaches to the other side of the chassis.
The brackets can also be installed with the front panel forward.
10 Cisco 3600 Series Rack-Mount and Wall-Mount Configuration Note
Rack-Mounting the Router
Figure 18 Cisco 3640 Telco 24-Inch Bracket Attachment—Rear Panel Forward
Mounting the Cisco 3640 Router in a Rack
After you fasten the brackets to the chassis, you can mount it in a rack. Using your own screws,
attach the chassis to the rack as shown in Figure 19 or Figure 20.
Figure 19 Mounting the Cisco 3640 in a 19-Inch Rack—Rear Panel Forward
INPUT 100-240VAC 50/60HZ 3.0-1.5 AMPS
AUI
EN
WO
BRI
S/T
2
0
H6034
Note: The second bracket attaches to the other side of the chassis.
The brackets can also be installed with the front panel forward.
INPUT 100-240VAC 50/60HZ 3.0-1.5 AMPS
AUI
EN
WO
BRI
S/T
2
0
H6035
Note: The second bracket attaches to the rack at the other side
of the chassis. The brackets can also be installed with the
front panel forward.
Other manuals for 3600 Series
9
This manual suits for next models
10
Table of contents
Other Cisco Rack & Stand manuals
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
