Cisco SG 300-10P User manual

Cisco Ethernet Switch Quick Setup Guide

For MuxLab AV over IP Devices

Cisco Ethernet Switch Quick Setup Guide

Contents

Introduction ...............................................................................................................31.

MuxLab Ethernet Switch Setup Requirements..........................................................32.

Ethernet Switch Setup...............................................................................................43.

3.1. Enabling IGMP...............................................................................................4

3.2. Enabling Jumbo Frames................................................................................8

Preparing for System Installation ..............................................................................94.

Cisco Ethernet Switch Quick Setup Guide

Introduction1.

This document covers the basic setup requirements for a Cisco Ethernet Switch. The

setup examples and screen shots shown are for the Cisco model SG300-10P, but these

instructions are similar and applicable to other Cisco Ethernet Switch models.

MuxLab Ethernet Switch Setup Requirements2.

All MuxLab AV over IP Transmitters and Receivers require IGMP support to be enabled

on the Ethernet Switch, and a select number of MuxLab units also require Jumbo

Frames to be enabled.

Also note that all models below work on a 1G Ethernet Switch, except for the 500760,

which requires a 10G Ethernet Switch.

The below table specifies the IGMP and Jumbo Frames requirement per MuxLab AV

over IP Transmitter / Receiver model.

AV over IP

Model

Ethernet Switch

BW Required

IGMP

Required

Jumbo Frame

Required

500752

500753

500754

500755

500755-AMP

500756

500757

500758

500759

500760

10G

500762

500770

500771

Cisco Ethernet Switch Quick Setup Guide

Ethernet Switch Setup3.

3.1. Enabling IGMP

Follow the steps below to enable the IGMP feature on the Ethernet Switch. For further

details on navigating through the Ethernet Switch web server menus, please refer to the

Ethernet Switch manual.

Step 1: Access the Ethernet Switch web server

-Locate the Ethernet Switch default IP address

-Make sure your computer is on the same subnet as the Ethernet Switch

(your network administration can assist you with this, if required)

-Enter the Ethernet Switch IP address into a browser

Step 2: IGMP Snooping Configuration

-Navigate to the menu:

[Multicast →Properties]

-Set the configuration as shown below, and then click [Apply]

Cisco Ethernet Switch Quick Setup Guide

-Navigate to the menu:

[Multicast →IGMP Snooping]

-(a) Enable the “IGMP Snooping Status” as shown below, and then click [Apply]

Cisco Ethernet Switch Quick Setup Guide

-(b) Select the radio button as shown below, and click [Edit]

Cisco Ethernet Switch Quick Setup Guide

-(c) Set the configuration as shown below, and then click [Apply]

Step 3: Save the above configuration changes

-Navigate to the menu:

[Administration →File Management →Copy/Save Configuration]

-Click on [Apply] as shown below

Cisco Ethernet Switch Quick Setup Guide

3.2. Enabling Jumbo Frames

Follow the steps below to enable the Jumbo Frames feature on the Ethernet Switch. For

further details on navigating through the Ethernet Switch web server menus, please

refer to the Ethernet Switch manual.

Step 1: Enable Jumbo Frames

-Navigate to the menu:

[Port Management > Port Settings]

-Check the “Jumbo Frame” checkbox as shown below, then click [Save]

Step # 2: Save the above configuration changes

-Navigate to the menu:

[Administration > File Management > Copy/Save Configuration]

-Click on [Apply]

Cisco Ethernet Switch Quick Setup Guide

Preparing for System Installation4.

The Ethernet Switch is now properly configured to support MuxLab AV over IP devices

with respect to IGMP and Jumbo Frames.

Note that MuxLab AV over IP Transmitters and Receivers are set by default with DHCP

enabled, and the MuxLab 500811 ProDigital Network Controller has DHCP disabled by

default and is set to a Static IP address of 192.168.168.50. It is recommended that you

operate your system with the Transmitters and Receivers with DHCP enable and the

500811 Network Controller with DHCP disabled.

If however you intend to disable the DHCP on the Transmitters and Receivers, then

please take note that the default Static IP address for the Transmitters is

192.168.168.55, and for the Receivers is 192.168.168.56.

Note that in order for the entire system to operate correctly, the Ethernet Switch,

MuxLab Transmitters and Receivers, and the MuxLab ProDigital Network Controller

must all be on the same subnet. Devices with DHCP enabled will adjust automatically to

the correct subnet, while devices with DHCP disabled, may need to be set by the user to

the correct subnet, if not already set correctly. Your network administrator can assist with

this configuration if you are not familiar with how to accomplish this task.

If you are having issues which require further assistance, please contact the respective

device manufacturer for the device in question. For MuxLab device related questions,

please contact MuxLab Customer Technical Support at 877-689-5228 (toll-free in North

America) or (+1) 514-905-0588 (International).

Cisco Ethernet Switch Quick Setup Guide

8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5

Tel: (514) 905-0588

Fax: (514) 905-0589

Toll Free (North America): (877) 689-5228

E-mail: videoease@muxlab.com URL:

www.muxlab.com

Table of contents

Other Cisco Network Router manuals

Cisco

Cisco AIRONET CB21AG User manual

Cisco

Cisco ASR 903 User manual

Cisco

Cisco RV340 Series Quick start guide

Cisco

Cisco ASR1002 - ASR 1002 Router User manual

Cisco

Cisco ASR-920-20SZ-M Operating and safety instructions

Cisco

Cisco ASR 9912 User manual

Cisco

Cisco RVS4000 - Gigabit Security Router Instruction Manual

Cisco

Cisco 2500 Series Operator's manual

Cisco

Cisco WRT400N Setup guide

Cisco

Cisco CRM3 Instruction Manual

Cisco

Cisco 2612 Manual

Cisco

Cisco 1700 series User manual

Cisco

Cisco IE 4000 Manual

Cisco

Cisco 3600 Series Quick start guide

Cisco

Cisco Linksys SRW208 User manual

Cisco

Cisco 8600 User manual

Cisco

Cisco 850 Series User manual

Cisco

Cisco 7200 Series User manual

Cisco

Cisco NCS 5000 Series User manual

Cisco

Cisco ASR 9000 Series User manual

Cisco

Cisco 809 Manual

Cisco

Cisco RV130 User manual

Cisco

Cisco Profile Series Instruction Manual

Cisco

Cisco Nexus 7000 Series Instruction Manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

EnGenius

EnGenius ESR-9710 quick start guide

LevelOne

LevelOne FBR-1416 user manual

Dynacord

Dynacord Promatrix 6000 Operation manual

Lorex

Lorex F5D8230-4 Guide