Cisco LINKSYS RFC 2364 Original operating instructions

QUICK INSTALLATION

ADSL Gateway

There are two ways to set up the

Gateway, run the Setup CD-ROM

or use this Quick Installation.

Linksys strongly recommends

that you run the Setup CD-ROM.

Run the Setup CD-ROM

Insert the Setup

CD-ROM into the

CD-ROM drive, and

follow the on-screen

instructions.

Use this Quick

Installation

Follow the instructions

in this Quick Installation.

This method should only

be used if you cannot

run the Setup CD-ROM.

Connection

Make sure that all the devices that you are working with are powered down,

including your computer(s) and the Gateway.

Connect one end of the provided

phone cable to the wall jack with

ADSL service.

Connect the other end of the

phone cable to the DSL/Line port

on the back of the Gateway.

NOTE: To avoid interference, you may need to place a microfilter

or splitter between the phone cable and wall jack. Contact your ISP

to determine if one is required. (UK residents need to connect the

microfilter to the wall phone jack with ADSL service and then connect

one end of the provided phone cable to the RJ-11 port on it.)

If you use ISDN, then you do not need a microfilter.

Connect one end of the provided

Ethernet cable to your computer’s

Ethernet adapter. Connect the

other end of the Ethernet cable to

one of the Ethernet ports on the

back of the Gateway.

Repeat this process for every

computer that you want to connect

to the Gateway via Ethernet.

If you are connecting more than

four computers to the Gateway, you

will also need to connect a switch

to the Gateway.

NOTE: If your computer’s Ethernet adapter is not set up, refer to the

Ethernet adapter’s user guide for more information.

1�

Connect the Phone CableConnect the Phone Cable

Connect the Ethernet CableConnect the Ethernet Cable

Connect the power adapter to

the Gateway’s power port and the

electrical outlet.

Power on the Gateway.

Power on the computer that you

want to use to configure the

Gateway.

NOTE: If you have more than one phone and you experience static on

the line after installing the Gateway, then you will need an additional

microfilter for each phone or fax that you use.

Proceed to Step 2: Configuration.

Configuration

In Step 2, configure the Gateway to access the Internet through your ADSL

Internet Service Provider (ISP). Use the setup information provided by your ISP.

NOTE: You only need to configure the Gateway once.

Open your web browser. Enter

http://192.168.1.1 in the web

browser’s Address field. Press the

Enter key.

On the login screen, enter admin

in lowercase letters in both the User

Name and Password fields (admin

is the default user name and

password). Click OK.

2�

Connect the Power AdapterConnect the Power Adapter

Access the Web-Based UtilityAccess the Web-Based Utility

The Basic Setup screen appears. Refer to the settings provided by your ISP.

Select the Encapsulation method your ISP has specified.

For the Multiplexing setting, select LLC or VC.

For the Virtual Circuit, enter the VPI and VCI settings.

Proceed to the appropriate instructions for your Encapsulation method.

NOTE FOR UK RESIDENTS ONLY: Select or enter the following

settings unless otherwise instructed by your ISP.

Encapsulation: RFC 2364 PPPoA

Multiplexing: VC

VPI: 0

VCI: 38

RFC 2364 PPPoA or RFC 2516 PPPoE

Enter your Username and Password.

Select Keep Alive if you always

want to be connected to your ISP, or

select Connect on Demand if you

are charged for the time that you

are connected to your ISP.

Click Save Settings.

3. RFC 2364 PPPoA

RFC 2516 PPPoE

RFC 2364 PPPoA

RFC 2516 PPPoE

RFC 1483 Routed or IPoA

Enter the IP Address, Subnet Mask,

and Default Gateway IP address.

In the Primary and/or Secondary

DNS fields, enter at least one DNS IP

address.

Click Save Settings.

RFC 1483 Bridged - Dynamic IP Address

For the IP Setting, select Obtain an

IP Address Automatically.

Click Save Settings.

RFC 1483 Routed

IPoA

RFC 1483 Routed

IPoA

RFC 1483 Bridged - Dynamic IP AddressRFC 1483 Bridged - Dynamic IP Address

Website

http://www.linksys.com/international

For additional information or troubleshooting help, refer to the User Guide on the CD-ROM.

Additional support is also available via e-mail or by phone.

Linksys is a registered trademark or trademark of Cisco Systems,Inc. and/or its

trademarks of their respective holders.

Product Registration

http://www.linksys.com/registration

70222NC-JL

RFC 1483 Bridged - Static IP Address

For the IP Setting, select Use the

Following IP Address.

Enter the IP Address, Subnet Mask,

and Default Gateway IP address.

In the Primary and/or Secondary

DNS fields, enter at least one DNS IP

address.

Click Save Settings.

Bridge Mode Only

This mode is used only if you are using

the Gateway as a bridge, which makes

the Gateway act like a stand-alone

modem. Click Save Settings.

To test the setup, enter

www.linksys.com/registration in

the web browser’s Address field, and

press Enter.

NOTE FOR WIRELESS GATEWAYS: Refer to the User Guide on

the CD-ROM for instructions on wireless configuration. Linksys

recommends that you change the wireless settings from the defaults

and enable the appropriate security method.

Congratulations! The installation of the Gateway is complete.

RFC 1483 Bridged - Static IP AddressRFC 1483 Bridged - Static IP Address

Bridge Mode OnlyBridge Mode Only

Popular Gateway manuals by other brands

LST

LST M500RFE-AS Specification sheet

Kinnex

Kinnex Media Gateway quick start guide

2N Telekomunikace

2N Telekomunikace 2N StarGate user manual

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Original instructions

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE user guide

Telsey

Telsey CPVA 500 - SIP Technical manual

RTA

RTA 460A-NNA4 Product user guide

Shaw

Shaw Gateway HDPVR user manual

ABB

ABB VSN900 Commissioning manual

Commander

Commander Pulse owner's manual

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E manual

NETGEAR

NETGEAR C6300BD installation guide

Amit

Amit CDW531AM user guide

HMS

HMS Netbiter EasyConnect EC150 user manual

Huawei

Huawei EchoLife HG620 user guide

AT&T

AT&T U-verse 3801 Replacement self-installation guide

Logic IO

Logic IO RTCU MX2 turbo Technical manual

Suttle

Suttle MediaMAX MXM-521 installation instructions