CIGGO Tattoo Plus 75 User manual

TattooPlus 75TattooPlus 75

CIGGO Tattoo Plus includes:

1* CIGGO Tattoo Plus Box Mod

1* User Manual

Specification

Size: 88mm*26.5mm*42.8mm

Output Mode: TEMP-Ni/ TEMP-Ti/ TEMP-SS/POWER/BYPASS

Output Wattage: 1W～75W

Support resistance: Above 0.05Ω

Temperature range: 100℃~315℃(200~600℉)

Each +/- increase or decrease 5℃/10℉

Hidden Full Length LED Display, Durable Stainless Steel, Single 18650 battery (sold separately),

Max Discharge Current over 20 A,

510 Thread.

Pieces & Parts

A) Fire Button

B) Adjust Up Button

C) Adjust Down button

D) USB Port (underneath)

E) Hidden Screen

F) Front Side

E) F)

How to Use

1. Turn On/Turn Off：

Slide off the battery cover, and put 1pc 18650 cell into the battery holder(recommends: high-rate and better

branded 18650 cells, Max discharge current over 20A)

Press the firing button 5 times within 2S to turn on the devise on/off, Power on screen display “CIGGO”, and

then enter Resistance Screen.

2. Details Operation Steps

Enter Setting Mode:

Press both adjustment buttons simultaneously. Come out interface image B, then press”+” and “-” together in

3 seconds to select a working mode. Once desired mode is reached, press the fire button to confirm.

Long Press "+"and "-" together over 5 seconds. The screen will show "UPDATE". Then the whole mod

freezes. You have to actually remove the batteries and then put them back in to get it to work.

Display Screens:

A) Turning on Screen

B) Power Mode

C) Nichrome TC Mode

D) Titanium TC Mode

E) Stainless Steel TC Mode

F) BYPASS Mode

B3.8V B3.6V

3. Vaping

Hold the firing button and inhale from the atomizer mouthpiece, release the firing button and exhale

The “ ” battery symbol will change to “ ”lightning symbol

4. Adjust power:

Press adjustment buttons. Longer press=Faster adjustment

(After you have made your selection/adjustments, the display will show your power output for 1s and then

your resistance for 3s)

How to Switch Fahrenheit and Celsius

Press “+” “-” to get temperature up and down. Celsius increases/decreases 5℃each time. Once

temperature reaches

315℃, press “+” shortly to switch to Fahrenheit. (Fahrenheit increases/ decreases 10F each time). Repeat this

operation, Celsius and Fahrenheit will switch.

5. How to adjust wattage under Ni/Ti/SS MODE:

Press fire button and “+” simultaneously or press fire button and”-” simultaneously, then you can adjust wattage.

6. Invalid to press “+” ”-” under BYPASS MODE. It’s mechanical

mode, you can vape directly.

7. Short Circuit Protection：

If the device didn’t screw with atomizer or the atomizer resistance is exceed supporting range, screen display

“Ω”symbol flashing 3 times.

8. Standby Mode:

If no more operation within 30S,the device will shut off the screen. Press fire button, display

screen will light up again.

9. Over Discharge Remind Protection：

If vaping voltage is lower than 3.3V, the battery symbol will flash 5 times to remind you the device needs

charging, and it turns off automatically.

10. Over Intake Protection：

Single puff over 10S, device will stop output.

11. Over heat Protection:

If device inner temperature is over 70℃under VW mode, the screen will display “HOT”, you need to wait till the

temperature goes down to below 68℃.

12. Shut OFF Screen Function：

Pressing “+” and “-” simultaneously can shut off and turn on the screen.

13. Vaping Level Check Function:

Pressing “fire button” and “+” simultaneously can check your vaping level.

14. Charging & Upgrade Your Device

5V 1A Micro USB charging port for charging and upgrade your program.

How to edit your led screen:

1. 1) Make sure your box mod don't have battery cell inside.

(if you already have battery cell inside , please take it out), keep the box mod empty or at least the battery

slider is open.

2) Press both "+" and "-" at the same time , and put the battery cells into the box mod , then cover back the the

battery slider.

3) after operation 2) , screen shows"C0" (image F), it means you are setting the first word. When the setting

letter chosen , the letter will flash (image G), press "+" or "-" to select the letter or number you want to

choose.

image F (C0) image G

TAUO

Other CIGGO Electronic Cigarette manuals

CIGGO

CIGGO Banshee Plus User manual

Popular Electronic Cigarette manuals by other brands

STEAMAX

STEAMAX TFV8 X-BABY user manual

iQOS

iQOS 3 MULTI user guide

Vaporesso

Vaporesso LUXE XR MAX user manual

ZAZO

ZAZO PRO Mini 2 user manual

Aquafog

Aquafog Turbo XE User's manual and operating instructions

Electronic Cigarettes Australia Pty Ltd

Electronic Cigarettes Australia Pty Ltd AUSSIE BLUE ENDURANCE user manual

UWELL

UWELL Whirl T1 user manual

VooPoo

VooPoo VMATE instruction manual

Yogs-Pfeifen

Yogs-Pfeifen E-PIPE nex KLASSIK manual

TSI Instruments

TSI Instruments 3075 instruction manual

Vaporesso

Vaporesso GTX ONE user manual

VooPoo

VooPoo DRAG 2 user manual

Innova

Innova 3.0 instructions

Aquafog

Aquafog XE CRSM user manual

hi-Fun

hi-Fun hi-Cigarette user manual

Neptronic

Neptronic SKH Series user guide

Vaporesso

Vaporesso LUXE Q2 SE user manual

iQOS

iQOS 3 DUO user manual