CHIEF PAC-170 User manual

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 

CHIEF MANUFACTURING INC. 8807-000049 (Rev. A)

1-800-582-6480 952-894-6280 FAX 952-894-6918 ©2005 Chief Manufacturing

8401 EAGLE CREEK PARKWAY, STE. 700 www.chiefmfg.com

SAVAGE, MINNESOTA 55378 USA 09/05

INSTALLATION INSTRUCTIONS

Small Flat Panel Bracket – Floor Stand

(PAC-170)

The PAC-170 Floor Stand assembly is compatible with

small flat panels and other products and accessories

offered by Chief.

PARTS

Figure 1. Parts

PARTS LIST

Unpack the shipping carton and check for the contents

listed in Table 1 and shown in Figure 1.

Table 1. Parts List

REF DESCRIPTION QTY

10 FRONT BRACKET, floor stand

(with attached mounting plate)

1

20 SCREW, button head cap, 5/16-18 x ½” 4

30 BACK BRACKET, floor stand 1

40 ALLEN KEY, 3/16” 1

10

20

30

40

Installation Instructions PAC-170

2

TOOLS REQUIRED FOR INSTALLATION

• 3/16” Allen Key (provided)

NOTE: Other tools may be required depending on your

method of installation.

INSTALLATION

To install the PAC-170 bracket assembly, do the

following:

Attach PAC-170 to Floor Stand

NOTE: Make sure that mounting plate faces toward the

front of the floor stand before attaching the

PAC-170 to the floor stand.

1. Attach front bracket (10) and back bracket (30) to

the floor stand post (see Figure 2) using four

5/16-18 x ½” button head cap screws (20).

2. Adjust the PAC-170 to the desired height on the

floor stand.

3. Tighten the screws.

Mount the Display

1. Make sure power is not supplied (turned off) to the

display and the locking device is in the unlocked

(down) position (see Figure 4) before attempting to

mount the display.

2. Following the instructions for mounting the PSB

interface bracket of your specific plasma display

panel, install the mounting bracket on your plasma

display panel.

3. With an assistant, slide the display down over the

mounting plate on the PAC-170. Make sure buttons

of PSB interface bracket fully engage all teardrop

slots on the mounting plate.

4. Secure the mounting bracket to the PAC-170 by

completely engaging the locking device

(see Figure 4).

WARNING: Make sure the locking device securing the

display is completely engaged at all times

except when removing or installing the

display.

NOTE: A padlock may be used on the locking device for

increased security.

5. Connect and secure power/audio/video cables (not

shown).

Figure 2. Attach PAC-170 to Floor Stand

Figure 3. Mount the Display

Figure 4. Locking Device

10

Floor Stand Pos

t

30

20

PAC-170

PSB Bracket Interface

Dis

p

la

y