CHIEF MSP-KTPHD Series User manual

M S P - K T P H D - X X Q U I C K S T A R T G U I D E

This Quick Start Guide is meant to provide only an overview of the various installation steps.

ALWAYS read the Installation Instructions for each individual product within this kit before

beginning the Installation.

WARNING: Exceeding the weight capacity

can result in serious personal injury or

damage to equipment! It is the installer’s

responsibility to make sure the combined

weight of all components attached to the

MSP-KTPHD-XX up to (and including) the

display does not exceed 35 lbs (15.87 kg) per

interface..

MSP-KTPHD-FS MSP-KTPHD-GM MSP-KTPHD-DC

Pole Attachment for MSP-KTPHD-FS - Assemble pole

to base using one 3/8-16 x 1" flat head cap screw.

Pole attachment for MSP-KTPHD-GM -Locate desired point on

surface where mount is to be installed. Drill a 1/2" diameter hole

through surface. Align grommet mount base plates with hole in

surface. Slide one 3/8-16 x 6" hex head cap screw upward

through lower grommet plate, through hole in surface and through

upper grommet plate. Place pole, provided with array accessory,

onto upper grommet plate aligning threaded hole in pole bottom

with threaded end of 3/8-16 x 6" hex head cap screw. Thread 3/8-

16 x 6" hex head cap screw into pole bottom and tighten with 9/16"

wrench to secure pole and grommet plates to surface.

pole upper grommet plate

lower grommet plate

3/8-16 x 6" screw

1a 1b

Pole attachment for MSP-

KTPHD-DC NOTE: In order

to reduce the chance of

scratching to the mounting

surface, bumpers may be

installed. However,

installation of bumpers is

optional.

Remove adhesive from

underside of bumpers.

Attach bumpers to underside

of desk clamp.

Use 7/32" hex key to install

3/8-16 x 1" flat head cap

screw through the opening

on top of desk clamp and

into bottom of mounting pole

Place desk clamp over desired mounting location on desk.

Turn clamp screw until the clamp is secured to the desk as tightly

as possible.

pole

base

3/8 x 16 x 1" screw

pole

3/8 x 16 x 1"

desk clamp

clamp screw

bumpers

MSP-KTPHD Quick Start Guide

Adjustments

To adjust display Roll, Pitch and Yaw:

a. Disconnect all wires and cables.

b. Remove display.

c. Using a hex head wrench, turn the tension

adjustment screw clockwise to increase tension or

counter-clockwise to decrease tension.

d. Re-install display, wires and cables.

a. Route cables and wires to display.

b. Route cables and wires through cable

management covers.

c. Snap cable management covers onto pole.

Place mount against pole, with clamp on opposite side of pole.

Using 5/32" hex key, loosely assemble with three 1/4-20 x 1-

1/4" button head cap screws.

mount

pole

pole clamp

1/4-20 x 1-1/4" screws x 3

8800-003381 Rev01

2023 Legrand | AV

www.legrandav.com

02/2023

Chief, a brand of Legrand

6436 City West Parkway, Eden Prairie, MN

55344

• P: 800.582.6480 / 952.225.6000 • F:877.894.6918 /

952.894.6918

Legrand | AV and its affiliated corporations and subsidiaries (collectively “Legrand

| AV”), intend to make this manual accurate and complete. However, Legrand |

AV makes no claim that the information contained herein covers all details, con-

ditions or variations, nor does it provide for every possible contingency in connec-

tion with the installation or use of this product. The information contained in this

document is subject to change without notice or obligation of any kind. Legrand |

AV makes no representation of warranty, expressed or implied, regarding the in-

formation contained herein. Legrand | AV assumes no responsibility for accuracy,

completeness or sufficiency of the information contained in this document.

a. Start two M4 x 8mm Phillips pan head screws

(included in hardware kit) into upper mounting

holes in display back.

NOTE: Leave at least 1/8" of each screw protruding out back

of display.

b. Align two screws in display back with upper

mounting holes in Centris cup and lower display

until screws are seated in lower area of teardrop

mounting holes. (See Figure 4)

c. Install two more of the same screws through lower

mounting holes in Centris cup and into display

back. (See Figure 4)

d. Tighten all hardware.

4 x 8mm screws x 2

This manual suits for next models

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 