CHIEF MSP-BBSP User manual

Installation Instructions MSP-BBSP

IMPORTANT WARNINGS AND PRECAUTIONS!

WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: ACAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corre-

sponding instructions.

•WARNING:Improper installation can result in serious personal injury! Make sure that the structural members can

support a redundant weight factor five times the total weight of the equipment: if not, reinforce the struc-

ture before installing the mount.

•WARNING:Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.

•WARNING:The installer is responsible for verifying that the wall to which the mount is anchored will safely support

the combined load of all attached components or other equipment.

•WARNING:The weight of the display placed on the mountmust not exceed 40 lbs. (18.1 kg), the maximum load capac-

ity of the mount.

•WARNING:Watch for pinch points. Do not put your fingers between movable parts.

•WARNING:Make sure the mount and brackets are correctly oriented.

•CAUTION: Check the unit for shipping damage before you begin the installation.

CONTENTS

SPECIFICATIONS ....................................................1

TOOLS REQUIRED FOR INSTALLATION ..............1

DRAWINGS ..............................................................2

INSPECT THE UNIT BEFORE INSTALLING ...........3

iC-SP-TP1-01 INSTALLATION .................................3

ADJUSTMENTS .......................................................5

SPECIFICATIONS

This mount accommodates all VESA® 75mm/100mm compli-

ant displays. Table 1 provides mount specifications.

TOOLS REQUIRED FOR

INSTALLATION

• Electric drill and bit set

• Phillips Screwdriver

• Level

NOTE: Other tools may be required depending on the

mounting surface and method of installation.

Table 1: Specifications

Depth from Wall 3.34” (84.74mm)deep in the closed

position

Dimensions (WxHxD) 2-3/8”x 5-11/16” x 1-13/16”

(61 x 145 x 46 mm)

Tilt +/-15 degrees

Pivot 180 degrees

Weight Capacity 40 lbs. (18.2 kg)

Installation Instructions MSP-BBSP

DRAWINGS

#10 Wood Screws

Wall Plate

M4 X 8mm, 12mm, 16mm, 20mm or 30mm Phillips pan head screws

1/8” Spacers

(optional)

Adjustment Knob

End Cap

Set Screw

Tension Adjustment Bolt

Installation Instructions MSP-BBSP

INSPECT THE UNIT BEFORE INSTALLING

WARNING: Watch for pinch points. Do not put your fingers

between movable parts.

1. Carefully inspect the mount for shipping damage. If any dam-

age is apparent, call your carrier claims agent and do not con-

tinue with the installation until the carrier has reviewed the

damage.

NOTE: Read all instructions before starting installation.

2. Lay out components to ensure you have all the required parts

before proceeding (see drawing on page 2).

INSTALLATION

WARNING: It is the responsibility of the installer to verify that

the structure to which the mount is anchored will

safety support five times the combined load of all

attached components and equipment.

1. Determine the exact mounting location prior to installation,

considering the unit’s swing radius.

2. Using the wall plate as a template, drill two 3/32” pilot holes to

a minimum depth of 1 1/2” into wall stud.

3. Using two Phillips head #10 wood screws (supplied), secure

the wall plate (see Figure 1).

4. Install screw cover (see Figure 2).

5. Check mount to insure it is level and adjust to level if neces-

sary.

6. Determine if you are installing a VESA compliant flush mount

display, VESA compliant recessed mount display or a non-

VESA compliant display and follow the appropriate instruc-

tions.

VESA Compliant Flush Mounting

A. Install the mount on the wall plate, set to desired height at

one of the fixed height settings and secure by tightening

the set screw (see Figure 3).

B. Install the end caps on the wall plate (see Figure 4).

CAUTION: If monitor uses a screw size other than M4, DO NOT

use the M4 screws provided. Using the wrong screws

could result in damage to your display.

C. Start two M4 X 12mm Phillips pan head screws in the top

mounting holes of your display.

D. Matching the hole pattern on your display with the hole

pattern on the mount (see Figure 5), hang the mount from

the two screws started in Step A.

Figure 1. Secure Wall Plate

Figure 2. Install Screw Cover

Figure 3. Install iC-SP-TP1

and Tighten Set Screw

Fixed Height Settings

Set Screw

Figure 4. Install End Caps

Installation Instructions MSP-BBSP

E. Install two remaining Phillips pan head screws through the

mount and into the mounting holes of your display.

F. Secure your display to the mount by tightening the four

Phillips pan head screws.

WARNING: Make sure your cables do not run through a pinch

point.

G. Connect and secure power/audio/video cables, making

sure to leave sufficient slack to allow for movement of the

display.

VESA Compliant Recessed Mounting

A. Place four 1/2” X 3/8” Nylon spacers or four 1/2” X 3/4”

Nylon spacers, as necessary, over the mounting holes of

your display (see Figure 6).

B. Place the mount over the Nylon spacers, matching the hole

pattern on your display (75mm or 100mm) with the hole

pattern on the mount.

C. Using four M4 X 20mm Phillips pan head screws for 1/2”

X 3/8” Nylon spacer installation or four M4 X .7 X 30mm

Phillips pan head screws for the 1/2” X 3/4” Nylon spacer

installation, secure the mount to your display.

H. Install the mount on the wall plate, set to desired height at

one of the fixed height settings and secure by tightening

the set screw (see Figure 3).

J. Install the end caps on the wall plate (see Figure 4).

WARNING: Make sure your cables do not run through a pinch

point.

K. Connect and secure power/audio/video cables, making

sure to leave sufficient slack to allow for movement of the

display.

Non-VESA Compliant Mounts

A. Contact Chief Manufacturing for custom interface brack-

ets.

Figure 5. Flush Mounting

Figure 6. Recessed Mounting

Installation Instructions MSP-BBSP

INSTALLATION (200mm x 100MM)

Attach Interface Adapter to Display

1. Select six M4 X 16mm Phillips flat head screws and six

1/8” nylon retaining spacers.

2. Place display face down on a clean dry surface.

3. Align six 1/8” nylon spacers over mounting holes in dis-

play back (see Figure 7).

4. Align interface bracket mounting holes with 1/8” nylon

spacers.

5. Install six M4 X 16mm Phillips flat head screws through

six mounting holes in interface bracket, spacers and into

display (see figure 7).

6. Tighten six M4 X 16mm Phillips flat head screws.

Attach Centris Bracket to Display

1. Start two M4 x 8mm Phillips pan head screws into the top

two mounting holes of interface bracket (see figure 8).

2. Hang mount from two screws.

3. Install the remaining two M4 x 8mm Phillips pan head

screws into the bottom two mounting holes of interface

bracket.

4. Secure the display to the mount (Centris bracket) by tight-

ening four M4 x 8mm Phillips pan head screws.

Interface Bracket

M4 X 16mm

Phillips Flat Head Screws (6)

1/8” Nylon Spacers (6) Display

Figure 7. Install Interface Bracket

Interface Bracket

M4 X 8mm

Phillips Pan Head Screws (4)

Display

Centris Bracket

Figure 8. Attach Centris Bracket to Display

Installation Instructions MSP-BBSP

ADJUSTMENTS

CAUTION: Overtightening adjustment will cause excessive wear.

Rotational Tilt, Pitch, and Roll Adjustment

1. If necessary, use a Phillips screwdriver to tighten or loosen

the Phillips pan head screw (see DRAWINGS).

2. Check for desired tension.

3. Repeat Steps 1 and 2 until desired tension is obtained.

Lateral Tension Adjustment

1. Using a 3/16” hex wrench (provided), slightly tighten or

loosen lateral tension adjustment bolt (see DRAWINGS).

2. Check for desired tension.

3. Repeat Steps 1 and 2 until desired tension is obtained.

Patents and patents pending. 8/05

8832-000089 (Rev. A)

Chief Manufacturing Inc.

8401 Eagle Creek Parkway, Suite 700 CSAV Europe B.V.

Savage, MN 55378, USA Zekeringstraat 17, 1014 BM

PHONE: 800.582.6480 Amsterdam, Netherlands

PHONE: 952.277.3901 PHONE: 31 (0)20 5708923

FAX: 952.894.6918 FAX: 31 020 5708989

FAX: 877.894.6918 eu[email protected]

www.chiefmfg.com

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 