CHIEF KSA-1020 User manual

INSTALLATION INSTRUCTIONS

Instrucciones de instalación

Installationsanleitung

Instruções de Instalação

Istruzioni di installazione

Installatie-instructies

Instructions d´installation

Wall and Desk CPU Mount

Spanish Product Description

German Product Description

Portuguese Product Description

Italian Product Description

Dutch Product Description

French Product Description

KSA-1020

KSA-1020 Installation Instructions

DISCLAIMER

Milestone AV Technologies, and its affiliated corporations and

subsidiaries, (collectively, Milestone) intend to make this

manual accurate and complete. However, Milestone makes no

claim that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Milestone

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Milestone assumes

no responsibility for accuracy, completeness or sufficiency of

the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.

IMPORTANT WARNINGS AND

CAUTIONS!

WARNING:

A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION:

A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

WARNING:

Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all components are

properly assembled and installed using the instructions

provided.

WARNING:

Failure to provide adequate structural strength

for this component can result in serious personal injury or

damage to equipment! It is the installer’s responsibility to

make sure the structure to which this component is attached

can support five times the combined weight of all equipment.

Reinforce the structure as required before installing the

component.

WARNING:

Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components attached to this accessory does not exceed

40 lbs (18.1 kg).

DIMENSIONS

CPU RANGE

[0 - 191]

0" - 7.50"

WIDTH OF

CPU RANGE

[248 - 457]

.26

MOUNTING

HOLES

1.46

MOUNTING SURFACE

TO CPU SURFACE

UNDER DESK MOUNTED CONFIGURATION

360

SWIVEL

CAPABILITY

Installation Instructions KSA-1020

LEGEND

Tighten Fastener

Apretar elemento de fijación

Befestigungsteil festziehen

Apertar fixador

Serrare il fissaggio

Bevestiging vastdraaien

Serrez les fixations

Loosen Fastener

Aflojar elemento de fijación

Befestigungsteil lösen

Desapertar fixador

Allentare il fissaggio

Bevestiging losdraaien

Desserrez les fixations

Phillips Screwdriver

Destornillador Phillips

Kreuzschlitzschraubendreher

Chave de fendas Phillips

Cacciavite a stella

Kruiskopschroevendraaier

Tournevis à pointe cruciforme

Open-Ended Wrench

Llave de boca

Gabelschlüssel

Chave de bocas

Chiave a punte aperte

Steeksleutel

Clé à fourche

By Hand

A mano

Von Hand

Com a mão

A mano

Met de hand

À la main

Hex-Head Wrench

Llave de cabeza hexagonal

Sechskantschlüssel

Chave de cabeça sextavada

Chiave esagonale

Zeskantsleutel

Clé à tête hexagonale

Pencil Mark

Marcar con lápiz

Stiftmarkierung

Marcar com lápis

Segno a matita

Potloodmerkteken

Marquage au crayon

Drill Hole

Perforar

Bohrloch

Fazer furo

Praticare un foro

Gat boren

Percez un trou

Adjust

Ajustar

Einstellen

Ajustar

Regolare

Afstellen

Ajuster

Remove

Quitar

Entfernen

Remover

Rimuovere

Verwijderen

Retirez

Optional

Opcional

Optional

Opcional

Opzionale

Optie

En option

Security Wrench

Llave de seguridad

Sicherheitsschlüssel

Chave de segurança

Chiave di sicurezza

Veiligheidssleutel

Clé de sécurité

Installation Instructions KSA-1020

TOOLS REQUIRED FOR INSTALLATION

PARTS

7/64" #2

1/2"

17/64"

1/2"

F(1)

A(1)

B(2)

C(4)

D(1) E(2)

G(2)

3/8 X 1 1/4" #12 X 2 1/2"

1/4-20 X 1 3/4"

Installation Instructions KSA-1020

ASSEMBLY AND INSTALLATION

Installation of Protective Rubber Edging

1. Place four strips of protective rubber edging (C) over the

sharpedgeslocated on thetopandbottom of the mount(A).

(See Figure 1)

Figure 1

CPU Installation

1. Release bracket from mount by moving the flag to the open

position. (See Figure 2)

2. Remove bracket from mounting buttons on back of mount.

(See Figure 2)

Figure 2

3. If hanging mount underneath desk, remove mounting

buttons to reinstall them in the holes in which they will be

used.

• If mounting vertically, move mounting buttons in

the four holes on top of the mount. (See Figure 3)

• If mounting horizontally, move mounting buttons

in the top four holes on the back. (See Figure 3)

Figure 3

4. Loosen adjustment knob at the back of the mounting unit

and adjust height of mount to a height greater than the

height of the CPU to be installed. Loosen strap at the front

of the mount if necessary. (See Figure 4)

Figure 4

5. Loosen adjustment knobs on top and bottom of the mount

and slide flanges in order to allow for the CPU to be inserted

for mounting. (See Figure 5)

NOTE:

Top and bottom knobs can be removed and inserted

into the front square holes in order to allow for large

(A)

Vertical button location Horizontal button location

KSA-1020 Installation Instructions

CPU’s to be installed. (See Figure 5)

NOTE:

Flanges may be reversed in order to allow for narrow

CPU’s to be installed in a secure manner. If this is

done, be sure to also to remove and reinstall strap so

that the buckle is facing out for easy adjustment.

Figure 5

6. Set CPU within mount (A). (See Figure 6)

7. UseadjustmentknobstocompressmountaroundCPUuntil

CPU is tightly secured within mount (A). (See Figure 6)

Figure 6

8. Tighten front strap to desired tension.

WALL MOUNT INSTALLATION

WARNING:

FAILURE TO PROVIDE ADEQUATE

STRUCTURAL STRENGTH FOR THIS MOUNT CAN

RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE

TO EQUIPMENT! It is the installer’s responsibility to make

sure the structure to which this mount is attached can support

five times the combined weight of the mount and all

equipment attached to it. Reinforce the structure as required

before installing the mount.

NOTE:

Mount may be installed using wood studs, steel studs

or it may be installed directly into drywall. For steel stud

and drywall installation, proceed ahead to Site

Requirements for Using Steel Studs section. For desk

mounting, proceed ahead to Desk Mounting

Installation section.

Mount Installation Using Wood Studs

1. Determine location for mount keeping in mind CPUsize and

safety requirements.

2. Using the removed mounting bracket as a template, mark

and then drill two 7/64" diameter pilot holes through top and

bottom holes of wall bracket into wall structure. (See Figure

Figure 7

3. Install two #12 x 2 1/2" round Phillips wood screws (G)

through bracket and drywall into wood stud. (See Figure 7)

4. Ensure bracket is vertical, then tighten screws (G).

NOTE:

Proceed ahead to Mounting CPU to Wall section to

complete installation.

(G) x 2

mounting bracket

Installation Instructions KSA-1020

Site Requirements for Using Steel Studs

WARNING:

IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY

OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for installation of display mounts onto a

steel stud structure. If the structure or its components do not meet these requirements contact the mount manufacturer for specific

instructions before attempting installation. It should also be noted that no other equipment should be mounted to the same stud.

Figure 8

inside wall

Specification for the Design of Cold-Formed Steel Structural Members.

Steel Stud (2 x 4 / 25ga minimum)

Drywall

Mount Installation Location

FRONT

(Must be centered on stud)

There must be a minimum of

1 7/8" (48mm) clearance

16" or 24" (on center) Studs

If back side of wall is unfinished, drywall must be installed

to a minimum of one stud left and right of the stud(s)

being used to install the mount. Drywall must be

secured to studs with screws 12" on center

Stud type and structural strength must conform to the North American

**1/2"

Thickness

(Both Sides of Stud)

[362 S 125 18, C-Shaped, S-Stud Section]

minimum Drywall

**See Hazard statement

on page 2!

KSA-1020 Installation Instructions

Wall Mounting Using Steel Studs or Drywall

After determining the site meets the installation requirements:

1. Identify desired mounting location on wall.

2. Using a stud finder or similar method locate stud.

3. Align mounting holes in mount with stud making sure

mounting holes are centered on stud. (See Figure 9)

WARNING:

IMPROPER INSTALLATION CAN LEAD TO

EQUIPMENT FALLING CAUSING SERIOUS PERSONAL

INJURY OR DAMAGE TO EQUIPMENT!

4. Mark location of two mounting holes on wall using the wall

plate as a template. Mark holes where the top and bottom

holes of the bracket will be connected. (See Figure 9)

5. Drill two 1/2" holes. (See Figure 9)

Figure 9

6. Hold metal channel on anchor (B) flat alongside plastic

straps and slide channel through hole. (See Figure 10)

Figure 10

7. Holding plastic straps on anchor (B), pull anchor away from

wall until channel rests flush behind wall making sure

anchor channel is positioned vertically on stud. (See Figure

11)

8. Slide plastic cap on anchor (B) towards wall until flange of

cap is flush with wall. (See Figure 11)

Figure 11

9. Snap off plastic straps on anchor at wall by pushing side to

side, snapping off straps level with flange of plastic cap.

(See Figure 12)

10. Repeat steps 6 through 9 for remaining mounting hole.

Figure 12

11. Place mounting bracket over anchors and align mounting

holes in display mount with holes in anchors. (See Figure

13)

12. Insert 1/4-20 x 1-3/4" Phillips pan head screw (E) into

mounting hole on mounting bracket and into anchor (B) and

tighten until flush against mounting bracket. DO NOT

overtighten! (See Figure 13)

13. Repeat steps 11 through 13 for remaining mounting hole.

1/2"x2

1/2"(

Mounting holes centered on stud

(B) x 2

Drywall

Plastic Straps

Plastic Cap

Steel Stud

Drywall

Anchor Metal Channel

(Side View)

(B) x 2

Plastic Straps

Steel Stud

Drywall

Anchor Metal Channel

Plastic Cap

(SIDE VIEW)

Installation Instructions KSA-1020

Figure 13

Mounting CPU to Wall

CAUTION:

Overtightening screws may cause wall bracket

to compress into soft wall surface resulting in difficult mount

installation.

1. Ensure bracket flag is in the open position. (See Figure 2)

2. Insert mounting buttons into the four large mounting holes

on the bracket. (See Figure )

Figure 14

3. Move flag to closed position in order to fully secure mount

to bracket. (See Figure 15)

Figure 15

Desk Mount Installation

WARNING:

Failure to provide adequate structural strength

for this component can result in serious personal injury or

damage to equipment! It is the installer’s responsibility to

make sure the desk to which this component is attached can

support five times the combined weight of all equipment.

Reinforce the structure as required before installing the

component.

NOTE:

The following instructions are for mounting with full

360° swivel capability for easy cord access. If this

capability is not desired, connect mounting bracket

usingtwoscrews as demonstratedinthe wall mounting

instructions.

1. Determine location for mount keeping in mind CPUsize and

safety requirements.

2. Using bracket and bearing (D) as a template, mark and drill

one 17/64" diameter pilot hole through underside of desk at

desired mounting location. Ensure entire mount will clear

the outer edge of desk. (See Figure 16)

Steel Stud

Drywall

Anchor Metal Channel

Mounting Bracket

(SIDE VIEW)

(E) x 2

(Flag in closed position)

KSA-1020 Installation Instructions

Figure 16

3. Install 3/8 x 1 1/4" hex head lag screw (F) through bearing

(D) and bracket into hole drilled in Step 2. (See Figure 16)

4. Ensure bracket flag is in the open position.

5. Insert four mounting buttons into four mounting holes on the

bracket. (See Figure 17)

Figure 17

6. Slide buttons into locked position within holes.

7. Move flag to closed position in order to fully secure mount

to bracket. (See Figure 15)

(D)

(F)

desk

mounting bracket

Other manuals for KSA-1020

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 