CHIEF FSD-4100 User manual
FSD-4100
LCD Flat Screen
Swing-Down Mount
Perfect for home applications under kitchen cabinets or other
rooms with a soffit. The LCD Flat Screen Swing-Down mount is
a sturdy, versatile solution for LCD flat screen display or touch
screen control system mounting with 15” or smaller monitors.
The all steel mount provides smooth side-to-side pivot, 70º or
220º screen rotationand extends and retracts 2 3/4” to allow for
larger screen capacity. Hidden cable management permits aes-
thetic installation while preventing wires from being pinched.
BEFORE YOU BEGIN
•Caution: To prevent damage to the mount, which could affect the equipment that will be attached to it and
void the factory warranty, thoroughly study all instructions and illustrations before you begin the installa-
tion. Pay particular attention to the “Important Warnings and Precautions” on Page 1.
•The mount isdesigned to be installed on cabinetry or supporting framework. The cabinet to which the FSD-4100 is
anchored must be capable of supporting 75 pounds (34 Kg).
•If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480.
CHIEF MANUFACTURING INC.
1-800-582-6480 952-894-6280 FAX 952-894-6918
8401 EAGLE CREEK PARKWAY
SAVAGE, MINNESOTA 55378 USA
8832-000010 Rev C
©2007Chief Manufacturing
www.chiefmfg.com
04-07
INSTALLATION INSTRUCTIONS
Installation Instructions FSD-4100
1
IMPORTANT WARNINGS AND PRECAUTIONS!
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: ACAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corre-
sponding instructions.
•WARNING:Improper installation can result in serious personal injury! Make sure that the mounting surface can sup-
port a redundant weight factor five times the total weight of the equipment. If not, reinforce the structure
before installing the FSD-4100.
•WARNING:Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.
•WARNING:The installer is responsible for verifying that the surface to which the FSD-4100 is anchored will safely
support the combined load of all attached components or other equipment.
•WARNING:The weight of the display placed on the FSD-4100 must not exceed 15 lbs. (6.8 kg), the maximum load
capacity of the FSD-4100.
•WARNING:Watch for pinch points. Do not put your fingers between movable parts.
•WARNING:Make sure the mount and brackets are correctly oriented.
•CAUTION: Check the unit for shipping damage before you begin the installation.
•CAUTION: Overtightening adjustment bolt will cause excessive wear and may distort adjustment components.
NOTE: Hardware for attaching this unit to the mounting surface is not supplied.
TOOLS REQUIRED FOR INSTALLATION
•Phillips screw driver
•Electric drill motor
•1/4” Drill bit
NOTE: Other tools may be required depending on the
method of installing the mount.
CONTENTS
DIMENSIONAL DRAWING ........................................ 2
INSPECT THE UNIT BEFORE INSTALLING ............ 3
PARTS ....................................................................... 4
FDS-4100 INSTALLATION ........................................ 5
MOUNT THE DISPLAY ............................................. 5
ADJUSTMENTS ......................................................... 6
CABLE MANAGEMENT ............................................. 7
2
Installation Instructions FSD-4100
DIMENSIONAL DRAWING
Installation Instructions FSD-4100
3
INSPECT THE UNIT BEFORE INSTALLING
WARNING: Watch for pinch points. Do not put your fingers
between movable parts.
1. Carefully inspect the FSD-4100 for shipping damage. If any
damage is apparent, call your carrier claims agent and do not
continue with the installation until the carrier has reviewed the
damage.
NOTE: Read all instructions before starting installation.
2. Lay out components to ensure you have all the required parts
before proceeding (see “DIMENSIONAL DRAWING” on
page 2 and “PARTS” on page 4).
4
Installation Instructions FSD-4100
PARTS
Item Description Qty. Item Description Qty.
10 Mount 1 40 Screw, M4 X .7 X 20mm 4
10A Base Cover 1 50 Screw, M4 X .7 X 10mm 4
10B Cable Management Cover 1 60 Spacer, Nylon, .500 OD X .19 X .50 4
20 Nuts, T 3 70 Tie Wraps 4
30 Screws, 10-24 X 5/8” 3 80 Allen Wrench, 5/32” 1
30 40
50 60 70
80
10 10A
10B
20
Installation Instructions FSD-4100
5
FSD-4100 INSTALLATION
WARNING: It is the responsibility of the installer to verify that
the surface to which the FSD-4100 is anchored will
safety support the combined load of all attached
components and equipment.
Install the FSD-4100 as follows:
NOTE: Numbers in ( ) refer to parts in PARTS on page 4.
1. Remove two screws securing base cover (10A) and remove
cover (see Figure 1).
2. Determine the exact mounting location prior to installation,
considering the unit’s total arm radius.
3. Using the mounting plate as a template, mark mounting hole
locations (see Figure 2).
4. Drill three 1/4” holes at the locations marked in step 3.
WARNING: Improper installation can result in serious dam-
age to the display or personal injury! Make sure
that the structural members can support a redun-
dant weight factor five times the total weight of the
equipment. If not, reinforce the structure before
installing the FSD-4100.
5. With theFSD-4100correctly oriented andlevel, secureit tothe
surface using fasteners (20 and 30).
6. Check mount to insure it is level and adjust to level if neces-
sary.
MOUNT THE DISPLAY
1. Make sure no power is supplied to the display before attempt-
ing to mount the display.
WARNING: Watch for pinch points. Do not put your fingers or
cables between movable parts.
2. Align the appropriate slots in the bracket with the four mount-
ing holes of your LCD display (see Figure 3).
WARNING: Make sure the mounting screws used to secure
your display panel to the mounting bracket are the
proper length and diameter. If you are unsure
about screw length and/or diameter, consult the
display manufacturer before proceeding.
3. Using the proper length and diameter screws (40 or 50), and
spacers (60) as necessary, secure your display to the mount.
NOTE: If your display is not equippedwith 75 \mm or 100mm
mounting pattern, contact Chief Manufacturing to check for an
adapter plate for your display model.
Base Screws
Cover
Secure
Display
Figure 1. Remove Cover
Figure 3. Secure Display
Figure 2. Mark Mounting Location
Mark
Hole
Locations
6
Installation Instructions FSD-4100
ADJUSTMENTS
Screen Height Adjustment
1. Using a screw driver, slightly loosen the screws (40
or 50) securing the display panel to the mounting bracket
(see Figure 4).
2. Adjust the display panel to the desired height.
3. Using a screw driver, tighten the screws securing the dis-
play panel to the mounting bracket.
Arm Tension Adjustment
CAUTION: Overtightening adjustment bolt will cause exces-
sive wear and may distort adjustment components.
1. Using a 5/32” Allen wrench (80), slightly tighten or loosen
the tension adjustment bolt at the base of the arm (see
Figure 5).
2. With display mounted, cycle the FSD to check fordesired
tension.
3. Repeat Step 1 and Step 2 until desired tension is
obtained.
Screws
Securing
Monitor
Figure 4. Loosen/Tighten Screws
Securing Monitor
Tension Adjustment Bolt
Figure 5. Adjust Arm Tension
Installation Instructions FSD-4100
7
CABLE MANAGEMENT
1. Remove screw and cable management cover (10B) (see
Figure 6).
2. Route the power/audio/video cables down the arm (see
Figure 7).
3. Route the power/audio/video cables through the slot in the bot-
tom of the arm (see Figure 8).
4. Secure the power/audio/video cables using tie wraps.
5. Proceed to “Right and Left 35 Degree Rotation” on page 8 or
“Right and Left 110 Degree Rotation” on page 9, depending
upon your application.
Cable
Management
Cover
Figure 6. Cable Management Cover
Figure 7. Route Cables Down Arm
Tie Wraps
Figure 8. Route & Tie Wrap Cables (Arm)
8
Installation Instructions FSD-4100
Right and Left 35 Degree Rotation
1. Turn the base 35 degrees in one direction to its stop (see
Figure 9).
2. Neatly and carefully, route the power/audio/video cables
through the slot in the side of the base.
3. Secure the power/audio/video cables using a tie wrap (70).
4. Trim excess from tie wrap.
5. Install cable cover (10B) on arm and secure using screw (see
Figure 10).
6. Install base cover (10A) on base and secure using two screws
(see Figure 10).
Base Cover
Cable Cover
Figure 10. Install Base and Cable Covers
35 Degrees
Tie Wrap
Stop
Slot
Figure 9. Route & Tie Wrap Cables (Base)
Installation Instructions FSD-4100
9
Right and Left 110 Degree Rotation
1. Using an Allen wrench (provided), remove the 35 degree stop
(see Figure 11).
2. Turn the base 110 degrees in one direction to its stop (see
Figure 12).
3. Neatly and carefully, wrap power/audio/video cables twice
inside base with no slop or slack in cables (see Figure 13).
4. Route power/audio/video cables out access hole in base.
5. Secure cables to base using a tie wrap (70).
6. Trim excess from tie wrap.
7. Install cable cover (10B) on arm and secure using screw (see
Figure 10).
8. Install base cover (10A) on base and secure using two screws
(see Figure 10).
35 Degree Stop
Figure 11. Remove 35 Degree Stop
110 Degrees
Figure 12. Rotate 110 Degrees
Figure 13. Wrap Cables In Base
Table of contents
Other CHIEF Rack & Stand manuals
CHIEF
CHIEF 25MWR Service manual
CHIEF
CHIEF SSB-202 User manual
CHIEF
CHIEF PNRIW Series User manual
CHIEF
CHIEF PAC230 User manual
CHIEF
CHIEF K1W Series User manual
CHIEF
CHIEF CMA440 User manual
CHIEF
CHIEF Kontour KRA226 User manual
CHIEF
CHIEF K0W100 User manual
CHIEF
CHIEF MSP-DCCPPNR User manual
CHIEF
CHIEF CPA116 User manual
CHIEF
CHIEF PNRIW Series User manual
CHIEF
CHIEF LCM1UP User manual
CHIEF
CHIEF K1 User manual
CHIEF
CHIEF FSRV4100 User manual
CHIEF
CHIEF HVP-6 User manual
CHIEF
CHIEF FSA-1005 User manual
CHIEF
CHIEF Vibration Mount CMA-347 User manual
CHIEF
CHIEF JSB2090 User manual
CHIEF
CHIEF FWD-111 User manual
CHIEF
CHIEF XTM Series User manual
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
