CHICAGO 34552 User manual

MINI-TIRE

CHANGER

Model

34552

INSTRUCTIONS AND

PRECAUTIONS

Please note: Tire not included.

Visit our website at: http://www.harborfreight.com

SAVE THESE

INSTRUCTIONS.

READ ALL

PRECAUTIONS AND

INSTRUCTIONS.

reserved. No portion of this document or any artwork

contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight

Tools. Diagrams within this document may not be drawn

proportionally. Due to continuing improvements, actual

product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

For technical questions or replacement parts,

please call 1-800-444-3353.

SPECIFICATIONS

Tire Rim Capacity 4” to 12” Rim

Height 16”

Includes

(2) Bead Breaker Handles

21” Long Mount/Demount Tool

Aluminum Centering Cone

(2) Nylon Spacers

UNPACKING

When unpacking, make sure that the item is

intact and undamaged. If any parts are missing or

broken, please call Harbor Freight Tools at

1-800-444-3353 as soon as possible.

IMPORTANT SAFETY INFORMATION

Do not exceed max. tire capacity. Do not use on1.

tires with rims exceeding 12” diameter.

Wear ANSI-approved safety goggles and heavy-2.

duty work gloves during assembly, mounting and

use.

Use as intended only. This Mini-Tire Changer3.

has been designed for ATVs, golf carts, and

small car maintenance. Use only with vehicle

tires for which it was designed.

Do not modify Mini-Tire Changer to perform tasks4.

for which it was not designed.

Use only with accessories included with the Mini-5.

Tire Changer.

Mount only to a secure, level surface able to6.

support weight of Mini-Tire Changer and tire

assembly.

Verify that mounting surface has no hidden utility7.

lines before drilling or driving screws.

Lubricate Breaker Handles (4, 5) when removing8.

tire from rim; failure to do so can lead to property

damage.

Keep work area clean and well lit.9.

Keep bystanders out of the area during use.10.

Do not use when tired or when under the11.

inuence of drugs, medication or alcohol.

This product is not a toy. Do not allow children to12.

play with or near this item.

Inspect before every use; do not use if parts are13.

loose or damaged.

Maintain product labels and nameplates. These14.

carry important safety information. If unreadable

or missing, contact Harbor Freight Tools for a

replacement.

Page 2 For technical questions, please call 1-800-444-3353. SKU 34552

ASSEMBLY/MOUNTING

INSTRUCTIONS

Read ENTIRE IMPORTANT SAFETY

INFORMATION section at beginning of

this document including all text under

subheadings therein before set up or use.

The Mini Tire-Changer can be mounted1.

temporarily in a vise (not included) or

permanently to a secure workbench or surface.

For permanent mounting, use pencil to mark2.

installation holes. Use mounting hardware

(not included) to mount the Base onto a secure

workbench or stand, making sure that there are

no hidden cables or wiring below installation

surface.

Verify that all hardware (uses 7/16” or 1/2” bolts,3.

at and lock washers and hex nuts) are secure

and that base is mounted evenly and is level.

Insert Holder (16) into Base and lock together4.

using the Base Pin (13). See Figure 1.

For temporary mounting to a vise, position the5.

Base between vise jaws with the Base Pin

accessible from the sides of the vise. Tighten

vise jaws, Use vice jaw guards to prevent

damage to Holder surfaces. See Figure 2.

REMOVING TIRE OPERATION

Remove balancing weights, if any, from rim1.

edges.

Remove tire valve core to deplete the tire.2.

Place tire rim over Threaded Shaft (18). See3.

Figure 3.

Install cone end of the Alignment Disc (1) over4.

the Threaded Shaft (18).

Place both Spacers (2) over the shaft.5.

Thread the Locking Nut (3) over the Threaded6.

Shaft (18) and tighten.

Attach the end of the Forcing Handle (5) to the7.

tab of the Locking Nut (3) using one of the Pins

(6).

Insert Breaker Handle (4) through the slot in8.

Forcing Handle and attach the rubberized Grip

(12) to the Breaker Handle, making sure that

the nger grip end of the handle is towards the

Locking Nut.

To break tire beads, Breaker Handle foot should9.

rest horizontally over the tire at edge of rim. (Use

combination of adjustment holes in the Forcing

Handle and Breaker Handle and if required,

remove one of the Spacers). See Figure 4.

Figure 2

Hub Holder (16)

Vise

Figure 1

Holder (16)

Base (15)

Base Pin (13)

Figure 3

Locking Nut (3)

Spacer (2)

Alignment Disc (1)

Tire Assembly

Threaded Shaft (18)

Hub Holder (16)

Base (15)

Figure 4

Breaker

Handle (4)

Forcing Handle (5)

Pin (6)

Grip (12)

Page 3For technical questions, please call 1-800-444-3353.SKU 34552

Pull down on both handles until the bead slide off10.

the rim.

Remove mounting components and ip the tire 11.

off, forcing the tire off the rim.

Remove Pin and remove the Forcing Handle12.

assembly from the Locking Nut.

WARNING!13. Sharp edges can be left on the rim.

Be sure to wear heavy-duty work gloves and to

use caution when handling.

Lubricate each bead with to facilitate sliding of14.

the bead over the rim (Windex® window cleaner

is a good lubricant substitute.)

Push down on tire until there is enough room to15.

place the ball end of the Mounting/Demounting

Tool (11) under the bead on the opposite end of

the tire. See Figure 5.

Push handle of Mounting/Demounting Tool down,16.

raising the bead above the rim. See Figure 5.

With ball end still under the bead, pull handle of17.

Mounting/Demounting Tool around in a clockwise

direction. Hold tire to prevent it from turning.

See Figure 5.

Raise tire so that lower bead is just under the18.

upper lip of the rim. See Figure 6.

Position the ball end of Mounting/Remounting19.

Tool under lower bead of tire.

Push down on handle to push lower bead above20.

the rim.

Pull handle of Mounting/Remounting Tool21.

clockwise to remove bottom bead from the rim.

See Figure 6.

WARNING!22. Failure to use Bead lubricant when

removing the tire from the rim may result in

damage to the bead.

INSTALLING TIRE OPERATION

To mount a new or repaired tire, lubricate the1.

inside and outside both tire beads.

Push the lower bead onto the rim as far as it will2.

go without forcing it. See Figure 7.

Note:3. With proper use of bead lubricant, the

rst bead should slide complete onto the rim.

In cases where it does not, the Mounting/

Demounting Tool can be used to install the rst

bead.

Place the cut-out center of the Mounting/4.

Demounting Tool over the Locking Nut. See

Figure 8.

Figure 5

Mounting/Demounting Tool (11)

Figure 6

Mounting/Demounting

Tool (11)

Clockwise rotation

Figure 7

Base (15)

Figure 8

Mounting/Demounting

Tool (11)

Page 4 For technical questions, please call 1-800-444-3353. SKU 34552

Pull the hook at the end of the Mounting/5.

Demounting Tool snug against the edge of the

tire rim.

Push the tire down at a spot opposite the hook of6.

the Mounting/Demounting Tool. See Figure 8.

Hold the tire to keep it from turning as you pull7.

the Mounting/Demounting Tool clockwise. This

will force the bead over the rim’s upper edge.

See Figure 9.

Once the lower bead is completely over the edge8.

of the rim, install the upper bead, by following

Steps 2-7, as described above.

Remove the Mounting/Demounting Tool when the9.

tire is on the rim.

MAINTENANCE

After each use, wipe any excess bead oil off of1.

Mini-Tire Changer.

Regularly inspect Mini-Tire Changer to ensure2.

that all connections are secure.

PARTS LIST & ASSEMBLY DIAGRAM

Part Description Qty.

1 Alignment Disc 1

2 3” Spacer 2

3 Locking Nut 1

4 Breaker Handle 1

5 Forcing Handle 1

6 Pin 2

11 Mounting/Demounting Tool 1

12 Grip 1

13 Base Pin 1

14 Base 1

15 Holder 1

16 Protector Ring 1

17 Threaded Shaft 1

Figure 9

Mounting/Demounting

Tool (11)

Record Serial Number Here:

Note: If product has no serial number, record month and

year of purchase instead.

Note: Some parts are listed and shown for illustration

purposes only, and are not available individually as

replacement parts.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST

AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY.

NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION

OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO

MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO

REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR

DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS

SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT

BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF

HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT

PARTS THERETO.

Page 5For technical questions, please call 1-800-444-3353.SKU 34552

LIMITED 90 DAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability

standards, and warrants to the original purchaser that this product is free from defects in materials and

workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due

directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal

activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable

for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising

from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY

IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our

inspection veries the defect, we will either repair or replace the product at our election or we may elect to refund

the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired

products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within

the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specic legal rights and you may also have other rights which vary from state to

state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

Table of contents

Other CHICAGO Automobile Accessories manuals

CHICAGO

CHICAGO 92474 User manual

CHICAGO

CHICAGO 67498 User manual

Popular Automobile Accessories manuals by other brands

James Baroud

James Baroud Odyssey user guide

Motorola

Motorola i50sx owner's manual

Yakima

Yakima 9MM STANDARD BIKE MOUNT instructions

Feniex

Feniex T3 instruction manual

Renault

Renault 77 11 423 180 Installation instruction

Kia

Kia E8300-4D000 manual

Brink

Brink 756843 installation instructions

Whispbar

Whispbar K085W Fitting instructions

v.link

v.link CI-VL2-PC-HSD manual

Viking

Viking Stack-Rack Assembly and use instructions

Aries

Aries 203015 installation manual

Choetech

Choetech AT0005 user manual

ZZ2

ZZ2 ZZAIR-PRO instruction manual

Holman

Holman 4A80L installation guide

Thule

Thule 2075 parts manual

Motorola

Motorola T325 quick start guide

TAUBENREUTHER

TAUBENREUTHER 16-3950 FITTING INSTRUCTION

DV8

DV8 FBJL-02 Product installation manual