Checkmate TR3 User manual
TR3 Tripod
User Manual
ANSI Z359.18-2017
TR3 Tripod
Issue 0
TR3 Tripod
User Manual
Page
INDEX
1.0 Introduction to TR3 &
Scope of Use
2.0 Assembly
3.0 Confined Space Recommendations
4.0 Storage, Issue & Inspection
5.0 Quality, legislation & Exclusions
6.0 Installation, Use, Opening/Clearance
Requirements & Fall Clearance
7.0 Warning! & Compatibility
8.0 Labeling
9.0 Record Card
3
4 - 6
7 - 8
9
10
11 - 12
13
14
15
WARNING!
Working at height is dangerous. This product is designed to reduce
the risk of working at height, by providing protection in the event of a
fall to reduce the risk of injury. The product must be used as intended,
and the user must be trained, competent, and aware of the correct
usage and limitations of the product. The user MUST be supplied
with the manufacturers user instructions and MUST read and fully
understand and follow the instructions within. The user must also
comply with OSHA and local safety regulations.
Failure to follow these guidelines could result in injury or death.
The Checkmate TR3 meets the requirement of ANSI Z359.18-2017, A10.32.12,
OSHA 1910 and OSHA 1926 Subpart M
Issue 0
TR3 Tripod
User Manual
Introduction to TR3 & Scope of Use
PAGE 3 Section 1.0
TR3 Tripod
The TR3 Tripod has been designed for your safety. The TR3 is supplied as a passive fall arrest device. The
device is designed to be used above structures and confined entry areas where other attachment is not
possible. The TR3 is totally portable and is therefore a temporary anchorage. In the event of a fall the
Tripod will provide a tested anchorage and a secondary anchorage for rescue if required. If in any doubt
please clarify application with Checkmate Technical Support.
Head Pulley x 2
Locking tabs x 3
WG-01
Mounting Bracket
Leg Pins x 3
FABX2R or
FABXLR
Swivel Feet x 3
Anti-splay
Webbing
Eyebolt Attachment x 2
Position A = Max extension with bracket fitted
Position B = Min extension with bracket fitted
Position C = Min extension - no bracket (connect to eyebolt only)
Position HTHED
A 94 87 56
B 71 63 39
C 71 63 39
All measurements in inches
HT = Height to top of TR3 crown
HE = Height to bearing point of eyebolt
D = Diameter to inside of feet
For opening and clearance requirements please
see p.g. 11
Principal Materials:
Aluminum, stainless steel, galvanized steel,
powder coated steel, polyester, nylon
PART NO. DESCRIPTION
32200 Height adjustable tripod (TR3) & carry bag
32208 Tripod carry bag only
32205 Tripod (TR3), tripod bag, 65ft work winch (WG-01), winch adaptor bracket (WG-02), 60ft galvanized SRLR (FABX2R) &
SRLR adaptor bracket (FABXR-DB)
32206 Tripod (TR3), bag, 65ft work winch (WG-01), winch adaptor bracket (WG-02), 100ft galvanized SRLR (FABXLR) & SRLR
adaptor bracket (FABXLR-DB)
32207 Tripod (TR3), bag, 65ft winch (WG-01) & winch adaptor bracket (WG-02)
Model Designation
Issue 0
TR3 Tripod
User Manual
Assembly
Page 4 Section 2.0
NOTE:
The Checkmate TR3 and FABX2R/FABXLR are designed for rescue use only. If the device is to be used as
a primary man riding winch Checkmate recommend the use of a secondary rescue device. The device is
designed to be used in free running mode and in the event of a fall the user can be rescued via the winching
facility. For advice or further information contact Checkmate.
Fig. 1
Unpack tripod and stand upright.
Fig. 2
Release leg pins and slip up to
desired height.
Fig. 3
Lock individual legs with pins.
Fig. 4
Open legs out and ensure sprung
loaded tabs lock out in position.
Fig. 5
Check anti splay webbing is
secure.
Fig. 6
Ensure feet are sitting flat on the
ground as shown when used on
hard ground, or fully folded back
for use on soft ground.
Spiked Feet
Flat Feet
Issue 0
TR3 Tripod
User Manual
Assembly
Page 5 Section 2.0
Fig. 7
Fix FABXR-DB or FABXLR-DB with
two supplied pins.
Fig. 8
Insert FABX2R or FABXLR into
the bracket as shown seating the
cable end in the bracket
Fig. 9
Secure with M12 bolt.
Fig. 10
Pull cable up to tripod head and
insert hook through central hole.
Fig. 11
Slide sprung loaded pulley to right,
insert cable in pulley groove, and
release pulley.
Fig. 12
The device is now ready for use.
Follow the instructions for safe
use of other equipment.
Folding:
Reverse the above procedure, ensuring that the sprung loaded leg locking pins are released by hand before
folding each leg. It is acceptable to leave the FABX2R fitting in the FABXR-DB Bracket when removing from
the TR3.
Issue 0
TR3 Tripod
User Manual
Assembly
Page 6 Section 2.0
Fig. 1
Slide the bracket (WG-02)
which is fixed to the winch
onto the tripod leg.
Fig. 2
Align the holes in the bracket
with the holes in the tripod leg
and insert a detent pin.
Fig. 3
Insert the second detent pin.
Fig. 4
Pull cable up to tripod head
and insert hook through
central hole.
Fig. 5
Slide sprung loaded pulley to
right, insert cable in pulley
groove, and release pulley.
Issue 0
TR3 Tripod
User Manual
Page 7 Section 3.0
Confined Space
Recommendation Option 1
Primary Fall Arrest Device with Secondary Backup
When entering a confined space when a fixed access system is installed the user should use:
1 x Tripod (TR3)
1 x SRLR (FABX2R or FABXLR)
1 x SRLR adaptor bracket (FABXR-DB or FABXLR-DB)
The FABX2R/FABXLR should be in free run mode and in the event of a fall the device will automatically lock
on and then the winch can be engaged.
PLEASE NOTE THAT THE FABX2R/FABXLR IS NOT INTENDED TO BE USED AS A CONTINUOUS
WINCH, ONLY AS A RETRIEVAL DEVICE IN EMERGENCY SITUATIONS.
FABX2R or
FABXLR
Issue 0
TR3 Tripod
User Manual
Page 8 Section 3.0
Primary Raise and Lower Device with Secondary Backup
Confined Space
Recommendation Option 2
FABX2R or
FABXLR
WG-01
When entering a confined space when there is no fixed access system and there is a need to lower the
user down under control, you should use:
1 x Tripod (TR3)
1 x SRLR (FABX2R or FABXLR)
1 x SRLR adaptor bracket (FABXR-DB or FABXLR-DB)
1 x Work winch (WG-01)
1 x winch adaptor bracket (WG-02)
The WG-01 is your primary lowering device and in the event of a fall the FABX2R/FABXLR will
automatically lock on and the winch can be engaged.
Issue 0
TR3 Tripod
User Manual
Storage, Issue & Inspection
Page 9 Section 4.0
Storage
Storage in a central protected location allows assurance of inspection on issue and return
This tripod should be stored in a clean dry place where it can be protected from damage by chemical attack and sharp
objects . It should be stored with its instructions and record card at all times.
After use return to the store, Never leave the device lying around site.
Cleaning
To clean the tripod a mild detergent can be used with warm or cold water and then dry with a clean soft cloth.
Issue
This and associated equipment must be visually inspected by a competent person when initially delivered to site, there
after the product must be inspected before and after use. A record card is printed on the reverse of this manual and
should be updated after each routine inspection. Follow the points laid down in the section headed “Inspection” without
deviation.
The supervisor must ensure that the equipment is being used correctly and that the user is aware of its safe use and
inspection. Additionally the supervisor must ensure that the site to which the device is to be used has been approved fit
for use and is in a good condition.
Inspection & Maintenace
Inspect the device for corrosion or damage.
Check the head and leg pins for signs of wear or damage and replace wear necessary.
Pay attention to condition of leg tubes for damage, bends and hole wear.
Check the sprung loaded locking tabs self-engage when the legs are opened.
Check the sprung loaded pulleys return to central position when slid to the side and released.
Check the condition of the pulley and eyebolt attachment. Pulleys should run free, but the eyebolt must be fixed.
Check rubber pads are fitted and not missing on feet.
Check the condition of the entire length and buckle of the anti-splay tape for damage.
Check the device opens and closes fully.
Tripods which fail inspection must be removed from the field of service immediately and marked out of service. If
irreparable the Tripod must be destroyed and discarded to prevent further use.
Ensure that device certification is current before use, the device must have been serviced within the last 12 months and
3 months if used in corrosive or off-shore environments.
If for any reason the inspection of this device shows signs for concern or doubt then the device must be
quarantined and removed from service immediately. Qualification should be sought from the supervisor and if
still concerned the device must be sent to the supplier, an approved service agent or the manufacturer for
service and re-calibration.
This device must only be serviced by the manufacturer or a trained and competent individuals
approved by the manufacturer.
Never attempt to service this device or tamper with its function in any way.
Issue 0
TR3 Tripod
User Manual
Quality, Legislation & Exclusions
Page 10 Section 5.0
5.1 Quality
All Checkmate products are
manufactured under ISO 9001 and
to the highest standards. The scope of
use within the certification held allows
Checkmate to design, manufacture and
test Personal Protection Equipment.
Horizontal tensile test machine,
abrasion testers and dynamic drop test
rig are just part of the full range of test
facilities used to ensure ultimate safety
of our product range.
All Checkmate systems must only be
installed by Checkmate personnel or an
approved installer. Strict training is given
and written exam are completed before
full certification can be given to installers.
5.2 Legislation and Standards
The TR3 Tripod has been designed
to meet the requirements of ANSI
Z359.18:2017, A10.32.12,
OSHA 1910 and OSHA 1926 Subpart M
For clarification on any certification
issues contact Checkmate.
5.3 Exclusions
Checkmate holds global product
liability cover for your safety.
Checkmate will NOT however be
responsible for:
Users who are out of the scope of any
written manuals of training given.
Any systems that have NOT been
inspected under the current legislation.
Operators who do not use load limiting
PPE.
Devices that have been damaged.
The Max weight has been exceeded.
Devices that have NO serial number
markings, and the manufacturers name.
Checkmate Lifting & Safety Ltd present.
Rescue and Risk Assessment
Suitable planning and risk assessment
should be carried out by the user and or
supervisor. A suitable rescue plan and
equipment shall be in place to minimise
post fall suspension time. Checkmate
can offer a complete range of rescue
equipment to suit your requirements.
Table of contents
Popular Camera Accessories manuals by other brands
Viltrox
Viltrox EF-NEX Mount instructions
Calumet
Calumet 7100 Series CK7114 operating instructions
Ropox
Ropox 4Single Series User manual and installation instructions
Cambo
Cambo Wide DS Digital Series Main operating instructions
Samsung
Samsung SHG-120 Specification sheet
Ryobi
Ryobi BPL-1820 Owner's operating manual
