Chauvin Arnoux C.A 6609 User manual

Notice de fonctionnement

User’s manual

Bedienungsanleitung

Manuale d’uso

Manual de instrucciones

FRANÇAIS

ENGLISH

DEUTSCH

ITALIANO

ESPAÑOL

§Testeur de sens moteur et rotation

de phases

§Motor and Phase rotation indicator

§Drehfeldrichtungsanzeiger

§Tester di senso motore e rotazione

delle fasi

§Comprobador de sentido de motor

y rotación de fases

C.A 6609

---------------------------

English

You have just purchased a CA 6609 motor and phase rotation

indicator and we thank you for your confidence.

For best results from your device:

•read this user manual attentively,

•observe the precautions for its use.

Meaning of the symbols used on the instrument

Warning, possible hazard. Please refer to the user's

manual.

Correct orientation of the motor when positioning the

instrument.

Battery

Instrument protected by double insulation.

The CE marking guarantees compliance with European

directives and with the regulations governing EMC.

Selective sorting of wastes for the recycling of electrical

and electronic equipment within the European Union.

In conformity with directive WEEE 2002/96/EC: this

equipment must not be treated as household waste.

Earth.

Office: Jl. Radin Inten II No. 62 Duren Sawit, Jakarta 13440 - Indonesia

Workshop: Jl. Pahlawan Revolusi No. 22B, Jakarta 13430 - Indonesia

Phone: 021-8690 6777 (Hunting) Fax: 021-8690 6777

Mobile: +62 816 1740 8925

English

This instrument can be used on category III electrical circuits not

exceeding 600V with respect to earth. It must be used indoors, in

an environment not exceeding pollution level 2, at an altitude of

not more than 2000m. The instrument can therefore be used in

complete safety on 400V three-phase networks in an industrial

environment.

§For safety reasons, you must use only measurement leads

having a voltage rating and category at least equal to those of

the instrument and compliant with standard IEC 61010-031.

§Do not use if the cover of the battery compartment is missing

or if the housing is damaged or not correctly closed.

§Do not place your fingers near unused terminals.

§If the instrument is used other than as specified in this

manual, the protection provided by the instrument may be

impaired.

§Do not use this instrument if it seems to be damaged.

§Check the integrity of the insulation of the leads and of the

housing. Replace damaged leads.

§Be prudent when working in the presence of voltages

exceeding 70Vdc or 33Vrms and 46.7Vpp; such voltages can

cause a risk of electrocution. The use of individual protections

is recommended in some cases.

§Always keep your hands behind the physical guards of the

probe tips or alligator clips.

§Always disconnect all leads from the measurement and from

the instrument before opening the housing.

§Always use the specified type of battery.

Office: Jl. Radin Inten II No. 62 Duren Sawit, Jakarta 13440 - Indonesia

Workshop: Jl. Pahlawan Revolusi No. 22B, Jakarta 13430 - Indonesia

Phone: 021-8690 6777 (Hunting) Fax: 021-8690 6777

Mobile: +62 816 1740 8925

English

2. UNPACKING - PACKAGING

All instruments undergo mechanical and electronic testing before

being dispatched. Every precaution is taken to ensure that the

instrument reaches you in good condition. If there is any damage,

inform the carrier immediately.

3. INTRODUCTION

The CA 6609 is designed to facilitate installing three-phase

electrical power supply networks and combines the following

functions in a single instrument:

§Determination of the direction of phase rotation;

§Presence or absence of phase ( if voltage between phases

and neutral is > 100V);

§Determination of the direction of rotation of a motor with or

without connection;

§Determination of the activation of a solenoid valve without

connection.

Office: Jl. Radin Inten II No. 62 Duren Sawit, Jakarta 13440 - Indonesia

Workshop: Jl. Pahlawan Revolusi No. 22B, Jakarta 13430 - Indonesia

Phone: 021-8690 6777 (Hunting) Fax: 021-8690 6777

Mobile: +62 816 1740 8925

English

4. DESCRIPTION OF THE INSTRUMENT

5. USING THE INSTRUMENT

5.1 DIRECTION OF PHASE ROTATION

On a three-phase electrical network:

1. Connect the 3 leads to the instrument, matching the

markings.

2. Connect the 3 alligator clips to the 3 phases of the network to

be tested.

3. Press the ON button. The green indicator indicates that the

instrument is in operation.

4. The clockwise (or anticlockwise) rotation indicator indicates

the direction of phase rotation.

1 Test lead input terminals

2 Indicators L1, L2, and L3

3 Green Clockwise rotation led

4 Red Anticlockwise rotation led

5 On/Off button

6 Green On led

7 Symbol for CA 6609 correct

orientation on themotor (§ 6)

English

Warning: the wrong direction of rotation may be displayed if a

lead is connected by mistake to the neutral of the network.

The table below (reproduced on the back of the instrument)

summarizes the various display possibilities.

Office: Jl. Radin Inten II No. 62 Duren Sawit, Jakarta 13440 - Indonesia

Workshop: Jl. Pahlawan Revolusi No. 22B, Jakarta 13430 - Indonesia

Phone: 021-8690 6777 (Hunting) Fax: 021-8690 6777

Mobile: +62 816 1740 8925

English

6. INDICATION OF THE DIRECTION OF

THE ROTATING FIELD OR

DIRECTION OF ROTATION WITHOUT

CONNECTION

1. There must be no lead connected to the instrument;

2. Position the instrument on the motor, within 2.5 cm, parallel to

the shaft in the direction indicated by the symbol on the front

panel.

3. Press the ON button. The green indicator indicates that the

instrument is in operation.

4. The clockwise or anticlockwise rotation indicator lights to

indicate the direction of the rotating field.

Note: the instrument does not work on motors controlled by

frequency converters.

Office: Jl. Radin Inten II No. 62 Duren Sawit, Jakarta 13440 - Indonesia

Workshop: Jl. Pahlawan Revolusi No. 22B, Jakarta 13430 - Indonesia

Phone: 021-8690 6777 (Hunting) Fax: 021-8690 6777

Mobile: +62 816 1740 8925

English

The table below summarizes the conditions necessary to

obtaining a reliable test result.

Number of

pairs of

poles

Number of rotations of the

rotating field (perminute)

as a function of frequency

(Hz)

Angle

between

poles

Minimum dia. of the motor

casing

16 2/3 50 60 0 cm

1 1000 3000 3600 60 5.3

2 500 1500 1800 30 10.7

3 333 1000 1200 20 16.0

4 250 750 900 15 21.4

5 200 600 720 12 26.7

6 167 500 600 10 32.1

8 125 375 450 7.5 42.8

10 100 300 360 6 53.5

12 83 250 300 5 64.2

16 62 188 225 3.75 85.6

7. DETERMINATION OF THE

DIRECTION OF CONNECTION OF

THE PHASE WIRES TO A MOTOR

1. Connect the 3 leads to the instrument, matching the

markings;

2. Connect the 3 alligator clips to the 3 phase pins of the

connector of the motor being tested;

3. Press the ON button. The green indicator indicates that the

instrument is in operation;

4. Turn the motor shaft a half-turn to the right;

5. The clockwise or anticlockwise rotation indicator lights,

indicating whether or not the order of connection of the phase

wires is correct.

Office: Jl. Radin Inten II No. 62 Duren Sawit, Jakarta 13440 - Indonesia

Workshop: Jl. Pahlawan Revolusi No. 22B, Jakarta 13430 - Indonesia

Phone: 021-8690 6777 (Hunting) Fax: 021-8690 6777

Mobile: +62 816 1740 8925

English

8. INDICATION WITHOUT

CONNECTION OF THE ACTIVATION

OF A SOLENOID VALVE

1. There must be no lead connected to the instrument;

2. Place the instrument as close as possible to the solenoid

valve;

3. Press the ON button. The green indicator indicates that the

instrument is in operation;

4. The clockwise or anticlockwise rotation indicator lights,

indicating the presence of the field generated during the

activation.

9. TECHNICAL SPECIFICATIONS

9.1 ELECTRICAL CHARACTERISTICS

Maximum rated voltage: 600V, CAT III

Operating voltage, in phases rotation use:

With connections: 40 to 600VAC between phases (see

§ 5.1 and 7)

Without connection: 120 to 400VAC between phases (see

§ 6)

Frequency of operation: 15 to 400Hz

Test current (per phase): less than 3.5mA

Power supply: 9V battery (6LR61, 6LF222, 1604A,

NEDA 1604)

Consumption less than 20mA.

L1, L2, L3 lights are on , since 100V voltage between phases and

neutral.

English

9.2 MECHANICAL CHARACTERISTICS

Dimensions (H x L x D): 130 x 69 x 32mm

Weight: 170g

9.3 ENVIRONMENTAL CHARACTERISTICS

Operating temperature: 0 to 40°C

Storage: -20°C < T < +50°C, RH < 80%

Operating relative humidity: 15 to 80%

Operating altitude: less than 2000 m

Operating pollution level: less than 2

9.4 COMPLIANCE WITH STANDARDS

IEC 61010-1, DIN VDE 0411;

IEC 61557-7, DIN VDE 0413-7;

Tightness: IP 40 (as per IEC 60529)

10. MAINTENANCE

10.1 CLEANING

Disconnect from all sources of electricity before cleaning,

servicing, dismantling.

Clean only with a soft cloth moistened with soapy water, then

plain water.

Dry completely and perfectly before using again.

Office: Jl. Radin Inten II No. 62 Duren Sawit, Jakarta 13440 - Indonesia

Workshop: Jl. Pahlawan Revolusi No. 22B, Jakarta 13430 - Indonesia

Phone: 021-8690 6777 (Hunting) Fax: 021-8690 6777

Mobile: +62 816 1740 8925

Other manuals for C.A 6609

Table of contents

Other Chauvin Arnoux Test Equipment manuals

Chauvin Arnoux

Chauvin Arnoux CA 6161 User manual

Chauvin Arnoux

Chauvin Arnoux E6N User manual

Chauvin Arnoux

Chauvin Arnoux PAC 12 User manual

Chauvin Arnoux

Chauvin Arnoux Metrix DOX2025B User manual

Chauvin Arnoux

Chauvin Arnoux C.A 6131 User manual

Chauvin Arnoux

Chauvin Arnoux C.A 6116 User manual

Chauvin Arnoux

Chauvin Arnoux C.A 6115N User manual

Chauvin Arnoux

Chauvin Arnoux pel 102 User manual

Chauvin Arnoux

Chauvin Arnoux C.A 6116N User manual

Chauvin Arnoux

Chauvin Arnoux C.A 10001 User manual

Chauvin Arnoux

Chauvin Arnoux C.A 6410 User manual

Chauvin Arnoux

Chauvin Arnoux C.A 757 User manual

Chauvin Arnoux

Chauvin Arnoux C.A 6550 User manual

Chauvin Arnoux

Chauvin Arnoux C.A 6131 User manual

Chauvin Arnoux

Chauvin Arnoux C.A 6160 User manual

Chauvin Arnoux

Chauvin Arnoux C.A 6608 User manual

Chauvin Arnoux

Chauvin Arnoux C.A 6422 User manual

Chauvin Arnoux

Chauvin Arnoux CDA 103 User manual

Chauvin Arnoux

Chauvin Arnoux C.A 6121 User manual

Chauvin Arnoux

Chauvin Arnoux C.A 6549 User manual

Chauvin Arnoux

Chauvin Arnoux C.A 8220 User manual

Chauvin Arnoux

Chauvin Arnoux C.A 6165 User manual

Chauvin Arnoux

Chauvin Arnoux HandScope CA 942 User manual

Chauvin Arnoux

Chauvin Arnoux MH 60 User manual

Popular Test Equipment manuals by other brands

SMART

SMART KANAAD SBT XTREME 3G Series user manual

Agilent Technologies

Agilent Technologies BERT Serial Getting started

Agilent Technologies

Agilent Technologies N3280A user guide

Vernier

Vernier Go Direct Voltage manual

Lifeloc

Lifeloc R.A.D.A.R. quick start guide

Fluke

Fluke T5-600 Service information

Mercury

Mercury TSL01 user manual

MAHA

MAHA MBT Series Original operating instructions

Fuji Electric

Fuji Electric P-61 instruction manual

ETC

ETC SealerAtor user manual

Skyfine

Skyfine ETHYWAY V2 user manual

Appion

Appion G5 Twin Operation manual

PCB Piezotronics

PCB Piezotronics 8159-0112A Installation and operating manual

BW Technologies

BW Technologies MicroDock II user manual

Sun Nuclear

Sun Nuclear 1027 user guide

Biomark

Biomark HPR LITE READER user manual

Hioki

Hioki 3169-20 instruction manual

Ashcroft

Ashcroft ATE-100 operating manual