Casablanca SIENA User manual

SIEIE

IEIE

IENANA

NANA

NA™™

™™

™

Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper

installation; therefore,before attempting to install and operate your Casablanca fan, read this owner’s manual completely and

carefully. Retain this manual for future reference.

CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse box

before attempting any installation procedure.

SIENA®Owner’s Manual

READ AND SAVE THESE INSTRUCTIONS!

CONTENTS

INTRODUCTION

Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Safe Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

MOUNTING RECOMMENDATIONS

General Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Sloped Ceiling Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

FAN INSTALLATION

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Crossbar Mounting Bracket Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Lag Screw Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Canopy Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Fan Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Blade Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

No Light Cap Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Hanging the Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Canopy Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Canopy Hatch Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Light Kit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

VERSA•TOUCH2™ CONTROL INSTALLATION

Control Bracket Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Changing Transmitter Frequency Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Remote Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

TROUBLESHOOTING TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

CARE RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

AUTHORIZED SERVICE CENTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

PRODUCT SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

P5G73M AA1205

Circuit Breaker

(Trip breaker for the

circuit you will be

working on)

Fuse Box

(Remove fuse for the

circuit you will be

working on)

18" ↑↑

↑↑

↑

84" ↑↑

↑↑

↑

70"↑↑

↑↑

↑

SAFE USE

•CAUTION: RISK OF ELECTRICAL SHOCK! All wiring must be performed in accordance with national and local

electrical codes. If you are unfamiliar with the wiring codes, you should use a qualified electrician. To avoid overheating

and possible damage to other equipment, do not install control to a receptacle, fluorescent light fixture, motor operated

appliance, or transformer-supplied appliance.

• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan

installations. If it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling

installations.

•This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit.The maximum

current requirement for the fan with light fixture is 3.5 amps. The fan uses about 1 amp or 100 watts. Maximum light

current is about 2.5 amps or 300 watts of total lighting.

•Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make

sure all wires are within the canopy and that no wires are being pinched.

Unpacking

Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the

parts listed in the Parts Guide. Before discarding packaging materials, be certain that all parts have been removed.

For best performance and for your warranty to be valid,

use only genuine Casablanca blades, light fixtures, and accessories.

INTRODUCTION

•The blades in each pack are matched for equal weight to

assure smooth fan operation.If more than one fan is being

installed, be careful not to mix blades from different

cartons.

•Inspect the contents of your carton for possible shipping

or handling damage. If parts are missing or damaged, call

1-888-227-2178.

•It is always a good idea to have an assistant to help with

the installation.

•When cleaning, painting, or working near your fan, be

very careful of the fan and blades. Always turn the power

OFF to the ceiling fan before working on it or replacing

lightbulbs.

•Never insert anything into the path of the fan blades while

the fan is in operation.

• Never install a fan over a pool or spa.

•Never operate a fan that has been damaged in any way.

Contact Casablanca Fan Company by calling

1-888-227-2178, or contact your local authorized

Casablanca dealer for assistance in obtaining service.

BEFORE YOU START

SIEIE

IEIE

IENANA

NANA

NA™™

™™

™

MOUNTING RECOMMENDATIONS

Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation,

and fan size are all important factors to consider before installation.

Location

Ceiling fans have practical uses in almost every room in your home.We suggest you follow these mounting recommendations

as you decide where to install your Casablanca fan.

• For safety reasons, the fan blades must be a minimum of 7' above the floor.

• Do not locate the fan in a doorway or above a swinging door.

• In bedrooms, fans work best when mounted above the foot of the bed.

• Over pool tables, be sure to provide plenty of clearance to avoid damage from pool cues.

• In kitchens be sure to allow for open cupboard doors to clear the fan blades.

• Do not install a fan close to or over a pool or spa. High humidity combined with corrosive gases will destroy the finish and

warp the blades.

Fan Size

Variable fan speed capability permits the use of a full-size 52" fan even in smaller rooms. For very large rooms, two fans may

be needed.

GENERAL GUIDELINES

Calculation of Ceiling Angle

Use the tear-off Ceiling Angle Template card inserted in

this manual. It provides you with a simple “go” or “no-go”

for installing your fan on a sloped ceiling.

7' minimum

When to Use Extension Poles

For optimum performance and appearance, an extension

pole should be used with your Casablanca fan when

installing on high (cathedral) ceilings or sloped ceilings.

Casablanca offers standard poles in increments of 6" up

to 5'. Custom poles are available in lengths up to 9'9". See

your Authorized Casablanca Dealer for details.

Blades must be a

minimum of 7 feet

above the floor

Extension

Pole

Maximum

Hang-Tru®

angle 32º

This slope is less than 32º.

It is OK to install your fan.

This slope is 32º. This is the maximum

slope that will allow the fan to hang

straight down. It is OK to install your fan.

This slope is more than 32º. Your fan will not

hang straight down, an adaptor is necessary.

Contact your local Authorized Casablanca

Dealer in regards to purchasing a “Sloped

Ceiling Adaptor.”

NOTE: Fan may wobble or vibrate if pole length is not

long enough and inside blade is too close to downslope or

side wall.Extending pole length will usually solve problem.

SLOPED CEILING INSTALLATIONS

SUGGESTED EXTENSION POLE LENGTHS

Ceiling Height Pole Length

8' 0" standard

8' 6" standard

9' 0" 6"

9' 6" 12"

10' 0" 12"

11' 0" 18"

12' 0" 24"

13' 0" 36"

14' 0" 48"

EXAMPLE 3

EXAMPLE 2

EXAMPLE 1

FAN INSTALLATION

CEILING HARDWARE (not to scale)

WARNING!

Support directly to building structure only.

WARNING!

To reduce the risk of fire, electrical shock, or

personal injury, mount to outlet box marked

“Acceptable for Ceiling Fan Support” using the

mounting hardware provided with the outlet box.

Using Existing Ceiling Fixture Outlet Box

After turning the power OFF at its source (either the circuit

breaker or fuse box), lower the old fixture and disconnect

the wiring. Check the ceiling fixture outlet box to be sure

it is marked “Approved for Ceiling Fan Mounting.”If it is

not, a new box must be installed.

GETTING STARTED

Installing a New Ceiling Fixture Outlet Box

If you do not have an existing fixture located where you

wish to place your Casablanca fan, an approved ceiling

fixture outlet box must be installed and wired.

Note: The weight of this fan is 38 pounds.

CROSSBAR MOUNTING BRACKET INSTALLATION

Note: After removing the old fixture, check the outlet

box to insure that it is supported by a joist or beam across

its upper surface. If not, a 2 x4 stud must be installed.

Step 1a. Remove the knockout plug in the center of the

outlet box or drill a 1/2-inch hole for the lag screw to pass

through.Then drill a 1/4-inch guide hole into the joist or

beam to a depth of 3 inches.

Step 1b. Route the outlet box wires through the keyhole

slot of the crossbar mounting bracket as shown. Attach

the crossbar mounting bracket to the outlet box with the

screws provided in Pack A, making sure the outlet box

wires are not pinched by the washer.

CAUTION:

To reduce the risk of personal injury, use only

the mounting hardware provided with the

approved outlet box to install the crossbar

mounting bracket.

Crossbar Mounting Bracket

Screw Pack A:

Lag Screw and Washer (1)

1" x 8-32 Roundhead Screw and Washer (2)

Wire Nut (4)

Joist

Ceiling-Fan-

Approved

Wiring Box

Ceiling Wiring

Crossbar Mounting

Bracket

Green Ground Wire

Ridge side down

1" x 8-32

Roundhead Screw

Washer

SIEIE

IEIE

IENANA

NANA

NA™™

™™

™

LAG SCREW INSTALLATION

CANOPY INSTALLATION

NOTE: This step is required only under two conditions:

If the fan weighs 36 lbs. or more or if the existing ceiling

fixture outlet box needs to be modified for a ceiling fan

application (for example, if the house is not new

construction and you are replacing an existing light fixture).

We recommend that the ceiling box be of sufficient

capacity to support the weight of the fan and light fixture

under any conditions. If in doubt whether you need to

install the lag screw, consult a qualified electrician.

Step 2. With the large washer attached, pass the lag screw

(Pack A) through the center hole of the crossbar mounting

bracket and screw into the guidehole. Tighten until the

outlet box is mounted firmly to the beam. This box must

be secured to the ceiling firmly.

Step 3. Attach the canopy to the crossbar mounting bracket

with three of the 8-32 x 21/2" long canopy screws (Screw

Pack B) and lock washers provided with your Casablanca

fan. Tighten using the provided screwdriver until snug

against the ceiling.

NOTE: On sloped ceilings, align the canopy opening

with the top or peak of the room.

CANOPY HARDWARE (not to scale)

Canopy

Canopy Hatch

Feed outlet box

wires through

canopy opening

Canopy

Lock Washer

Canopy Screw

Pack B:

Canopy Screws and Washers (5)

FAN PREPARATION

PERMA•LOCK™ HARDWARE (not to scale)

Prepare for fan installation as follows:

Step 4a. Remove the caution shield from the motor.

Step 4b. Using the provided Allen wrench (attached to

the paper motor warning shield),loosen the Allen set screw

attached to the motor coupling.

Step 4c. Slide the 9" Perma•Lock™downrod and ball

assembly through the center of the Decorative Arm

assembly.

Step 4d. Route the wires through the Perma•Lock™

downrod and ball assembly.

Step 4e. Insert the downrod into the motor coupling,

turning clockwise until it stops, ensuring that the pole

has bottomed out.

TIP: The downrod has a tapered thread that is designed

to lock completely when installed correctly.

Step 4f. Tighten the set screw with the Allen wrench to

ensure safe operation of your fan.If it is tight enough, you

should not be able to turn the downrod counterclockwise

with your hands. If in doubt, tighten the set screw with

the Allen wrench until you cannot turn it any further.

Step 4g. Tighten collar screw on Decorative Arm

Assembly to secure.

Motor Wires

(leave at least 6" long)

Ground Wire

(green)

Perma•Lock™ Downrod

and Ball Assembly

Tapered thread

Allen Wrench

Allen

Set Screw

Motor Housing

Assembly

Motor

Coupling

IMPORTANT SAFETY INFORMATION:

Before starting the installation of your ceiling

fan, install the threaded downrod into the motor

coupling and lock the assembly.

CAUTION: Failure to fully lock in the downrod

before securely tightening the Allen set screw may

cause the fan to separate from the downrod and fall

during normal operation.

Uplight Lightbulbs

(4) A-15 40-watt Allen Wrench

Decorative Arm

Assembly

9" Perma•Lock™

Downrod

and Ball Assembly

(for decorative

arm assembly

installations)

3" Perma•Lock™

Downrod

and Ball Assembly

(for non-decora-

tive arm assembly

installations)

NOTE: Installation of the Decorative Arm Assembly is

optional. For installations without the Decorative Arm

Assembly, a 3" downrod is provided.

3" Perma•Lock™ Downrod

and Ball Assembly

(for non-decorative arm

assembly installations)

Caution Shield

Decorative Arm

Assembly

SIEIE

IEIE

IENANA

NANA

NA™™

™™

™

Installation/Replacement of Incandescent Lightbulbs

Step 5. Remove the two screws from the cover door as

shown and lift door from motor. Install a 40-watt S-11

type incandescent lightbulb in the socket.Replace the door

and re-insert the screws. Repeat twice more.

NOTE: When replacing lightbulbs, be sure to use only

40-watt maximum.

BLADE INSTALLATION

Blades (5)

Allen Screw Pack C:

Blade Screws and Washers (16)

BLADE HARDWARE (not to scale)

Step 6a. Align the holes in the Siena® exclusive blade with

the holes in the bladeholder.

Step 6b. Using Screw Pack C and the Allen wrench

provided, install the Allen screws in the blade and

bladeholder as shown. Repeat for each additional blade.

CAUTION:

Blade screws must be tightened securely before

operating the fan.

NO LIGHT CAP OPTION

Note: If you are installing the accessory light fixture, skip

to Step 8a now.

Step 7a. Carefully tuck the light wires into the no light

cap, as shown.

Step 7b. Thread the no light cap into the adapter plate, as

shown.

Allen

Wrench

FAN PREPARATION (CONT.)

HANGING THE FAN

Step 8a. To hang the fan body in the canopy, hold the fan

body firmly and insert the ball into the canopy opening.

Check that no wires are pinched. Rotate the fan body until

the slot in the ball fits into the pin opposite the canopy

opening.

Step 8b. Trim excess motor wires,leaving at least 6 inches

above the downrod.Strip 1/2-inch insulation from the end

of each wire using a wire stripper (available at your local

hardware store).

Step 9. Attach the fan wires to the ceiling fixture outlet

box wiring by placing the bare ends of the wires side by

side and then securing with a wire nut. Test that the

connection is secure by pulling on the wire nut. Connect

in this order:

•GREEN leads from mounting plate and downrod

assembly of fan to GROUND conductor of power

source. Secure with wire nut.

•WHITE wire from fan to white NEUTRAL wire in

ceiling fixture outlet box. Secure with wire nut.

•BLACK power wire from fan to BLACK power wire

in ceiling outlet box. Secure with wire nut

NOTE: If the color of your ceiling wires differs from

that described, consult an electrician.

CANOPY ELECTRICAL CONNECTIONS

Step 10a. Tuck the wires into the canopy with the wire

nuts pointed upwards, so that the WHITE and BLACK

wires are on opposite sides of the canopy and all wires are

clear of the canopy opening.

Step 10b. Install the canopy hatch with the last canopy

screw and lock washer using the provided screwdriver.To

do this, tilt the fan body away from the hatch opening.

Tighten the screws firmly.

Step 10c. Straighten the fan, then check to ensure there is

no movement between the canopy and the ceiling or the

Perma•Lock™downrod and the ball assembly.

CANOPY HATCH INSTALLATION

Ball

Slot Pin

Wire Nut

2 Black

Wires

2 White

Wires

3 Green

Wires

SIEIE

IEIE

IENANA

NANA

NA™™

™™

™

LIGHT KIT INSTALLATION

Light Assembly Installation

Step 11a. Connect the light assembly connector to the

motor connector, as shown.

Step 11b. Carefully tuck the wires and align the light

assembly with the adapter plate.

Step 11c. Screw the finial rod into the adapter plate to

secure.

Install Glass Shades

Step 12a. Remove the three lock rings from the light fixture

and set aside.

Step 12b. Slide the glass shade into the fixture and hold

firmly. Using the glass locking rings removed in Step 14a,

secure each piece of glass firmly to the light fixture.

Assure each piece of glass is firmly installed by rotating

the glass clockwise until it is no longer loose.

Install Incandescent Lightbulbs

Step 13a. Screw the three 60 Watt type A15 bulbs into

each socket.

NOTE: When replacing lightbulbs, be sure to use only

60-watt maximum.

LIGHT KIT HARDWARE (not to scale)

Light Kit

Downlight Lightbulbs (3)

60-watt A-15

Glass Shade

Finial Rod

Finial

Lock Ring

Screw

6-32 X 1"

(2)

Screw

6-32 X 3/8"

(2)

Wood

Screw

1" (2)

Drywall Anchor

6-32 (2)12v Battery

W-73

Control

W-73

Control Holder

VERSA•TOUCH2™ CONTROL INSTALLATION

CONTROL BRACKET INSTALLATION

Standard Light Switch

Step A. Remove the two screws holding the switch cover

plate. Do not remove the cover plate.

Step B. Orient the control bracket as shown and line up

the two inner mounting holes with those on the switch.

Step C. Insert and tighten the screws using the provided

screwdriver.

Inner

mounting

holes

Control

Bracket

Standard

Toggle

Switch

Cover

Plate

Rocker Light Switch

Step A. Break off the two tabs by pushing outward.

Step B. Remove the two screws holding the switch cover

plate. Do not remove the cover plate.

Step C. Orient the control bracket as shown and line up

the two inner mounting holes with those on the switch.

Step D. Insert and tighten the screws using the provided

screwdriver.

Outer

mounting

holes

Control

Bracket

Rocker

Light

Switch

Cover

Plate

Wall Installation

Step A. Locate a 2x4

wall stud in a convenient

location.

Step B. Orient the

control bracket as shown

over the 2x4 stud.

Step C. Insert the 1"

wood screws in either

the inner or outer

mounting holes and

tighten using the

provided screwdriver. Decor Ovalhead Screw

6-32 X 1"

Anchor

Panhead

Screw Drywall Anchor

NOTE: The wall anchors and 6-32 x 1" screws may be

used in situations where mounting to a stud is not possible.

Use the inner mounting holes. After securing the anchor,

discard the anchor’s pointed screws and use the 6-32 decor

ovalhead screws supplied.

SAFETY FIRST: To reduce the risk of electrical shock, this fan must be installed with

an isolating wall control/switch. CAUTION! Do not use with wall dimmer.

Wood

Screw 1"

VERSA•TOUCH2™ HARDWARE (not to scale)

Step 14 Follow instructions for the type of transmitter control bracket you will be using.

This manual suits for next models

Table of contents

Other Casablanca Fan manuals

Casablanca

Casablanca Heathridge 55051 User manual

Casablanca

Casablanca La FLeur User manual

Casablanca

Casablanca Moderne User manual

Casablanca

Casablanca panama 55022 User manual

Casablanca

Casablanca Victorian User manual

Casablanca

Casablanca Capistrano Instruction manual

Casablanca

Casablanca Star User manual

Casablanca

Casablanca CONCENTRA User manual

Casablanca

Casablanca M8501-01 User manual

Casablanca

Casablanca 59153 User manual

Casablanca

Casablanca WHITMAN User manual

Casablanca

Casablanca Silhouette II User manual

Casablanca

Casablanca M8513-01 User manual

Casablanca

Casablanca 4TS26IIRB User manual

Casablanca

Casablanca 55082 User manual

Casablanca

Casablanca Caneel Bay Instruction manual

Casablanca

Casablanca Brescia Casablanca Brescia Gallery Edition User manual

Casablanca

Casablanca UTOPIAN User manual

Casablanca

Casablanca 59287 Instruction manual

Casablanca

Casablanca Malibu Star User manual

Casablanca

Casablanca Vita User manual

Casablanca

Casablanca ALESSANDRIA User manual

Casablanca

Casablanca C42GxxxL User manual

Casablanca

Casablanca ainsworth 54000 Technical Document

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual