CAS PD-II User manual
9002-PD2-0033-0
2003. 08
PD-
ECR Interface Scale
OWNER’S MANUAL
CONTENTS
PRECAUTIONS 4
PREFACE 6
NAMES AND FUNCTIONS 6
OPERATIONS 8
1. General Weighing 8
2. Weighing With Tare 9
3. ECR Interface 9
ERROR MESSAGE 11
SPECIFICATIONS 11
45
For consistent and accurate reading,
maintain periodical check by your
CAS authorized dealer.
Avoid sudden shock to the scale.
Internal mechanism could be damaged.
Place the scale on firm and temperature
consistent environment.
Keep the scale away from other
electromagnetic generating devices.
This may interfere with accurate
reading.
Grab on the bottom of the scale when
moving. Do not hold by the platter.
Attention
If the scale is not properly level, please adjust
the 4 legsat the bottom of the scale
(turn legs clockwise or counterclockwise)
so as to center the bubble of
the leveling gauge
inside the indicated
circle.
Do not disassemble the scale.
When any damage or defect occurs,
contact your CAS
authorized dealer
immediately for
proper repair.
Do not overload beyond the maximum
weight limit.
Do not pull the plug by its cord when
unplugging. Damaged cord could cause
electric shock or fire.
To prevent from fire occurring, Do not
place or use the scale near flammable or
corrosive gas.
Avoid placing the scale near heater
or in direct sunlight.
Scale must be grounded to minimize
electricity static. This will minimize
defect or electric shock.
Insert plug firmly to wall outlet to
prevent electric shock.
To reduce electric shock or incorrect
reading, Do not spill water on the scale
or place it in humid condition.
Warning
PRECAUTIONS
To ensure that you get the most from your scale, please follow these
instruction.
Make sure to plug your scale into the proper power outlet. For maximum
performance,plugintoapoweroutlet30minutesbeforetheusageforwarmup.
7
6
PREFACE
NAMES AND FUNCTIONS
Thank you for purchasing our CAS PD-II.
These series have been designed with CAS reliability, under rigid quality control
and with outstanding performance. Your specialty departments can enjoy these
high quality reliable CAS products.
We believe that your needs will be satisfied and you will have proper reliability.
This manual will help you with proper operation and care of the PD-II.
Please keep it handy for future reference.
OVERALL VIEW
PLATTER
DISPLAY
ADJUSTING BOLT
< STANDARD TYPE >
CUSTOMER
DISPLAY
KEYBOARD
POWER SWITCH PARALLEL PORT RS232
PLATTER
DISPLAY
ADJUSTING BOLT
POLE TYPE
DISPLAY CABLE
POLE TYPE DISPLAY
KEYBOARD
< POLE TYPE >
DISPLAY
9
8
Place an item in the container.
To release the TARE function, remove an item and container
from the platter and press the key.
Make sure that power is OFF. While pressing key,
turn on the power. “EcrSEt” is shown on the disply. And then
current ECR type is shown on the display as “tYPE-2”.
3. ECR Interface
PD-II can interface with most ECRs by selecting TYPE 0 to TYPE 6.
ECR Type Selection
OPERATIONS
1. General Weighing
The display indicates if the scale is at zero or if there is a tare entered into the
scale by way of a ZERO and NET.
When the display is not zero though there is nothing on the platter, press the
key.
Turn on the power. The display shows 0.00 or 0.000.
Make sure that ST(Stable) and ZERO lamps are On.
Place an item on the platter. When the ST(Stable) lamp is
0n, read the weight.
Place the container on the platter.
Press the key, NET lamp is On.
2. Weighing with Tare
There is the weight of container being used for a commodity.
The key subtracts the weight of the container.
KEY FUNCTIONS
Used to set the zero point to 0.00 or 0.000.
Used as ENTER key in Setup Mode.
Used to enter a tare weight and used to cancel a tare weight.
Used as ESC key in Setup Mode.
No function
KEY DESCRIPTION
If you select ECR type 5, press the *key until the display
shows “tYPE-5”. (Refer to Table 1.)
11
10
SPECIFICATIONS
MODEL
CAPACITY
INTERNAL RESOLUTION
EXTERNAL RESOLUTION
TARE SUBTRACTION
DISPLAY
DISPLAY LAMP
INTERFACE
PRODUCT SIZE
PLATTER SIZE
OPERATING
TEMPERATURE RANGE
POWER SOURCE
PDll - 6(R) PDll - 15(R) PDll - 30(R) PDll - 60(R)
6kg/2g 15kg/5g 30kg/10g 60kg/20g
1/90,000 1/90,000 1/90,000 1/90,000
1/3,000 1/3,000 1/3,000 1/3,000
- 6.000kg - 15.000kg - 30.00kg - 60.00kg
VFD 6 DIGIT
ST, ZERO, NET
RS - 232C, 4-Bit Parallel Communication. (ECR Interface)
380 280 79 [mm]
380 280 [mm]
10°C 40°C
AC 230V / 50Hz
ERROR MESSAGE
Failure of A/D Module
An error of initial zero range
Call your CAS dealer
Set the platter empty
Make sure there is a platter on the scale
ERROR REASONS SOLUTIONS
Err
Err 1
Most POS, ECRs and Some
TEC POS System
Sharp ER-Axxx, New Sanyo
ECRs using RS-232 others
Most POS System
Samsung, CRS, NCR2170 and
other ECRs
NCI General.
Most POS Software
Samsung ER-670
TEC 4 Digit 4Bit Parallel
(New kg)
TEC 4 Digit 4Bit Parallel
(Old kg)
Universal 4 Bit Parallel
ECR-TYPE 0
ECR-TYPE 1
ECR-TYPE 2
ECR-TYPE 3
ECR-TYPE 4
ECR-TYPE 5
ECR-TYPE 6
key
Description
MENU 4-Bit Parallel RS-232 Serial
Serial Communication
9600 Baud Rate, 7 Date bit, Even Parity. 1 Stop bit
Table 1.
To save current ECR type, press the key.
Other manuals for PD-II
5
Table of contents
Other CAS Scale manuals
CAS
CAS Road Weigher RW-2601P User manual
CAS
CAS BFA-2 User manual
CAS
CAS SC Series User manual
CAS
CAS CL5000J Series User manual
CAS
CAS HE-30B User manual
CAS
CAS LP-1000N Series User manual
CAS
CAS PR-C series User manual
CAS
CAS CL7200 series Owner's manual
CAS
CAS DL-30 User manual
CAS
CAS SW-1S Series User manual
CAS
CAS PDN Series User manual
CAS
CAS S2000 Jr. Series User manual
CAS
CAS LP 1.6 Series User manual
CAS
CAS S2000JR User manual
CAS
CAS ER PLUS SERIES User manual
CAS
CAS HE-13 User manual
CAS
CAS CL7200 series User manual
CAS
CAS PR-II User manual
CAS
CAS RETAIL WEIGHING SOLUTION CT100 User manual
CAS
CAS AP-US Series User manual
