Canarm AgSystems PF52 User manual
WARRANTY
Canarm Ltd. warrants every new fan to be free of defects and workmanship, to the extent that, within one year from the date of
purchase, Canarm Ltd. shall either repair or replace at Canarm’s option, any unit or part thereof, returned freight pre-paid, and
found to be defective. Proof of purchase may be required.
This warranty does not include any labor or transportation cost incidental to the removal and re-installation of the unit at the
users premises.
Components repaired or replaced are warranted through the remainder of the original warranty period only.
This warranty applies to the original purchaser - user only; it is null and void in case of alteration, accident, abuse, neglect, and
operation not in accordance with instructions.
NOTICE: No warranty claims will be honored by Canarm Ltd. unless prior authorization is obtained.
Installation or Product problems? Do not return to store of purchase.
Contact Canarm Service at 1-800-265-1833 (CANADA) 1-800-267-4427 (U.S.A.)
1-800-567-2513 (EN FRANCAIS) Monday to Friday 8:00 - 5:00pm e.s.t.
or visit www.canarm.com
PF52 Fans
Instruction Manual
READ AND SAVE THESE INSTRUCTIONS
PF52-M - 03/16/12 Page 1 of 5
Models:
PF52-AI
PF52-A3
MOVE OUT BLADE TO END OF SHAFT BEFORE STARTING FAN.
MAKE SURE BLADE IS TIGHTENED UP AFTERWARDS.
WARNING!
PF52-M - 03/16/12 Page 2 of 5
Congratulations on the purchase of this innovative
circulating fan.
Its new design allows it to easily mount to walls, posts or
ceilings.
This fan provides 28,000 CFM of circulating air flow - good
for any application.
If your PF52 comes assembled, you will only require the
mounting bracket and U-bolts. If unassembled, your
package should include the items listed below and right..
Please check to ensure you have these parts before
assembly.
DIAGRAM 1
HARDWARE INCLUDED
WARNING:
THE FAN MUST BE MOUNTED TO THE BUILDING STRUCTURE.
THE STRUCTURE MUST BE SUITABLE TO SUPPORT THE WEIGHT OF THE FAN.
WARNING:
THE HARDWARE FOR MOUNTING TO JOIST OR BEAM IS NOT SUPPLIED. HARDWARE USED MUST BE
SUITABLE FOR THE TYPE OF JOIST OR BEAM TO WHICH THE FAN WILL BE MOUNTED. HARDWARE
MUST CORRECTLY FIT THE MOUNTING HOLES PROVIDED AND SUPPORT THE WEIGHT OF THE FAN.
WARNING:
FAILURE TO TIGHTEN ALL BOLTS & NUTS SECURELY COULD RESULT IN SERIOUS INJURY!
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID STATE
SPEED CONTROL DEVICE.
CONNECTING FRAME TO ORIFACE
FAN BACK VIEW
PF52 FANS
STEP 1
Begin by fastening the main panel frame to the orifice, using bolts M8x55 (14) and M8x35 (4). See DIAGRAMS 1 & 2.
DIAGRAM 2
READ INSTRUCTIONS COMPLETELY BEFORE INSTALLATION & SAVE FOR REFERENCE
PARTS LIST
PF52-M - 03/16/12 Page 3 of 5
Mount the fan blade onto the fan shaft. Loosen the
two bolts on the fan blade prior to attaching. When
mounted, hand tighten these bolts. After final
alignment is established these bolts will be tightened
further.
STEP 5
Attach the two Pillow Block Bearings using M10x40
(4) to the shaft bracket. Insert the fan shaft into the
two pillow block bearings. The shaft should protrude
slightly longer on the front of the fan vs. the back of
the fan where the large pulley attaches.
STEP 4
Connect the shaft bracket (plate that is approx. ½
the width of motor mounting bracket) below the
motor mounting bracket, directly above the
mounting plate, using M8x40 (4).
STEP 3
Connect the motor bracket (plate with the oval
cut-out center) in between the two uprights centered
in the top of the frame, using M8x40 (4). Please
notice the flat mounting plate should be on the
bottom of the frame. See Diagram 3.
STEP 2
Attach the large pulley to fan shaft on the opposite
side of the fan blade. Be certain the center of the
large pulley is aligned straight up with the large oval
of the motor bracket. Once alignment is established
tighten two set screws on the large pulley.
See Diagram 4.
STEP 6
The fan blade needs to be aligned with the orifice
opening so the blade edge does not stick past the
edge of the orifice. Once aligned, tighten the set
screws.
STEP 7
Mount the Tensioner bracket on the back right side
of the shaft mount using M8x25 (2).
See Diagram 5.
STEP 8
FAN BACK VIEW
DIAGRAM 3
DIAGRAM 4
PF52-M - 03/16/12 Page 4 of 5
Attach the small pulley to the motor shaft. Be certain
the small pulley aligns straight with the large pulley.
See Diagram 6.
STEP 11
Place the MX V4 belt around the small pulley, sliding
onto the large pulley and tensioner in one motion.
Note: rotating the wheel and pressing the tensioner
closer to the wheel will allow the belt to mount easier
on the pulleys.
STEP 12
If using the panel mounting kit, bolt the universal wall
mounts to the wall or beam that will hold the base of
the mount. Next, place the U bolts in the appropriate
holes to hold the L mount in place.
STEP 13
The L mount end will slide through the U bolts on the
mounting plate located on the bottom of the panel
fan frame. Tighten the U-Bolts once the desired
position has been established.
STEP 14
Mount motor to the motor bracket. Fasten with
appropriate bolts.
STEP 10
DIAGRAM 5
DIAGRAM 6
Mount the Tensioner onto the Tensioner bracket
using one M10 bolt.
STEP 9
USE & CARE
Fan Controls:
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID
STATE SPEED CONTROL DEVICE.
PF52-M - 03/16/12 Page 5 of 5
MAINTENANCE
These fans are used in a variety of applications and therefore maintenance schedules will vary. In general no more than 1/16" of dirt
build-up should occur on blade, motor and guard for proper fan operation and to prevent premature failure. The complete fan should
be wiped down on a regular basis to maintain the high efficiency of the fan. Particular care should be taken to clean fan blades front
and back, and guards for better air moving performance. The motor should be kept clean to prevent overheating and premature failure.
As with all mechanical equipment scheduled inspections should include checking that all hardware is secure and blade set screws are
tight. We suggest as a minimum, that this be performed at the start and twice more every season.
!
WARNING:
MOTORS ARE EQUIPPED WITH AUTOMATIC OVERLOAD PROTECTION AND MAY RESTART WITHOUT
WARNING. ALWAYS DISCONNECT FROM POWER BEFORE ATTEMPTING TO SERVICE.
Moving parts,
disconnect power
before servicing.
WARNING:
DO NOT PRESSURE WASH THE MOTOR. THE MOTOR IS TOTALLY ENCLOSED, BUT IT IS NOT
SEALED.
CANARM LTD. CANARM LTEE. ARTHUR MANUFACTURING FACILITY
2157 PARKEDALE AVE., PO BOX 367 2555 RUE BERNARD LEFEBVRE #7686 CONCESSION 16, RR4
BROCKVILLE, ONTARIO K6V 5V6 LAVAL, QUEBEC H7C 0A5 ARTHUR, ONTARIO N0G 1A0
TELEPHONE: (613) 342-5424 TELEPHONE: (450) 665-2535 TELEPHONE: (519) 848-3910
FAX: 1-800-263-4598 FAX: (450) 665-0910 FAX: (519) 848-3948
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
A) Use this unit only in the manner intended by the manufacturer. If you have questions, contact
the manufacturer.
B) Before servicing or cleaning unit, switch power off at service panel and lock the service
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a prominent warning device, such as a
tag to the service panel.
CAUTION:
TIE OFF THE EXCESS CORD SO THAT IT WILL NOT GET CUT IN THE FAN.
WARNING:
ALL WIRING SHOULD BE PERFORMED BY A QUALIFIED ELECTRICIAN FOLLOWING LOCAL CODES
AND REGULATIONS.
This manual suits for next models
2
Table of contents
Other Canarm Fan manuals
Canarm
Canarm SD08 User manual
Canarm
Canarm CITIE User manual
Canarm
Canarm Industrial User manual
Canarm
Canarm AXIS User manual
Canarm
Canarm HAF18 User manual
Canarm
Canarm GSF Series User manual
Canarm
Canarm Standard exhaust fans User manual
Canarm
Canarm AgSystems PRF36 User manual
Canarm
Canarm AgSystems MAX-AIR PLUS User manual
Canarm
Canarm 3000M Series User manual
Canarm
Canarm HAF16-ZO-WOSC User manual
Canarm
Canarm BUILDER User manual
Canarm
Canarm SKYLAR User manual
Canarm
Canarm NOUVEAU User manual
Canarm
Canarm CPF Series User manual
Canarm
Canarm CJF - AC Series User manual
Canarm
Canarm SD08-EC User manual
Canarm
Canarm PLF Series User manual
Canarm
Canarm CF1770 User manual
Canarm
Canarm XFS10 User manual
Popular Fan manuals by other brands
ELTA FANS
ELTA FANS H03VV-F installation guide
Hunter
Hunter 20714 Owner's guide and installation manual
Emerson
Emerson CARRERA VERANDA CF542ORB00 owner's manual
Hunter
Hunter Caraway Owner's guide and installation manual
Panasonic
Panasonic FV-15NLFS1 Service manual
Kompernass
Kompernass KH 1150 operating instructions
