Cabletron Systems BRIM-T6 User manual

BRIM-T6

USER’S GUIDE

NOTICE

Cabletron Systems reserves the right to make changes in speciﬁcations and other

information contained in this document without prior notice. The reader should in all cases

consult Cabletron Systems to determine whether any such changes have been made.

The hardware, ﬁrmware, or software described in this manual is subject to change without

notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FORANY

INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES

WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING

OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED

IN IT, EVEN IF CABLETRON SYSTEMS HAS BEENADVISED OF, KNOWN, OR

SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

P.O. Box 5005, Rochester, NH 03866-5005

Printed in the United States of America

Order Number: 9031288 September 1995

LANVIEW

Remote

LANVIEW

SPECTRUM

BRIM

TPIM-T1

TPIM-T2

TPIM-T4

TPIM-F2

TPIM-F3

, and

MicroMMAC

are trademarks of Cabletron

Systems, Inc.

CompuServe

is a registered trademark of CompuServe, Inc.

Intel

is a registered trademark of the Intel Corporation.

Printed on recycled paper.

NOTICE

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired

operation.

NOTE:

This equipment has been tested and found to comply with the limits for a ClassA

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment uses, generates, and can radiate radio frequency

energy and if not installed in accordance with the operator’s manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause interference in which case the user will be required to correct the

interference at his own expense.

WARNING:

Changes or modiﬁcations made to this device which are not expressly

approved by the party responsible for compliance could void the user’s authority to operate

the equipment.

DOC NOTICE

This digital apparatus does not exceed the ClassA limits for radio noise emissions from

digital apparatus set out in the Radio Interference Regulations of the Canadian Department

of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la class A prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des Communications du Canada.

VCCI NOTICE

This equipment is in the 1st Class Category (information equipment to be used in

commercial and/or industrial areas) and conforms to the standards set by the Voluntary

Control Council for Interference by Information Technology Equipment (VCCI) aimed at

preventing radio interference in commercial and/or industrial areas.

Consequently, when used in a residential area or in an adjacent area thereto, radio

interference may be caused to radios and TV receivers, etc.

Read the instructions for correct handling.

NOTICE

iii

PROGRAM LICENSE AGREEMENT

IMPORTANT:

Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems, Inc.

(“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron

software program (the “Program”) contained in this package. The Program may be

contained in ﬁrmware, chips or other media. BY UTILIZING THE ENCLOSED

PRODUCT,YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS

AGREEMENT, WHICH INCLUDES THE LICENSE AND THE LIMITATION OF

WARRANTY AND DISCLAIMER OF LIABILITY. IFYOU DO NOT AGREE TO THE

TERMS OF THISAGREEMENT, PROMPTLY RETURNTHE UNUSED PRODUCT TO

THE PLACE OF PURCHASE FORA FULL REFUND.

CABLETRON SOFTWARE PROGRAM LICENSE

1. LICENSE.You have the right to use only the one (1) copy of the Program provided in

this package subject to the terms and conditions of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as permitted

by the Copyright Act of the United States or as authorized in writing by Cabletron.

2. OTHER RESTRICTIONS.You may not reverse engineer, decompile, or disassemble

the Program.

3. APPLICABLE LAW. This LicenseAgreement shall be interpreted and governed

under the laws and in the state and federal courts of New Hampshire.You accept the

personal jurisdiction and venue of the New Hampshire courts.

NOTICE

EXCLUSION OFWARRANTY & DISCLAIMER OF

LIABILITY

1. EXCLUSIONOFWARRANTY.Except as may be speciﬁcally providedby Cabletron

in writing, Cabletron makes no warranty, expressed or implied, concerning the

Program (including Its documentation and media).

CABLETRON DISCLAIMSALL WARRANTIES, OTHER THAN THOSE

SUPPLIED TOYOU BY CABLETRON IN WRITING, EITHER EXPRESS OR

IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF

MERCHANTABLITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH

RESPECT TO THE PROGRAM, THEACCOMPANYING WRITTEN

MATERIALS, AND ANY ACCOMPANYING HARDWARE.

2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL

CABLETRON OR ITS SUPPLIERS BE LIABLE FORANY DAMAGES

WHATSOEVER(INCLUDING,WITHOUT LIMITATION,DAMAGESFOR LOSS

OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS

INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE

DAMAGES, OR OTHER LOSS)ARISING OUT OF THE USE OR INABILITY TO

USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME

STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY

FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR ON THE

DURATION OR LIMITATION OF IMPLIED WARRANTEES IN SOME

INSTANCESTHEABOVELIMITATIONSANDEXCLUSIONSMAYNOTAPPLY

TOYOU.

UNITED STATES GOVERNMENT RESTRICTED

RIGHTS

The enclosed product (a) was developed solely at private expense; (b) contains “restricted

computer software” submitted with restricted rights in accordance with Section 52227-19

(a) through (d) of the Commercial Computer Software - Restricted Rights Clause and its

successors, and (c) in all respects is proprietary data belonging to Cabletron and/or its

suppliers.

For Department of Defense units, the product is licensed with “Restricted Rights” as

deﬁned in the DoD Supplement to the Federal Acquisition Regulations, Section

52.227-7013 (c) (1) (ii) and its successors, and use, duplication, disclosure by the

Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights

in Technical Data and Computer Software clause at 252.227-7013. Cabletron Systems,

Inc., 35 Industrial Way, Rochester, New Hampshire 03867

CONTENTS

CHAPTER 1 INTRODUCTION

1.1 USING THIS MANUAL. . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

1.2 INTRODUCING THE BRIM-T6 . . . . . . . . . . . . . . . . . . . . .1-2

1.3 BRIM SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

1.4 RELATED DOCUMENTATION. . . . . . . . . . . . . . . . . . . . . .1-4

1.5 GETTING HELP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

CHAPTER 2 INSTALLATION

2.1 UNPACKING THE BRIM-T6. . . . . . . . . . . . . . . . . . . . . . . .2-1

2.2 INSTALLING THE BRIM-T6. . . . . . . . . . . . . . . . . . . . . . . .2-1

2.2.1 Installing the BRIM-T6 into a MIM . . . . . . . . . . . . .2-2

2.2.2 Installing the BRIM-T6 into a Standalone Device. .2-4

2.3 CONFIGURING THE BRIM-T6 RING SPEED. . . . . . . . . .2-4

2.4 CONFIGURING AND INSTALLING TPIMs . . . . . . . . . . . .2-6

2.4.1 Conﬁguring TPIMs . . . . . . . . . . . . . . . . . . . . . . . . .2-6

2.4.2 Installing TPIMs . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

CHAPTER 3 CONNECTINGTOTHE NETWORK

3.1 CONNECTING STP SEGMENTS . . . . . . . . . . . . . . . . . . .3-1

3.2 CONNECTING UTP SEGMENTS . . . . . . . . . . . . . . . . . . .3-2

3.3 CONNECTING FIBER OPTIC SEGMENTS . . . . . . . . . . .3-2

CHAPTER 4 MONITORING ANDTROUBLESHOOTING

4.1 LANVIEW LEDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

4.1.1 Describing BRIM-T6 LEDs. . . . . . . . . . . . . . . . . . .4-1

4.2 CHECKING THE CONNECTION. . . . . . . . . . . . . . . . . . . .4-3

APPENDIX A TPIM SPECIFICATIONS

A.1 TWISTED PAIR TPIM PINOUTS: STATION MODE. . . . . .A-1

A.2 FIBER OPTIC TPIM SPECIFICATIONS . . . . . . . . . . . . . .A-1

CONTENTS

APPENDIX B MEDIA SPECIFICATIONS AND

REQUIREMENTS

B.1 FIBER OPTIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1

B.2 SHIELDED TWISTED PAIR (STP) . . . . . . . . . . . . . . . . . .B-2

B.3 UNSHIELDED TWISTED PAIR (UTP). . . . . . . . . . . . . . . .B-3

1-1

CHAPTER 1

INTRODUCTION

Welcome to the

BRIM-T6 USER’S GUIDE

. This manual describes

BRIM-T6features,installationinstructions,and operating procedures.Itis

intended for all users of the BRIM-T6.

1.1 USINGTHIS MANUAL

If you are unfamiliar with Cabletron Systems’networking products, please

read this manual completely to gain an understanding of the features and

capabilities of the BRIM-T6. Also, you should have a general knowledge

of Token Ring (IEEE 802.5) data communications networks and their

physical layer components before operating the BRIM-T6.

This manual is organized as follows:

Chapter 1,

Introduction

, outlines the contents of this manual and

discusses BRIM-T6 features, capabilities, and speciﬁcations. It also

describes how to get technical help and lists related documentation.

Chapter 2,

Installation

, describes how to conﬁgure and install the

BRIM-T6 and Token Ring Port Interface Modules (TPIMs).

Chapter 3,

Connecting to the Network

, describes how to establish the

physical link to a Local Area Network (LAN) by connecting standard

network cable segments to the BRIM-T6.

Chapter 4,

Monitoring and Troubleshooting

, describes how to use

the

LANVIEW LEDs diagnostic system to monitor the BRIM-T6’s

operational status. It also describes procedures for resolving problems

encountered establishing a link to a network via the BRIM-T6 interface.

AppendixA,

TPIM Speciﬁcations

, describes speciﬁcations for Cabletron

Systems’series of attachable TPIMs.

Appendix B,

Media Speciﬁcations

, describes speciﬁcations for network

media.

INTRODUCTION

1-2

1.2 INTRODUCINGTHE BRIM-T6

TheBRIM-T6(seeFigure 1-1)is a SNMP-manageabledaughterboardthat

provides a bridging and routing interface for a variety of Cabletron

Systems’Intel i960-based intelligent Token Ring and Ethernet host

devices (for example, the MicroMMAC-T concentrator and the EMM-E6

management module).

Figure 1-1. BRIM-T6

NOTE

: Contact your Cabletron Representative for up-to-date information

about products that support the BRIM-T6.

Media Flexibility

Used in conjunction with Cabletron Systems’series of hot swappable

TPIMs, the BRIM-T6 can be conﬁgured for connection to all standard

network media. See Section 2.4 for instructions on how to conﬁgure and

install TPIMs. Table 1-1 lists TPIMs and their corresponding media and

connector types.

Table 1-1. TPIMs and Corresponding Media

TPIM Corresponding Media Connector

TPIM-T1

Shielded Twisted Pair DB9

TPIM-T2

Unshielded Twisted Pair RJ45

TPIM-T4

Shielded Twisted Pair RJ45

TPIM-F2

Multimode Fiber Optic ST

TPIM-F3

Single-mode Fiber Optic ST

BRIM T6

16Mb XMT

STB RCV

Table of contents

Other Cabletron Systems Network Hardware manuals

Cabletron Systems

Cabletron Systems SSIM-A2-01 User manual

Cabletron Systems

Cabletron Systems WPIM T1 User manual

Cabletron Systems

Cabletron Systems Device Management Module Dec GigaSwitch User manual

Cabletron Systems

Cabletron Systems 9E132-15 Technical document

Cabletron Systems

Cabletron Systems TRMIM-22 User manual

Cabletron Systems

Cabletron Systems TRBMIM-T User manual

Cabletron Systems

Cabletron Systems VHSIM-G02 User manual

Cabletron Systems

Cabletron Systems 9F241-12 Technical document

Cabletron Systems

Cabletron Systems WPIM-DI Installation and maintenance instructions

Cabletron Systems

Cabletron Systems 6C105 Operation and maintenance manual

Cabletron Systems

Cabletron Systems SWPIM-E1 User manual

Cabletron Systems

Cabletron Systems CyberSWITCH HSIM-W6 User manual

Cabletron Systems

Cabletron Systems 1082 User manual

Cabletron Systems

Cabletron Systems BRIM F6 BRIM-F6 User manual

Cabletron Systems

Cabletron Systems 6E122-26 User manual

Cabletron Systems

Cabletron Systems MMAC-Plus 9A128-01 Programming manual

Cabletron Systems

Cabletron Systems Cabletron BRIM-F6 User manual

Cabletron Systems

Cabletron Systems CRBRIM-W/E User manual

Cabletron Systems

Cabletron Systems TRBMIM User manual

Cabletron Systems

Cabletron Systems SWPIM-BRI User manual

Cabletron Systems

Cabletron Systems CRBRIM-W/T Installation manual

Cabletron Systems

Cabletron Systems BRIM-W6 User manual

Cabletron Systems

Cabletron Systems MMAC-5FNB User manual

Cabletron Systems

Cabletron Systems ATX Manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide