Cabletron Systems 9E429-36 Quick start guide

9032034-01

SmartSwitch 9000

9E428-12/36 and 9E429-12/36

Local Management Appendix

Appendix

9E428-12/36 and 9E429-12/36

Module Speciﬁc Information

Introduction

This appendix contains local management information that is speciﬁc to the

following Ethernet modules:

• 9E428-12 (12 Ports, Multimode Fiber, ST connectors)

• 9E428-36 (36 Ports, Multimode Fiber, ST connectors)

• 9E429-12 (12 Ports, Single-Mode Fiber, ST connectors)

• 9E429-36 (36 Ports, Single-Mode Fiber, ST connectors)

The 9E428-12 and 9E429-12 Ethernet Modules are 13-port switching modules

with:

• 12 front panel Ethernet ports

• 1 Internal Network Bus (INB) backplane port

The 9E428-36 and 9E429-36 Ethernet Modules are 37-port switching modules

with:

• 36 front panel Ethernet ports

• 1 Internal Network Bus (INB) backplane port

Each front-panel port of the 9E428-12/36 and 9E429-12/36 can be conﬁgured to

operate in the Full Duplex mode. This conﬁguration allows each port to provide a

full 20 Mbps of bandwidth.

9E428-12/36 and 9E429-12/36 Module Speciﬁc Information

Modifying Fields and User Privileges

To modify ﬁelds on these modules, you must have read-write or super-user

privileges. If you have read-only privileges, you can view information; however,

you cannot modify any ﬁelds. For more information about user privileges and

community names, see the

SmartSwitch 9000 Module Local Management User’s

Guide.

Module Interface Codes

The 9E428-36 and 9E429-36 Ethernet Modules have 41 interfaces. The 9E428-12

and 9E429-12 Ethernet Modules have 17 interfaces. Table 1 lists the identifying

number, name, and description of each interface.

Table 1. 9E428-36 and 9E429-36 Module Interface Codes

Interface

Number

Interface

Name

Interface

Description

1 SMB1 1 Mbps System Management Bus

2 SMB10 10 Mbps System Management Bus

3 HOST i960 Host

4 LOCAL i960 Controller

5 INB Internal Network Bus

6 ENET1 Ethernet Front Panel Port 1

7 ENET2 Ethernet Front Panel Port 2

8 ENET3 Ethernet Front Panel Port 3

9 ENET4 Ethernet Front Panel Port 4

10 ENET5 Ethernet Front Panel Port 5

11 ENET6 Ethernet Front Panel Port 6

12 ENET7 Ethernet Front Panel Port 7

13 ENET8 Ethernet Front Panel Port 8

14 ENET9 Ethernet Front Panel Port 9

15 ENET10 Ethernet Front Panel Port 10

16 ENET11 Ethernet Front Panel Port 11

17 ENET12 Ethernet Front Panel Port 12

9E428-12/36 and 9E429-12/36 Module Speciﬁc Information

Use the numbers listed in Table 1 to conﬁgure the module’s default interface (see

the General Conﬁguration Screen).

18 ENET13 Ethernet Front Panel Port 13

19 ENET14 Ethernet Front Panel Port 14

20 ENET15 Ethernet Front Panel Port 15

21 ENET16 Ethernet Front Panel Port 16

22 ENET17 Ethernet Front Panel Port 17

23 ENET18 Ethernet Front Panel Port 18

24 ENET19 Ethernet Front Panel Port 19

25 ENET20 Ethernet Front Panel Port 20

26 ENET21 Ethernet Front Panel Port 21

27 ENET22 Ethernet Front Panel Port 22

28 ENET23 Ethernet Front Panel Port 23

29 ENET24 Ethernet Front Panel Port 24

30 ENET25 Ethernet Front Panel Port 25

31 ENET26 Ethernet Front Panel Port 26

32 ENET27 Ethernet Front Panel Port 27

33 ENET28 Ethernet Front Panel Port 28

34 ENET29 Ethernet Front Panel Port 29

35 ENET30 Ethernet Front Panel Port 30

36 ENET31 Ethernet Front Panel Port 31

37 ENET32 Ethernet Front Panel Port 32

38 ENET33 Ethernet Front Panel Port 33

39 ENET34 Ethernet Front Panel Port 34

40 ENET35 Ethernet Front Panel Port 35

41 ENET36 Ethernet Front Panel Port 36

Table 1. 9E428-36 and 9E429-36 Module Interface Codes (Continued)

Interface

Number

Interface

Name

Interface

Description

9E428-12/36 and 9E429-12/36 Module Speciﬁc Information

Full Duplex Conﬁguration Screen

The 9E428-12/36 and 9E429-12/36 Full Duplex Conﬁguration Screen

(Figure 1), displays the port number, operation mode, link status, and port status

of the module’s ports (12 ports at a time).

Figure 1. 9E428-12/36 and 9E429-12/36 Full Duplex Conﬁguration Screen

SmartSwitch 9000 Local Management

Full Duplex Configuration

Module Name: 9E428-36 Firmware Revision: 01.04.07

Slot Number: 9 BOOTPROM Revision: 01.01.01

PORT# OPERATION MODE LINK STATUS PORT STATUS

1 STANDARD ENET No Link ENABLED

2 STANDARD ENET No Link ENABLED

3 STANDARD ENET No Link ENABLED

4 STANDARD ENET No Link ENABLED

5 STANDARD ENET No Link ENABLED

6 STANDARD ENET No Link ENABLED

7 STANDARD ENET No Link ENABLED

8 STANDARD ENET No Link ENABLED

9 STANDARD ENET No Link ENABLED

10 STANDARD ENET No Link ENABLED

11 STANDARD ENET No Link ENABLED

12 STANDARD ENET No Link ENABLED

SAVE [ 13-24 ] SET ALL PORTS: FULL EXIT RETURN

9E428-12/36 and 9E429-12/36 Module Speciﬁc Information

Full Duplex Conﬁguration Screen Fields

The following information brieﬂy explains each Full Duplex Conﬁguration Screen

ﬁeld.

OPERATION MODE (Modiﬁable)

Indicates whether the speciﬁed port will transmit and receive data separately or

simultaneously. You can set this ﬁeld to one of the following values:

• STANDARD ENET - The port can either transmit data or receive data, but not

both at the same time. Therefore, the port is running at 10 Mbps (this is the

default

• FULL DUPLEX - The port can transmit and receive data at the same time.

Therefore, the port is running at 20 Mbps.

LINK STATUS

Indicates whether there is a physical connection from this port to another 10Base-

FL device. One of the following values appears:

• Link - There is a 10Base-FL link signal present; there is a valid physical

connection from this port to another 10Base-FL device.

• No Link - There is no 10Base-FL link signal present; there is no valid physical

connection from this port to another 10Base-FL device.

PORT STATUS

Indicates whether the port has been turned on or off administratively. You will see

one of the following values:

• ENABLED - The port is turned on administratively.

• DISABLED - The port is turned off administratively.

Enable or disable ports from the Bridge Conﬁguration screen.

NOTE

9E428-12/36 and 9E429-12/36 Module Speciﬁc Information

Displaying Information About Other Ports

To display information about other ports:

1. Use the arrow keys to highlight one of the following ﬁelds (located at the

bottom of the Full Duplex Conﬁguration Screen):

•

[1-12]

(for the ﬁrst 12 ports)

•

[13-24]

(for the next 12 ports, if applicable)

•

[25-36]

(for the last 12 ports, if applicable)

2. Press the

Return

key.

Setting One Ethernet Port to Full Duplex

To set one Ethernet port to Full Duplex (for example, port 1):

1. Use the arrow keys to highlight

STANDARD ENET

in the Operation Mode

ﬁeld (to the right of port 1).

2. Press the

Space

Bar

until

FULL DUPLEX

appears in the ﬁeld.

3. Use the arrow keys to highlight the

SAVE

command on the bottom line of the

screen.

4. Press the

Return

key.

Setting All Ethernet Ports to Full Duplex

To set all Ethernet ports to Full Duplex:

1. Use the arrow keys to highlight the

SET ALL PORTS

ﬁeld.

2. Press the

Space

Bar

until you see

FULL

3. Use the arrow keys to highlight the

SAVE

command on the bottom line of the

screen.

4. Press the

Return

key.

9E428-12/36 and 9E429-12/36 Module Speciﬁc Information

Switch Conﬁguration Screen

The 9E428-12/36 and 9E429-12/36 Switch Conﬁguration Screen (Figure 2),

provides basic setup options for making a switch operational in your network.

Figure 2. 9E428-12/36 and 9E429-12/36 Switch Conﬁguration Screen

SmartSwitch 9000 Local Management

Switch Configuration

Module Name: 9E428-36 Firmware Revision: 01.04.07

Slot Number: 9 BOOTPROM Revision: 01.01.01

Switch Address: 00-00-1D-00-08-78 Type of STA: [IEEE]

Numbers of Ports: 37

Port # MAC Address State Status

1 00-00-1D-00-08-78 forwarding [ENABLED]

2 00-00-1D-00-08-79 forwarding [ENABLED]

3 00-00-1D-00-08-7A forwarding [ENABLED]

4 00-00-1D-00-08-7B forwarding [ENABLED]

5 00-00-1D-00-08-7C forwarding [ENABLED]

6 00-00-1D-00-08-7D forwarding [ENABLED]

7 00-00-1D-00-08-7E forwarding [ENABLED]

8 00-00-1D-00-08-7F forwarding [ENABLED]

SAVE [ 9-16 ] EXIT RETURN

Port # refers to the following:

• Port 1 - INB

• Port 2 - Front Panel Port 1

• Port 3 - Front Panel Port 2

• Port 4 - Front Panel Port 3

• Port 5 - Front Panel Port 4

• Port 6 - Front Panel Port 5

• Port 7 - Front Panel Port 6

• Port 8 - Front Panel Port 7

• Port 9 - Front Panel Port 8

• Port 10 - Front Panel Port 9, and so on.

NOTE

9E428-12/36 and 9E429-12/36 Module Speciﬁc Information

Switch Conﬁguration Screen Fields

The following information brieﬂy explains each Switch Conﬁguration Screen

ﬁeld.

Type of STA (Toggle)

Allows you to set the method that switches use to decide which switch is the

controlling (Root) switch when two or more switches exist in parallel (Spanning

Tree Algorithm). Press the Space Bar to toggle to the desired value. Valid types

are:

• DEC

• IEEE

• NONE

Port #

Displays the number of the port for which conﬁguration information is displayed.

MAC Address

Lists the hardware address of each listed switch interface.

State

Displays the current state of each listed interface. The possible interface states

include:

Disabling: Management has disabled this interface. No trafﬁc can be received or

forwarded while the interface is disabled.

Learning: The switch is learning this interface’s network addresses. The switch

enters the learning state when the Transparent Database is created

(during start-up or after being deleted), or when the Spanning Tree

Algorithm detects a network topology change.

Listening: The switch is not adding information to the Transparent Database.

The switch is monitoring BPDU trafﬁc while preparing to move from

the learning to the forwarding state.

Forwarding: The switch is on-line and this interface is forwarding trafﬁc.

Blocking: This interface will not forward any trafﬁc through the switch.

All switches in a network must use the same Spanning Tree protocol. The IEEE

protocol has a unique format for its Bridge Protocol Data Units (BPDU). Trying

to mix STA protocols results in an unstable network.

NOTE

This manual suits for next models

Table of contents

Other Cabletron Systems Network Hardware manuals

Cabletron Systems

Cabletron Systems MMAC-M8FNB User manual

Cabletron Systems

Cabletron Systems TRBMIM User manual

Cabletron Systems

Cabletron Systems 9A426-01 User manual

Cabletron Systems

Cabletron Systems SmartSwitch 6000 Programming manual

Cabletron Systems

Cabletron Systems SSIM-T5-04 User manual

Cabletron Systems

Cabletron Systems WPIM-S/T User manual

Cabletron Systems

Cabletron Systems Expansion module DELHE-UA User manual

Cabletron Systems

Cabletron Systems 6H133-37 User manual

Cabletron Systems

Cabletron Systems TRMIM-22 User manual

Cabletron Systems

Cabletron Systems 9E132-15 Technical document

Cabletron Systems

Cabletron Systems 3F00-01 User manual

Cabletron Systems

Cabletron Systems SWPIM-BRI User manual

Cabletron Systems

Cabletron Systems CRBRIM-W/T Installation manual

Cabletron Systems

Cabletron Systems NBR-220 Programming manual

Cabletron Systems

Cabletron Systems Spectrum EMM-E6 Installation and operating instructions

Cabletron Systems

Cabletron Systems HSIM-W87 User manual

Cabletron Systems

Cabletron Systems BRIM-W6 User manual

Cabletron Systems

Cabletron Systems 9C300-1 User manual

Cabletron Systems

Cabletron Systems CRBRIM-W/E User manual

Cabletron Systems

Cabletron Systems MMAC-Plus 9A128-01 Programming manual

Cabletron Systems

Cabletron Systems TRXI-22 Installation and operating instructions

Cabletron Systems

Cabletron Systems 9C300-1 Quick start guide

Cabletron Systems

Cabletron Systems Expansion module 9H532-17 User manual

Cabletron Systems

Cabletron Systems TRMIM-10R User manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide