Bunn ULTRA-2 PAF Quick reference guide

8. Wash components in a mild

solution of dish detergent using

a bristle brush. Rinse and dry

each item thoroughly before

reassembling.

NOTE: Parts must be thoroughly

dry before adding powder to the

hopper.

7. Slip the O-ring off the Whip-

per Chamber Receptacle and

remove the shaft seal.

4. Twist the Whipper Chamber

clockwise and pull it off the

Whipper Chamber Receptacle.

5. Pull the Frother off the Motor

Shaft. Notice the ﬂat keyway on

the shaft and the matching key-

way inside the Frother. It is im-

portant that these two keyways

are lined up when reassembling.

6. Twist Whipper Chamber Re-

ceptacle clockwise and pull it off

the Motor Shaft. Wipe down all

inside surfaces.

USE & CARE INSTRUCTIONS for ULTRA-2 COLD DRINK DISPENSER WITH PAF DISPENSER

NOTICE - This guide is for quick reference only and is not intended to replace the information in the Operation Manual!

DISASSEMBLY & CLEANING

EMPTY ALL PRODUCT FROM THE ULTRA HOPPERS INTO A BUCKET OR CONTAINER BEFORE PROCEEDING!

1. Open the Cabinet Door and

allow the support arms to lock

in place. Door must remain

open during the entire cleaning

procedure.

3. Pull the Mixing Chamber out

of the Whipper Chamber.

BUNN-O-MATIC CORPORATION

POST OFFICE BOX 3227

SPRINGFIELD, ILLINOIS 62708-3227

PHONE: (217) 529-6601 FAX: (217) 529-6644

ULTRA-2 PAF

ULTRA-2 PAFA

(Page 1 of 4, Continued)

2. Place the power switch in

the OFF position. Slide the gate

shut on the powder hopper and

remove the hopper. Wipe the

hopper tray clean of powder

residue.

2. Depress the hopper lock

plunger, lift slightly.

DISASSEMBLY & CLEANING

Turn cooling to OFF selection. Empty all product from the hopper(s). Turn auger to OFF selection.

4.Pull the auger from the cool-

ing drum.

6. CAUTION: Faucet valve is

under spring tension. Spread

one side of the handle ﬁrst, then

the other and disconnect from

hopper.

8. Remove the auger nose bush-

ing from inside the front of the

hopper. NOTE: Do not scratch

this surface when cleaning. Deep

scratches could cause leakage

around the seal.

5. Remove the hopper seal from

the ﬂange on the cooling drum.

3. Pull the hopper assembly

forward and remove.

9. Remove the drip tray and

cover.

7. Carefully slide valve up to

remove spring and faucet seal.

Extra care should be taken when

handling the seal to prevent

damage.

10. Place all parts in a clean sink with mild hot water (120°F) and sanitizer solution. Allow all parts

to soak for at least 5 minutes. Carefully wash all components with a clean wash cloth in the hot

water and sanitizer solution. Use a clean, soft bristle brush as needed for the smaller components

and tight areas. Do not immerse hopper lids. Use a commercial sanitizer that has 100 ppm of

available chlorine with a concentration level of at least 3% available chlorine (KAY-5 Sanitizer).

Follow the sanitizer’s mixing instructions to ensure 100 ppm of available chlorine.

11. Wash the drum(s), hopper drip tray(s), top cover(s), and outer enclosure using a clean wash

cloth that has been dampened in the hot water and sanitizer solution. Pay particular attention

to the shaft area and make sure it is thoroughly cleaned and sanitized.

12. Thoroughly rinse all surfaces with a clean wash cloth that has been dampened with hot water.

Wipe dry with a clean dry wash cloth before reassembling the dispenser.

NOTE – Although most parts are dishwasher safe, they may be affected by the chemicals in some

commercial sanitizing agents. Do not place the hopper nor hopper lids in a dishwasher. Rinse thor-

oughly before assembly.

1. Slide PAF assembly back

until it latches before removing

ULTRA Hoppers.

43553 071410

ASSEMBLY

2. Install the hopper seal over the

ﬂange at the rear of the cooling

drum as shown.

3. Align the auger shafts with the

augers. Push the augers as far as

they will go and rotate them so

the ﬂat face of the auger shaft is

aligned with the ﬂat face of the

auger nose.

5. Position the faucet seal and

the return spring in the faucet

valve.

6. Slide the faucet valve assem-

bly into place on the hopper.

7. Press down on the valve to

compress the spring. Position

the faucet handle over the faucet

valve one side at a time and snap

into place on the hopper.

9. Turn ON augers and cooling

function to desired settings.

4. Install the hopper over the

auger and cooling drum and

slide it into place. Push down

until the hopper lock plunger

snaps into place.

1. Replace the auger nose bush-

ing inside the front of the hopper.

8. Install the drip tray and cover.

NOTE: Whether liquid concen-

trate or granulated powder, all

product must be thoroughly

mixed BEFORE adding it to the

hoppers.

10. Slide PAF assembly forward. 11. Reassemble and install all

PAF parts. Return power switch

to the ON position. Close Door.

43553 071410

1. Open the Cabinet Door and

allow the support arms to lock

in place.

THOROUGH CLEANING OF THE PAF HOPPER (Once a week)

2. Slide the gate shut on the

powder hopper and remove the

hopper. Remove the Cover and

empty the contents.

3. Pull the Ejector Elbow off the

Hopper Base. Remove the Slide

Gate from the Ejector Elbow.

4. Remove the Wiper Blade and

Drive Gear by removing the

Retaining Ring from the Wiper

Blade Shaft. Remove Auger by

pulling it out the front of Hop-

per Base.

5. Remove the Auger Drive Shaft

by turning the screw of the Au-

ger Drive Bracket in a clockwise

direction.

6. Wash all components in a mild

solution of dish detergent using

a bristle brush when needed.

Rinse and dry each item thor-

oughly before reassembling.

NOTE: Parts must be thoroughly

dry before adding powder to the

hopper.

43553 071410

Other manuals for ULTRA-2 PAF

This manual suits for next models

Popular Beverage Dispenser manuals by other brands

PEGAS

PEGAS Evolution operating instructions

Ugolini

Ugolini MT micro Operator's manual

Gekkeikan

Gekkeikan Sake Machine owner's manual

Olympia

Olympia DH709 Instructions for use

Marco

Marco ECOSMART PB10 instructions

Marvel

Marvel ML24BN Series Installation, operation and maintenance instructions

Cecilware

Cecilware 2K-GB-LD Catalog

Sure Vend

Sure Vend 673 Setup guide

Cornelius

Cornelius 2 Flavor Post-Mix Cold Coffee Dispenser Quest... Technical specifications

Nostalgia Electrics

Nostalgia Electrics KEG7000SS instruction manual

Servend

Servend SV-200 manual 

EdgeStar

EdgeStar VBR440 owner's manual

Cornelius

Cornelius A.B.S. Unit Operator's manual

CDS AUTOMATEN

CDS AUTOMATEN ML-16C2-C user manual

Siemens

Siemens GA 3000 OPERATING & SERVICE MANUAL

Cornelius

Cornelius FCB V4 Operator instructions

Selbach

Selbach Fruit Juice dispenser operating manual

Taylor

Taylor C302NP Operator's manual