Bunn ThermoFresh 44050.0250 Quick reference guide

USE & CARE INSTRUCTIONS for ThermoFresh®SERVER

with DIGITAL SIGHT GAUGE

STEP 2

Place a cup or container in

center of serving platform

as indicated.

STEP 3

Open the faucet handle

until the desired quantity is

dispensed.

STEP 1

The server must be placed

on a sturdy counter or

shelf.

NOTE: Bunn-O-Matic recommends the three step method for cleaning and sanitizing the server. The 3 step method consists

of hot soapy water using an mild, non-citrus detergent, a fresh water rinse and an aqueous sanitizing solution using a non-

chlorine sanitizer. Do not submerge the server. Failure to follow the recommended cleaning procedures can cause

corrosion to the stainless steel surface and damage the vacuum seal. USE OF ANY CHLORINATED PRODUCT VOIDS THE

FACTORY WARRANTY.

Do not submerge server.

39483.0007A09/16 ©2014 Bunn-O-Matic Corporation

BEVERAGE DISPENSING

STEP 3

Rinse server thoroughly

using fresh water rinse.

STEP 2

Flip the lid, fill server with

cleaning solution and

thoroughly clean the inside

of server.

STEP 1

Run a complete brew cycle

of hot water into the server

and let it set for a minute.

Empty the server

completely by opening the

faucet.

STEP 4

Fully fill server with

sanitizing solution for 5

minutes and then drain

through fully open faucet.

DAILY CLEANING

RELEASED FOR PRODUCTION

DIR Num: 39483.0007 22, January 2019

USE & CARE INSTRUCTIONS for ThermoFresh®SERVER

with DIGITAL SIGHT GAUGE

STEP 6

STEP 9

STEP 8

STEP 5

Remove the faucet handle/

stem assembly by unscrew-

ing the faucet nut.

Disassemble the faucet/

stem assembly. Thoroughly

wash all faucet parts, drip

tray and cover in a mild

detergent and water solu-

tion. Rinse the parts in hot

water. Sanitize the parts for

ﬁve minutes, then air dry

completely.

DAILY CLEANING (Continued)

Use cleaning brush supplied

with theserver to thoroughly

clean the ﬁll tube of the lid

assembly and the faucet

spout.

Remove the drip tray and

drip tray cover. Thoroughly

wash in a mild detergent

and water solution. Rinse

the parts in hot water.

STEP 7

Wash the entire outside

surface of the lid assembly

with a mild detergent,

water solution, and a soft,

non-abrasive cloth and

rinse with hot water. Do

not submerge.

NOTE: Thoroughly cleaning

the lid assembly fin will

prevent inaccurate level

readings.

STEP 11

Wash the entire outside

surface of the server with

a soft, non-abrasive cloth.

Do NOT clean with a water

jet device.

STEP 10

Reassemble the faucet and

attach it to the dispenser.

CAUTION: When

reassembling, DO NOT

over-tighten faucet

bonnet. Hand tighten only.

RELEASED FOR PRODUCTION

DIR Num: 39483.0007 22, January 2019

This manual suits for next models

7

Other Bunn Beverage Dispenser manuals

Popular Beverage Dispenser manuals by other brands

PEGAS

PEGAS Evolution operating instructions

Ugolini

Ugolini MT micro Operator's manual

Gekkeikan

Gekkeikan Sake Machine owner's manual

Olympia

Olympia DH709 Instructions for use

Marco

Marco ECOSMART PB10 instructions

Marvel

Marvel ML24BN Series Installation, operation and maintenance instructions

Cecilware

Cecilware 2K-GB-LD Catalog

Sure Vend

Sure Vend 673 Setup guide

Cornelius

Cornelius 2 Flavor Post-Mix Cold Coffee Dispenser Quest... Technical specifications

Nostalgia Electrics

Nostalgia Electrics KEG7000SS instruction manual

Servend

Servend SV-200 manual 

EdgeStar

EdgeStar VBR440 owner's manual

Cornelius

Cornelius A.B.S. Unit Operator's manual

CDS AUTOMATEN

CDS AUTOMATEN ML-16C2-C user manual

Siemens

Siemens GA 3000 OPERATING & SERVICE MANUAL

Cornelius

Cornelius FCB V4 Operator instructions

Selbach

Selbach Fruit Juice dispenser operating manual

Taylor

Taylor C302NP Operator's manual