Brightwell Brightlogic 2 User manual

Brightlogic 2

Quickstart Guide

Installation and Setup

Brightwell.co.uk

Revision 1.0

05/2022

B1051EN

Revision 1.0

05/2022

B1051EN

CONTENTS

SAFETY PRECAUTIONS---------------------------------------------------------------------------------------------------------------------------------------------------- 3

INSTALLATION - MOUNTING --------------------------------------------------------------------------------------------------------------------------------------------- 4

INSTALLATION - WIRING 1------------------------------------------------------------------------------------------------------------------------------------------------- 5

INSTALLATION - WIRING 2------------------------------------------------------------------------------------------------------------------------------------------------- 6

PROGRAMMING - CONTROLS ------------------------------------------------------------------------------------------------------------------------------------------ 7

PROGRAMMING - KEY TO INSTRUCTIONS ---------------------------------------------------------------------------------------------------------------------- 7

PROGRAMMING - LANGUAGE SELECTION---------------------------------------------------------------------------------------------------------------------- 8

FLOW DIAGRAM - INSTRUCTIONS ----------------------------------------------------------------------------------------------------------------------------------- 9

FLOW DIAGRAM - INSTRUCTIONS ----------------------------------------------------------------------------------------------------------------------------------10

FORMULA SELECT-----------------------------------------------------------------------------------------------------------------------------------------------------------11

FORMULA SELECT - INSTALLATION --------------------------------------------------------------------------------------------------------------------------------11

Revision 1.0

05/2022

B1051EN

SAFETY PRECAUTIONS

Important Safety Instructions

Please read the following precautions carefully before using this equipment.

This unit contains high voltage components which, may expose you to the risk of electric shock.

Do not open the enclosure without isolating the signal and supply sources. Ensure that these sources have

been isolated for at least 5 minutes before entering the enclosure.

Means for disconnection must be incorporated in accordance with the wiring rules.

Do not mount the unit to unstable, irregular or non-vertical surfaces.

Do not place heavy objects on top of the unit.

Do not attempt to place items (such as screwdrivers) into the moving parts of the pumphead.

Do not power the unit outside of the values stated on the rating label.

Do not use damaged or frayed cables.

Do not dismantle or modify this equipment.

Do not allow the appliance to be used by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.

Do not allow children being supervised to play with the appliance.

Do not use appliance if the supply cord is damaged. This must be replaced by the manufacturer, its service agent or

similarly qualied persons in order to avoid a hazard.

Always ensure that care is taken when handling chemicals.

Revision 1.0

05/2022

B1051EN

INSTALLATION - MOUNTING

350 mm

13.8 in.

350 mm

13.8 in.

60 mm

2.4 in.

60 mm

2.4 in.

MAXIMUM

2 Metres

Fix the unit to a vertical wall using the screws provided.

Ensure that the unit is level and positioned no more than 2 metres above the base of the product,

which is to be dispensed.

Important notes.

Maximum recommended suction and delivery tubes - 2 metres

Minimum tube size - 8x11mm

Screw pitch/Drilling diagram - on next page

Installation minimum clearance

distances are:

Side: 60 mm (2.4 in.)

Bottom: 350 mm (13.8 in.)

Rear: 0 mm (0 in.)

Revision 1.0

05/2022

B1051EN

INSTALLATION - WIRING 1

In most cases, the interface board or solenoids in the host machine will have a common (i.e their

negative terminals are all linked by a common wire).

The switches S1 & S2 can be left switched to common (up position), and the single(common) wire

taken to the B rail.

Note:

If a signal is applied to Input 2 before Input 1 then the unit will assume that a Pre-wash is not

occurring and will ignore subsequent signals to input 1 until the unit has reset.

RAIL

COMMON

ISOLATED

COMMON

RAIL

LK10-LK19

Switch to common signals

on the B-rail

RP1, RP2, RP3 & RP4

Remove to allow signals below

90 volts AC or DC (min 12V)

Loremipsum

B Rail

(Negative)

With the switches in an

upright position, a

common (neutral/nega-

tive) input signal can be

taken to the B Rail.

A Rail

(Positive)

The positive (live) signal

from each input must be

taken to the relevant

connection on the A Rail.

Seperate connections

are provided on input 2

for Hot & Cold wash

signals.

Example

Recommmended Wiring

Max Size = 1.5mm²

Max Size = 0.5mm²

Current = 0.5A

Safety Warning

If low voltage signals are used, signal wires to the A

and B rails should be routed in separate cable from the

main power to the unit.

Suitable grade wire must be used.

INPUT 1 - Pre-Wash

INPUT 2 - Main Wash

INPUT 3 - Rinse

COMMON

Power Supply

100-240v(AC) 50/60Hz

Sourced from a point which

is isolated when the host

machine is off

Signal Inputs 90v-240v AC or DC

AFS

E - 4

S1 & S2

ISOLATED ISOLATED

Revision 1.0

05/2022

B1051EN

In some cases, the interface board or solenoids in the hose machine are not common. For

example: The softener solenoid on some machines is not linked via a common wire to the other

solenoids.

If this is the case, the signal must be isolated from the common B rail on the Board. This is done

by Switching the appropriate switch (S1 & S2 to isolated, ie. Downward position). If in doubt switch

the appropriate switch for each incoming signal source.

FAILURE TO SWITCH THE APPROPRIATE SWITCH WOULD RESULT IN UNIT FAILURE.

DO NOT ATTEMPT TO SWITCH THE SWITCHES WHEN THE POWER IS ON.

Note:

If a signal is applied to input 2 before input 1 then the unit will assume that a Pre-wash is not

occurring and will ignore subsequent signals to Input 1 until the unit has reset.

RAIL

COMMON

ISOLATED

COMMON

RAIL

B Rail

(Negative)

With the switches in an

upright position, a

common (neutral/nega-

tive) input signal can be

taken to the B Rail.

Separate connections

are provided on input 2

for Hot & Cold wash

signals

A Rail

(Positive)

The positive (live)

signal from each input

must be taken to the

relevant

connection on the A

Rail.

Seperate connections

are provided on input 2

for Hot & Cold wash

signals.

Signal Inputs 90v-240v AC or DC

Example

Recommmended Wiring

Max Size = 1.5mm²

Max Size = 0.5mm²

Current = 0.5A

Safety Warning

If low voltage signals are used, signal wires to the A

and B rails should be routed in separate cable from the

main power to the unit.

Suitable grade wire must be used.

INPUT 1 - Pre-Wash

INPUT 2 - Main Wash

INPUT 3 - Rinse

Power Supply

100-240v(AC) 50/60Hz

Sourced from a point which

is isolated when the host

machine is off

LK10-LK19

Switch to common signals

on the B-rail

RP1, RP2, RP3 & RP4

Remove to allow signals below 90 volts AC or DC (min 12V)

AFS

E - 5

INSTALLATION - WIRING 2

S1 & S2

COMMON

ISOLATED ISOLATED

L N

Revision 1.0

05/2022

B1051EN

PROGRAMMING - CONTROLS

Throughout the instructions:

If a button or buttons are

shown in BLUE then

they must be pressed to

progress to the next stage.

(If two buttons are shown,

they must be pressed

together)

PROGRAMMING - KEY TO INSTRUCTIONS

If buttons are shown in

GREY, they are used

individually to achieve the

desired result. (ie. Either/or)

SIGNAL

ACCEPTANCE TIME

00 SECONDS

MAN 1: ------------------

MAN 2: ------------------

MAN 3: ------------------

OFF P: -------------------

FLUSH VALVE

TIME

00 MINS 00 SECS

Throughout the instructions,

there are several screens

which are highlighted

BOLD.

From any point within the

program, the user can

transition to the next BOLD

screen via the SEE/JUMP

button.

Revision 1.0

05/2022

B1051EN

PROGRAMMING - LANGUAGE SELECTION

French, German, Spanish, Dutch, Czech, Polish, American, Italian or Portuguese.

From the default screen, press and hold the TEST key for 2 seconds. The access code screen

will then be displayed. Enter the correct four-digit access code using the UP and DOWN keys to

select a number and the FWD/ACCEPT key to move (see page 15).

Use the UP and DOWN keys to scroll through the language options. Press the FWD/ACCEPT key

to select the displayed

00000 L10 01

BRIGHTWELL

ENTER CODE TO

CHANGE LANGUAGE

----

ENTER CODE TO

CHANGE LANGUAGE

1---

ENTER CODE TO

CHANGE LANGUAGE

1111

ENGLISH FRANCAIS

POLISHPORTUGUESE ITALIAN

AMERICAN CZECH ESPANOL

DEUTSCH NEDERLAND

Revision 1.0

05/2022

B1051EN

FLOW DIAGRAM - INSTRUCTIONS

ACCESSING MODES

ENTER CODE TO

CHANGE UNIT MODE

----

SELECT

UNIT MODE

STANDARD MODE

SELECT

UNIT MODE

STANDARD MODE

SELECT

UNIT MODE

LEVELS MODE

0000 L1 01

RELAY MODE

Brightwell

SETTINGS

ENTER CODE TO

EDIT SETTINGS

----

STANDARD MODE

Brightwell

(BT = 01)

S/W VERSION 2.08

S/N: 010100001

SIGNAL

ACCEPTANCE

TIME

01 SECONDS

SETTINGS

MAN1: ------------------

MAN 2: ------------------

MAN 3: ------------------

OFF: 1 2 3 4 5 6 7 8 9 0

FLUSH VALVE

TIME

00 MINS 00 SECS

SAFETY STOP MODE

FLOW SWITCH

NO WATER

ACCEPTANCE TIME

05 SECONDS

SET PUMP 1

SPEED

100%

SET PUMP 1

FLOWRATE 00000ML

01/01/2015

SET PUMP 1

SPEED 60S

100%

SAVE SETTINGS

MAN1: 1-----------------

MAN 2: ------------------

MAN 3: ------------------

OFF: 1 2 3 4 5 6 7 8 9 0

STANDARD MODE

00:10 01/01/2015

DATE & TIME

TIME

SETTINGS

TIME

HH:MM:SS

00:00:00

DATE

DD:MM:YY

01:01:01

WIRELESS USB

SETTINGS

BLUETOOTH RF

CHANNEL

CYCLE COUNTERS

TOTAL CYCLES

PROGRAM 01

0000

TOTAL FLOW QTY

PROGRAM 01

00 MINS 00 SECS

TOTAL FLOW QTY

PROGRAM 01

000000ML

TOTAL FLOW QTY

PROGRAM 01

00 MINS 00 SECS

LOW LEVEL

OUTPUT

LOW LEVEL OUTPUT

PULSE

SAVE SETTINGS

LOW LEVEL OUTPUT

CONTINUOUS

FLUSH VALVE MODE

DURING & AFTER

FLUSH VALVE MODE

DURING & AFTER

TOTAL CYCLES

PROGRAM 02

00000

LEVELS MODE

STANDARD MODE

RELAIS MODE

Revision 1.0

05/2022

B1051EN

FLOW DIAGRAM - INSTRUCTIONS

STANDARD MODE

Program

PROGRAM 01

SET INPUT 01

Program

PROGRAM 01

SET INPUT 02

PROGRAM 01

SET INPUT 01

PULSE COUNT

001

PROGRAM 01

SET INPUT 01

SET PUMP 01

DISABLE

PROGRAM 01

SET INPUT 01

SET PUMP 02

DISABLE

INPUT 01 PUMP 01

SET DELAY TIME

00 MIN 00 SECS

PROGRAM 01

SET INPUT 01

SET PUMP 01

ENABLE

INPUT 01 PUMP 01

SET RUN TIME

00 MIN 00 SECS

PROGRAM 01

SET INPUT 02

LEVELS MODE

MASTER

LOAD COUNT

PUMP

PROGRAM

PROGRAM 01

LOAD COUNT

PUMP

PROGRAM 01

PUMP 1, LEVEL 1

SET DELAY TIME

00 MINS 00 SECS

PROGRAM 01

PUMP 1, LEVEL 1

SET RUN TIME

00 MIN 00 SEC

INPUT 01 PUMP 01

SET DELAY TIME

00 MIN 00 SECS

PROGRAM 01

LOAD COUNT

PUMP

PROGRAM 01

PUMP 1, LEVEL 2

DISABLE

PROGRAM 01

PUMP 2, LEVEL 1

SET RUN TIME

00 MIN 00 SEC

MASTER

LOAD COUNT

PUMP

PROGRAM

STANDARD MODE

SET RESET TO

LAST PUMP

SET RESET DELAY

00 MIN 00 SEC

RESET FORMULA

PROGRAM 01

RESET

FORMULA TO

PROGRAM

SET RESET TO

LAST INPUT

CYCLE TIMEOUT

60 MINS

RESET FORMULA

PROGRAM 00

AUTO FORMULA

SELECT MODULE

BINARY

AUTO FORMULA

SELECT MODULE

TIMED

AUTO FORMULA

SELECT MODULE

TIMED +

SET UP TIME

01 SECONDS

BINARY

AUTO FS SIGNAL

ACCEPTANCE

01 SECONDS

BINARY

AUTO FORMULA

ACCEPTANCE

01 SECONDS

BINARY

AUTO FORMULA

SELECT MODULE

BINARY

AUTO FORMULA

SELECT MODULE

TIMED

AUTO FORMULA

SELECT MODULE

TIMED +

SET UP TIME

01 SECONDS

BINARY

AUTO FS SIGNAL

ACCEPTANCE

01 SECONDS

BINARY

AUTO FORMULA

ACCEPTANCE

01 SECONDS

BINARY

Other manuals for Brightlogic 2

Table of contents

Other Brightwell Dispenser manuals

Brightwell

Brightwell ECOMIX COMPACT User manual

Brightwell

Brightwell Microplus II User manual

Brightwell

Brightwell Quantura 200 User manual

Brightwell

Brightwell ECOSHOT User manual

Brightwell

Brightwell ECOMIX COMPACT 2 User manual

Brightwell

Brightwell Super C User manual

Brightwell

Brightwell ECOMULTI STANDARD 4 User manual

Brightwell

Brightwell ECOMIX User manual

Popular Dispenser manuals by other brands

Silver King

Silver King Majestic SK12MAJ Technical manual and replacement parts list

Franke

Franke F3Dn Twin Service manual

STIEBEL ELTRON

STIEBEL ELTRON UltraHot Plus Operation and installation instructions

DAN DRYER

DAN DRYER 282 installation guide

Essity

Essity Tork 473208 manual

CBS

CBS SD300BU-88 COMPONENT MAINTENANCE MANUAL WITH ILLUSTRATED PARTS LIST

Sealey

Sealey MK77 manual

Fluid Management

Fluid Management Accutinter 1600 End user guide

Franke

Franke DVS SD99-010 Installation and operating instructions

Graco

Graco Dispensit 1053-10C operation & maintenance

ITALTINTO

ITALTINTO i50 user manual

Coca-Cola

Coca-Cola FREESTYLE 9000 user guide

Graco

Graco ProMix 2KE Operation

TECHCON SYSTEMS

TECHCON SYSTEMS TS1251 user manual

Wayne

Wayne GLOBAL VISTA CNG instruction manual

clarsen

clarsen H133 Instructions for use

PicoBrew

PicoBrew Zymatic user manual

BOWMAN

BOWMAN BP-007 manual