Bosch Solution 6+6 Wireless On/Off User manual

Solution 6+6

Quick Reference Guide

ISSUE 1.20

Solution 6+6

Quick Reference Guide

SYDNEY, AUSTRALIA

Document Part Number MA600Q

Document Issue 1.20

Printed 23 May 2006

This documentation is provided to suit Solution 6+6 (CC600/LP600)

Firmware Revision 1.20 - 1.27

Hardware Revision D

Alarm Link Form - Software Version 1.20 - 1.27 = S6_V12

any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior

written permission of Bosch Security Systems Pty Limited.

Trademarks

Throughout this document trademark names may have been used. Rather than put a trademark symbol in every

occurrence of a trademark name, we state that we are using the names only in an editorial fashion and to the

benefit of the trademark owner with no intention of infringement of the trademark.

Notice of Liability

While every precaution has been taken in the preparation of this document, neither Bosch Security Systems Pty

Limited nor any of its official representatives shall have any liability to any person or entity with respect to any

liability, loss or damage caused or alleged to be caused directly or indirectly by the information contained in this

book.

Bosch Security Systems Pty Limited reserves the right to make changes to features and specifications at any

time without prior notification in the interest of ongoing product development and improvement.

Page 2 Solution 6+6 Quick Reference Guide

SOL 6+6 QUICK REF GUIDE.DOC Bosch Security Systems Pty Limited

Introduction

Thank you for choosing the Solution 6+6 control panel for your installation. We are sure that you will find

this system extremely flexible, reliable and easy to use.

Before using the system for the first time, we suggest that you read the section in this Quick Reference Guide

called “Programming Using The Remote Codepad” to familiarise yourself with the basic programming

methodology.

The Quick Reference Guide is supplied with the Solution 6+6 to provide users with enough basic

information to wire, configure and operate the system. Due to the systems many programmable features and

options we suggest that you obtain the complete Installation Manual which provides detailed information on all

system options and functions as well as detailed information on the numerous programming methods.

Programming

The programming options of this system are stored in a non-volatile EPROM. This memory will hold all the

relevant configuration and user specific data even during a total power loss.

The data retention time is as long as ten years without power, therefore no reprogramming will be required after

powering the system down.

The data can be altered as many times as required without the need for any additional specialised equipment.

This memory is laid out in numerous locations, each of which holds the data for a specific function. In general,

the entire programming sequence will consist of nominating the location then entering or altering the required

data. You will repeat this procedure until all the data has been altered to suit your requirements. The factory

default settings have been selected for Contact ID format.

Note: '15' is the maximum value that can be programmed into any location.

There are two programming modes. The Installer’s Programming Mode and the Operators Programming Mode.

Both modes have individual access codes and these two codes must always be programmed differently. The

Master Code, as well as being able to arm and disarm the system gives access to the Operators Programming

Mode. The Installer’s Code only gives access to the Installer’s Programming Mode and does NOT arm and

disarm the system.

Programming of the Solution 6+6 control panel can be carried out via any of the following four methods.

System Codepad

Hand Held Programmer (CC814)

Programming Key (CC810)

Alarm Link (Upload/Download) Software (CC816)

Note: For further information on the different programming options available for the Solution 6+6,

refer to the Installation Manual (MA600I).

Solution 6+6 Quick Reference Guide Page 3

Bosch Security Systems Pty Limited SOL 6+6 QUICK REF GUIDE.DOC

Programming Using The Remote Codepad

The system must be in the disarmed state with no flashing zone alarm memories, this can be achieved by

entering the followed by the button. The factory default Master Code is 2580.

To access the Installer’s Programming Mode, enter the four digit followed by the button.

The factory default Installer Code is 1234. Three beeps will be heard and both the AWAY and the STAY

indicators will flash simultaneously. If a long beep is heard, check the system for alarm memory. The codepad

indicators will display the current data stored in the first location (LOCATION 000).

Table 1: Zone Indicators When Programming

Example

To enter Installer’s Programming Mode, enter the followed by the button. Three beeps

will be heard and the codepad will display the current data stored in “LOCATION 000”.

To move to a particular programming location, enter the required followed by the

button. The data of the new location will now be displayed.

To move to the next location, press the button. This will step you to the next location and the data in that

location will be displayed via the ZONE indicators.

If you press the button without previously entering a location number, the system will step back one

location. To change data in the current location, enter the new value (0 – 15) followed by the button.

This will store the new data into the location and still leave you positioned at the same location.

To proceed to the next location, press the button. The next locations data will now be displayed.

To exit the Installer’s Programming Mode, enter command 960 followed by the button. Two beeps

will be heard and the system will return to the disarmed state.

For a more detailed explanation, refer to the Solution 6+6 Installation Manual

(MA600I).

Data

Value Zone 1

Indicator Zone 2

Indicator Zone 3

Indicator Zone 4

Indicator Zone 5

Indicator Zone 6

Indicator Zone 7

Indicator Zone 8

Indicator MAINS

Indicator

1 

2 



8 

9 



11 



12 



Page 4 Solution 6+6 Quick Reference Guide

SOL 6+6 QUICK REF GUIDE.DOC Bosch Security Systems Pty Limited

Quick Start

The following steps will enable you to use the Solution 6+6 panel with the default values as set in the

factory. The default settings allow the panel to communicate in Contact ID format.

1. Connect AC plug pack to the control panel.

2. Check the operation of the red overload LED (LD1) on the PCB. In normal operation the LED will not

illuminate. The MAINS indicator will remain on, as will the AWAY indicator. The unit is now in the

armed state.

3. Enter the default Master Code 2580 followed by the button. The AWAY indicator will

extinguish. The panel is now in the disarmed state. Installer’s Programming Mode can now be accessed.

4. The back-up battery should now be connected.

5. Enter the factory default Installer Code 1234 followed by the button. The STAY and

AWAY indicators will now flash simultaneously.

6. Enter the Primary Telephone Number followed by the Secondary Telephone Numbers and the Subscriber

ID Number.

7. Set the time for the test reports if this option is required. Any other programming changes required can

also be made, otherwise the factory programming default settings will be used.

8. Enter command 960 followed by the button to exit Installer’s Programming Mode. The

control panel will return to the disarmed state and is now ready for use.

9. Use the Master Code to set the date and time.

How To Set The New Date and Time

1. Enter your followed by 6and the button.

Three beeps will be heard and the STAY and AWAY indicators will begin to flash.

2. Enter the day, month, year, hour and minute using the (DD, MM, YY, HH, MM) format.

3. Press the button when finished.

Two beeps will be heard and the STAY and AWAY indicators will extinguish.

Zone Default Settings

The zone default settings are as listed in the table below.

Zone No Zone Type

1 Delay-1

2, 3, 4 & 5 Handover

6 24 Hour

Table 2: Zone Default Settings

Note: The example given in this quick reference guide is a simplified description of how to configure

the panel. This system offers many other programmable features, which are described in detail

in the Solution 6+6 Installation Manual (MA600I).

Solution 6+6 Quick Reference Guide Page 5

Bosch Security Systems Pty Limited SOL 6+6 QUICK REF GUIDE.DOC

Installer’s Programming Commands

There are several commands that can be invoked to perform the functions as listed below. These commands

only operate while you are in the Installer’s Programming Mode. To invoke the command, enter in the

corresponding numerical code then press the button.

Command Description

958 Enable and Disable Zone Status Mode When Using The Hand Held Programmer

959 Test Programming Key

960 Exit Installer’s Programming Mode

961 Reset To Factory Default Settings (Contact ID Format)

962 Copy The Panel Memory To The Programming Key

963 Copy The Programming Key Data To The Panel Memory

964 Wipe Programming Key

965 Set Defaults For Domestic Dialling Reporting Format

966 Enable and Disable Automatic Stepping Of Locations During Programming

999 This Command Displays The Control Panel’s “Software Version” Number When

Using The Hand Held Programmer

Table 3: Installers Programming Commands

Installer Code Functions

Installer Code functions are designed to allow the installer to perform various system tests without the need to

know a Master Code.

The is entered followed by a digit then the button to activate the particular

function.

These functions can only be carried out while the system is in the disarmed state.

Function Description

0 Fault Analysis Mode

1 Reserved

2 Set Number Of Days Until The First Test Report

3 Event Memory Recall

4 Walk Test Mode

5 BOSCHSAT - Satellite Siren Service Mode

6 Initiate Modem Call

7 Turning Telephone Monitor Mode On and Off

8 Reserved

9 Send A Test Report

Table 4: Installer Code Functions

How To Enter Fault Analysis Mode

1. Enter your followed by 0and the button.

One or more zone indicators will illuminate to indicate the type of fault that has occurred.

2. Press the button to exit this function.

How To Set the Number Of Days Until The First Test Report

1. Enter your followed by 2and the button.

2. Enter the (01 – 99) until the first test report followed by the button.

Page 6 Solution 6+6 Quick Reference Guide

SOL 6+6 QUICK REF GUIDE.DOC Bosch Security Systems Pty Limited

How To Enter Event Memory Recall Mode

1. Enter your followed by 3and the button.

The event memory will be played back in reverse chronological order.

2. Press the button to exit this function, or wait until the function automatically terminates after the

last event has been replayed.

How To Enter Walk Test Mode

1. Enter your followed by 4and the button.

The codepad will beep once every second while the system is in the walk test mode.

2. Unseal and seal the zones to be tested.

The codepad will sound one long beep while the horn speaker will sound one short beep every time a

zone is sealed or unsealed.

3. Press the button to exit this function once all zones have been tested.

How To Activate Satellite Service Mode

1. Enter your followed by 5and the button.

The satellite siren will return to the normal operating state when the system has been armed.

How To Initiate A Modem Call

1. Enter your followed by 6and the button.

How To Turn Telephone Monitor Mode ON

1. Enter your followed by 7and the button.

Three beeps will be heard and the codepad will beep once every two seconds whilst this mode is active.

Telephone monitor mode allows the codepad to be used for a visual representation of data transmissions

between the control panel and the base station receiver. The dialling sequence is also shown in this mode.

The codepad will beep once every two seconds while telephone monitor mode is turned on regardless of whether

the system is in Installer’s Programming Mode or normal operating mode. The first five zone indicators are

used to display the progressive steps for a transmission to the base station receiver.

Zone LED Event

1 Telephone Line Seized

2 Dialling Phone Number

3 Handshake Received

4 Data Is Being Transmitted

5 Kiss Off Received

None Telephone Line Released

Table 5: Telephone Monitor Mode Indications

How To Turn Telephone Monitor Mode Off

1. Enter your followed by 7and the button.

Two beeps will be heard and the codepad will cease beeping once every two seconds.

How To Send A Test Report

1. Enter your followed by 9and the button.

Solution 6+6 Quick Reference Guide Page 7

Bosch Security Systems Pty Limited SOL 6+6 QUICK REF GUIDE.DOC

Master Code Functions

Master Code functions are designed to allow those users that have the appropriate access level to perform certain

functions of a supervisory level. These functions can only be carried out while the system is in the disarmed

state.

The is entered followed by a digit then the button to activate the particular

function.

Function Description

0 Arming or Disarming Both Areas At The Same Time (Partitioning Only)

1 Changing and Deleting User Codes

2 Changing Domestic Phone Numbers

3 Event Memory Recall

4 Walk Test Mode

5 Fault Analysis Mode

6 Setting The Date and Time

7 Turning Day Alarm On/Off

8 Reset Latched Outputs

9 Initiate Modem Call

Table 6: Master Code Functions

How To Arm Or Disarm Both Areas At The Same Time

1. Enter your followed by 0and the button.

Both areas will arm or disarm to follow the state of the area that the code was entered from.

How To Add Or Change A User Code

1. Enter your followed by 1and the button.

2. Enter the that you wish to add or change followed by the button.

3. Enter all the digits for the followed by the button.

How To Delete A User Code

1. Enter your followed by 1and the button.

2. Enter the that you wish to delete followed by the button.

3. Press the button to delete the user code.

How To Change Domestic Phone Numbers

1. Enter your followed by 2and the button.

2. Enter all the digits for , one digit at a time. You will notice as each digit is entered, the

corresponding number on the codepad will illuminate.

3. After all the digits for the first telephone number have been entered, press the button to separate

the first telephone number and the second telephone number. If there is only one phone number, press

the button to exit this function.

4. Enter all the digits for , one digit at a time. You will notice as each digit is entered, the

corresponding number on the codepad will illuminate.

5. After the last digit of the second telephone number has been entered, press the button to separate

the second telephone number and the third telephone number, otherwise, press the button to exit

this function.

Page 8 Solution 6+6 Quick Reference Guide

SOL 6+6 QUICK REF GUIDE.DOC Bosch Security Systems Pty Limited

How To Enter Event Memory Recall Mode

1. Enter your followed by 3and the button.

The event memory will be played back in reverse chronological order.

2. Press the button to exit this function, or wait until the function automatically terminates after the

last event has been replayed.

How To Enter Walk Test Mode

1. Enter your followed by 4and the button.

The codepad will beep once every second while the system is in the walk test mode.

2. Unseal and seal the zones to be tested.

The codepad will sound one long beep while the horn speaker will sound one short beep every time a

zone is sealed or unsealed.

3. Press the button to exit this function once all zones have been tested.

How To Enter Fault Analysis Mode

1. Enter your followed by 5and the button.

One or more zone indicators will illuminate to indicate the type of fault that has occurred.

2. Press the button to exit this function.

How To Set The Date and Time

1. Enter your followed by 6and the button.

2. Enter the day, month, year, hour and minute using the format (DDMMYYHHMM) followed by the

button.

How To Turn Day Alarm On and Off

1. Enter your followed by 7and the button.

Three beeps indicate that day alarm is turned on, two beeps indicate that day alarm is turned off.

How To Reset Latching Outputs

1. Enter your followed by 8and the button.

How To Initiate A Modem Call

1. Enter your followed by 9and the button.

Solution 6+6 Quick Reference Guide Page 9

Bosch Security Systems Pty Limited SOL 6+6 QUICK REF GUIDE.DOC

User Code Functions

Function Description

0 Arming or Disarming Both Areas At The Same Time (Partitioning Only)

Table 7: User Code Functions

Fault Analysis Mode

There are various system faults that can be detected by the control panel. When any of these are present the

FAULT indicator will begin to flash and the codepad will beep once every minute. Hold the 5button down for

two seconds until two beeps are heard. The STAY and AWAY indicators will begin to flash in unison with the

FAULT indicator. One or more zone indicators (1-8) will illuminate to indicate the current fault(s). Refer to the

following table below.

Zone

Indicator

Description

1 Low Battery

2 Date and Time

3 Sensor Watch

4 Horn Speaker Disconnected

5 Reserved

6 E2Fault

7 Reserved

8 Communications Failure

Table 8: Fault Types

Hold Down Functions

Hold down functions have been incorporated to allow easy activation of specific operations. When a button is

held down for two seconds, two beeps will be heard and a particular function will operate. The hold down

functions are listed below.

Function Description

AWAY Arm The System In AWAY Mode

STAY Arm The System In STAY Mode

0 Reserved

1 Horn Speaker Test

2 Bell Test

3 Strobe Test

4 Turning Day Alarm On and Off

5 Fault Analysis Mode

6 Initiate Modem Call

7 Reset Latching Outputs

8 Codepad ID Beeper Tone Change

9 Initiate Test Report

Table 9: Hold Down Functions

Page 10 Solution 6+6 Quick Reference Guide

SOL 6+6 QUICK REF GUIDE.DOC Bosch Security Systems Pty Limited

Other manuals for Solution 6+6 Wireless On/Off

Table of contents

Other Bosch Control Panel manuals

Bosch

Bosch Radionics D8024 Manual

Bosch

Bosch Rexroth IndraControl VCP 20 Technical manual

Bosch

Bosch ICP-EZM2 User manual

Bosch

Bosch DS3MX-E-U User manual

Bosch

Bosch BE 300 LSN User manual

Bosch

Bosch Easy Series User manual

Bosch

Bosch Radionics D8024 Quick start guide

Bosch

Bosch Solution 6+6 Wireless On/Off User manual

Bosch

Bosch DS7200V2-UK Assembly instructions

Bosch

Bosch D7212GV2 How to use

Bosch

Bosch D9112B Troubleshooting guide

Bosch

Bosch DS3MX-E-U User manual

Bosch

Bosch Solution Ultima 880 User manual

Bosch

Bosch 2000 Series Troubleshooting guide

Bosch

Bosch MPC-xxxx-C Series User manual

Bosch

Bosch Rexroth IndraControl VDP 92.3 Technical manual

Bosch

Bosch HPC 400 User manual

Bosch

Bosch Solution 6+6 Wireless AE User manual

Bosch

Bosch B6512 User manual

Bosch

Bosch Rexroth IndraControl VAM 11.1 Technical manual

Bosch

Bosch D9412GV4 Operating instructions

Bosch

Bosch B9512G User manual

Bosch

Bosch MPC-xxxx-C Series User manual

Bosch

Bosch ICP-CC408 User manual

Popular Control Panel manuals by other brands

RDZ

RDZ PC-HRX user manual

STG-BEIKIRCH

STG-BEIKIRCH MZ3 operation instruction

Efka

Efka Variocontrol V810 instruction manual

Cebora

Cebora 208-10 instruction manual

AMX

AMX AutoPatch CP-15 instruction manual

Satel

Satel CA-6 KLED-S user manual

Evolution

Evolution IQ plus 800 installation manual

Fagor

Fagor 8040 TCO CNC operating manual

Trane

Trane ComfortLink II XL950 Control user guide

AKO

AKO PROCool AKO-17635-2 quick guide

ABB

ABB 6136/30M-101 operating instructions

Telikou

Telikou BK-603 Belt Pack instruction manual

Mapei

Mapei Mapeheat Thermo Touch user guide

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 user manual

Sminn

Sminn BOX L VF1L EI instruction manual

Balboa

Balboa TP600 user manual

Nice

Nice HSCU1 Instructions and warnings for installation and use

Truma

Truma CP plus installation instructions