Bosch D9412GV3 User manual

Control Panels

D9412GV3/D7412GV3/D7212GV3

en UL Installation Instructions

Control Panels Table of Contents | en 3

Bosch Security Systems, Inc. UL Installation Instructions F.01U.167.105 | 02 | 2010.11

Table of Contents

1 Installation 4

1.1 Installation Preparation 4

1.2 Enclosure Options 4

1.3 Mounting Enclosure 4

1.4 Installing the Control Panel 5

1.5 Connecting Earth Ground 5

1.5.1 Terminal 10 5

1.5.2 Ground Fault Detect Enable 6

1.5.3 Enabling Ground Fault Detection 6

1.5.4 GV3 Series Ground Fault Specifications 7

1.5.5 Locking the Reset Pin 7

2Diagrams 8

2.1 Faceplates 8

2.2 Power Supply Side Wiring Diagrams 9

2.2.1 D9412GV3/D7412GV3 Power Supply Side Wiring Diagram (D9412GV3 shown) 9

2.2.2 D7212GV3 Power Supply Side Wiring Diagram 10

2.3 Input Points and Peripheral Devices Wiring Diagram (D9412GV3 shown) 11

2.4 SDI Devices Wiring Diagrams 12

2.4.1 D9412GV3 SDI Devices Wiring Diagram 12

2.4.2 D7412GV3 SDI Devices Wiring Diagram 13

2.4.3 D7212GV3 SDI Devices Wiring Diagram 14

2.5 Keyswitch Wiring 15

3 Power Supply and Power Outputs 16

3.1 Power Supply - Primary 16

3.1.1 Primary (AC) Power Circuit 16

3.1.2 Installing the Transformer 16

3.2 Power Terminals - Secondary 17

3.2.1 Secondary (DC) Power 17

3.2.2 Installing the Battery 17

3.3 Power Outputs - Circuit Protection 19

3.4 Power Outputs - Total Available Power 19

3.5 Power Outputs - Continuous Power Output Terminals 3, 8, 24, and 32 20

3.6 Power Outputs - Programmable Power Output Terminals 6, 7, and 8 20

3.6.1 Programming 20

3.6.2 Terminals 6 and 7 20

3.6.3 Fire System Power Formula 21

3.6.4 Terminal 8 21

4 Specifications 22

4.1 Terminal Wiring Requirements 23

4.2 Compatible Accessories 25

4.3 Circuit Classes 26

4en | Installation Control Panels

F.01U.167.105 | 02 | 2010.11 UL Installation Instructions Bosch Security Systems, Inc.

1 Installation

1.1 Installation Preparation

This section contains a general installation procedure and refers to other sections of the

document for detailed instructions. Review this document and the D9412GV3/D7412GV3

Program Entry Guide (P/N: F01U170807) or D7212GV3 Program Entry Guide

(P/N: F01U170808) before beginning the installation to determine the hardware and wiring

requirements for the features used. Have the following documentation available when reading

through this guide:

–D9412GV3/D7412GV3 Program Record Sheet (P/N: F01U170809) or D7212GV3 Program

Record Sheet (P/N: F01U170810)

–Security System Owner's Manual (P/N: 71-06633-000) and GV3 Series Owner's Manual

Supplement (P/N: F01U143082)

– Installation manual for keypad or annunciator (D1255 all models, D1255RB, D1256,

D1256RB, D1257, D1257RB, or D1260 all models)

1.2 Enclosure Options

Mount the control panel assembly in any of the Bosch Security Systems, Inc. enclosures

listed:

– D8103 Universal Enclosure (tan)

– D8109 Fire Enclosure (red) for the D9412GV3 and D7412GV3 Control Panels

– D8108A Attack Resistant Enclosure (tan)

Refer to the D9412GV3/D7412GV3 Approved Applications Compliance Guide

(P/N: F01U143069) or D7212GV3 Approved Applications Compliance Guide (P/N: F01U143080)

to determine if the application requires a specific enclosure.

1.3 Mounting Enclosure

1. Run the necessary wiring throughout the premises.

2. Mount the enclosure in the desired location. Use all five enclosure mounting holes. Refer

to Figure 1.1, Page 5.

3. Pull the wires into the enclosure.

NOTICE!

Electromagnetic interference (EMI) can cause problems on long wire runs.

Control Panels Installation | en 5

Bosch Security Systems, Inc. UL Installation Instructions F.01U.167.105 | 02 | 2010.11

Figure 1.1 Enclosure Mounting

1.4 Installing the Control Panel

1. Place the control panel over the inside back of the enclosure, aligning the large

rectangular openings of the mounting skirt with the mounting hooks of the enclosure.

Slide the control panel down so that it hangs on the hooks. Refer to Figure 1.1, Page 5.

2. Remove the tape from the #6 x 1/4-in. screw in the mounting tab on the control panel.

The screw passes through the mounting tab and into the skirt mounting hole in the

enclosure. Tighten the screw to secure the control panel in the enclosure.

3. Connect earth ground to the control panel before making any other connections. Refer to

Section 1.5 Connecting Earth Ground, page 5.

1.5 Connecting Earth Ground

1.5.1 Terminal 10

To help prevent damage from electrostatic charges or other transient electrical surges,

connect the system to earth ground at Terminal 10 before making other connections.

Recommended earth ground references are a grounding rod or a cold water pipe.

Callout Description

1 Point chart label

2 Mounting skirt hooks (2)

3 Module mounting holes (12)

4 Tamper switch mounting holes (5)

5 Skirt mounting hole (1)

6 Enclosure mounting holes (5)

7 Mounting skirt hook holes (2)

8 Back of the control panel

9 Lock down tab

6en | Installation Control Panels

F.01U.167.105 | 02 | 2010.11 UL Installation Instructions Bosch Security Systems, Inc.

1.5.2 Ground Fault Detect Enable

A ground fault is a circuit impedance to earth ground. The control panel has a ground fault

detection circuit that, when enabled, detects ground faults on Terminals 1 to 9 and 11 to 32.

The control panel also detects and annunciates ground faults on any device connected to it.

If a ground fault condition occurs, the keypads display SERVC GND FAULT and the control

panel sends a GROUND FAULT TROUBLE, AREA 1. When the control panel recognizes that the

ground fault condition is corrected, and remains corrected for between 5 to 45 consecutive

seconds, a Restoral Report is sent.

1.5.3 Enabling Ground Fault Detection

To enable the Ground Fault Detect Enable feature, lock (close) the S4 Ground Fault Detect

Pin on the control panel (refer to Figure 1.2, Page 6).

Figure 1.2 Ground Fault Detect (S4)

WARNING!

Do not use telephone or electrical ground for the earth ground connection. Use 1.8 mm (14

AWG) to 1.5 mm (16 AWG) wire when making the connection. Do not connect other control

panel terminals to earth ground.

NOTICE!

To meet UL 864 requirements, enable Ground Fault Detect.

NOTICE!

The D9412GV3/D7412GV3/D7212GV3 Control Panels log and print a Ground Fault event as a

Trouble Point 256 if communicating in Modem IIIa2format. If communicating in Contact ID

format, the D7212GV3 generates a Ground Fault (310) event.

Callout Description

1 S4 Locked (Closed). Control panels detects ground faults.

2 S4 Unlocked (Open). Control panel does not detect ground faults.

Control Panels Installation | en 7

Bosch Security Systems, Inc. UL Installation Instructions F.01U.167.105 | 02 | 2010.11

1.5.4 GV3 Series Ground Fault Specifications

Table 1.1, Page 7 provides the impedance specifications for detecting ground faults when any

terminal or field wiring is shorted to ground.

Table 1.1 Ground Fault Impedance Specifications

1.5.5 Locking the Reset Pin

Locking the reset pin disables the control panel (refer to Figure 1.3, Page 7). When the control

panel is disabled, the system ignores the keypads and points. CALL FOR SERVICE appears in

keypad displays when the pin is locked down.

On-board relays (Terminals 6 and 7) and off-board relays deactivate when the control panel is

reset. Terminal 8 has power when the relay is deactivated. Activation interrupts power at that

terminal. The on-board relay (Terminal 8) remains deactivated when the reset pin is locked in

the disable position.

Releasing the reset pin from the closed position resets the control panel. The control panel

resets all its timers, counters, indexes, and buffers. Any points that restore after a reset do

not generate Restoral Reports.

If the reset pin is placed in the disable position when all areas are armed, there must be an

entry in the Answer Armed program item. Refer to RPS Parameters in the D9412GV3/

D7412GV3 Program Entry Guide (P/N: F01U170807) or the D7212GV3 Program Entry Guide (P/

N: F01U170808).

Locking the pin in the disable position applies power to the control panel and charges the

battery while the detection devices and keypads are installed.

When the Reset Switch (labeled S1) is closed, the communication module at SDI Address 92

is disabled. While in this mode, remote programming communication is only supported by the

communication module at SDI Address 88.

Figure 1.3 Reset Pin

Impedance Control Panel Detects Ground Fault

≤ 300 ΩYes

300 Ωto 200 k ΩDetection depends upon the terminal

≥ 200 k ΩNo

Callout Description

1 Reset pin locked (closed)

2 Reset pin normal (open)

8en | Diagrams Control Panels

F.01U.167.105 | 02 | 2010.11 UL Installation Instructions Bosch Security Systems, Inc.

2 Diagrams

2.1 Faceplates

Callout Description Callout Description

1 Charging status LED (yellow) 8 Ring

2 Low battery LED (red) 9 S3, Point 8 EOL selection

3 Color-coded battery leads 10 Operation monitor LED (green)

4 Ground fault detect enable 11 Accessory connector

5 Phone LED (red) 12 Programming connector

6 Tip 13 Reset pin

7 Telephone cord connector 14 SDI quick connector

Control Panels Diagrams | en 9

Bosch Security Systems, Inc. UL Installation Instructions F.01U.167.105 | 02 | 2010.11

2.2 Power Supply Side Wiring Diagrams

2.2.1 D9412GV3/D7412GV3 Power Supply Side Wiring Diagram

(D9412GV3 shown)

Callout Description Callout Description

1 If required by local AHJ, connect D113 Battery

Lead Supervision Module.

9 To Relay A or Relay B

2 Batteries 10 Listed Audible Signaling Devices rated at

12.0 VDC nominal (do not use vibrating type

horns)

3 D122 Dual Battery Harness, as required 11 C900V2 (optional)

4 D1640 Transformer and D8004 Transformer

Enclosure required for NFPA Applications

12 RJ31X, secondary phone line

5 D8132 Dual Battery Charger with two batteries

(Batteries are not supervised.)

13 560 Ω, 2 W EOL Resistor (P/N: 15-03130-005)

6 Power limited, supervised 14 RJ31X, primary phone line

7 Power limited 15 D928

8 D192G Bell Supervision Module 16 To earth ground

NOTICE!

All external connections except Terminal 5 (battery positive) are power limited.

10 en | Diagrams Control Panels

F.01U.167.105 | 02 | 2010.11 UL Installation Instructions Bosch Security Systems, Inc.

2.2.2 D7212GV3 Power Supply Side Wiring Diagram

Callout Description Callout Description

1 If required by local AHJ, connect D113

Battery Lead Supervision Module.

8 D192G Bell Supervision Module

2 Batteries 9 To Relay A or Relay B

3 D122 Dual Battery Harness, as required 10 Listed Audible Signaling Devices rated at 12.0

VDC nominal (Do not use vibrating type horns.)

4 D1640 Transformer and D8004 Transformer

Enclosure required for NFPA Applications

11 C900V2 (optional)

5 D8132 Dual Battery Charger with two

batteries (Batteries are not supervised.)

12 560 Ω, 2 W EOL Resistor (P/N: 15-03130-005)

6 Power limited, supervised 13 RJ31X, primary telephone line

7 Power limited 14 To earth ground

NOTICE!

All external connections except Terminal 5 (battery positive) are power limited.

Other manuals for D9412GV3

This manual suits for next models

Table of contents

Other Bosch Control Panel manuals

Popular Control Panel manuals by other brands

RDZ

RDZ PC-HRX user manual

STG-BEIKIRCH

STG-BEIKIRCH MZ3 operation instruction

Efka

Efka Variocontrol V810 instruction manual

Cebora

Cebora 208-10 instruction manual

AMX

AMX AutoPatch CP-15 instruction manual

Satel

Satel CA-6 KLED-S user manual

Evolution

Evolution IQ plus 800 installation manual

Fagor

Fagor 8040 TCO CNC operating manual

Trane

Trane ComfortLink II XL950 Control user guide

AKO

AKO PROCool AKO-17635-2 quick guide

ABB

ABB 6136/30M-101 operating instructions

Telikou

Telikou BK-603 Belt Pack instruction manual

Mapei

Mapei Mapeheat Thermo Touch user guide

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 user manual

Sminn

Sminn BOX L VF1L EI instruction manual

Balboa

Balboa TP600 user manual

Nice

Nice HSCU1 Instructions and warnings for installation and use

Truma

Truma CP plus installation instructions