Bosch ICP-EZM2 User manual
Easy Series Control Panel
ICP-EZM2
en Quick Start Guide
Table of contents
1Install the Enclosure 4
2Wire the Control Panel 6
3Configure the System 8
3.1 Configuring with the telephone 8
3.2 Configuring with RPS 8
4Add/Change Users 10
4.1 Add users 10
4.2 Change users 10
5System Test and Maintenance 11
6Installer Telephone Menu 12
7Appendix 13
7.1 Expert Programming 13
7.2 Country Codes 23
7.3 Default Passcodes 23
Easy Series Control Panel Table of Contents | en 3
Bosch Security Systems, Inc. Quick Start Guide 2014.09 | 01 | F.01U.306.216
Install the Enclosure
Refer to Figure 1.1 for the suggested placement of system components in the enclosure.
Notice!
Use proper anchor and screw sets when installing the enclosure on non-load-bearing
surfaces, such as drywall.
Follow anti-static procedures when handling the control panel board. Touch the earth ground
terminal on the control panel board to discharge any static charge before working on the
control panel board.
If you install more than one control center, mount them at least 1.2 m apart.
Do not install the RADION receiver within 15 cm (6 in) of the control centers metal enclosure.
12 VDC
2
3
4
5
6
1
7
Figure 1.1: System component placement in enclosure
1
4en | Install the Enclosure Easy Series Control Panel
2014.09 | 01 | F.01U.306.216 Quick Start Guide Bosch Security Systems, Inc.
Callout Description
1 Port for ICP-EZPK programming key and ICP-EZRU2-V3
Update Key
2 ICP-EZTS Cover and Wall Tamper Switch
3 Ground connection
Connect ground wire from enclosure to enclosure door.
4 Module mounting location
5 Module mounting location
6 Status LED (√)
System Test Button (→)
7 Port for ICP-EZV2 Voice Module
Easy Series Control Panel Install the Enclosure | en 5
Bosch Security Systems, Inc. Quick Start Guide 2014.09 | 01 | F.01U.306.216
Wire the Control Panel
Refer to Figure 2.1 for an overview of the system components and wiring.
IUI-EZ1
1
B
G
Y
R
RFRC-OPT
2
B
G
Y
R
DX2010
3
B
G
Y
R
+
-
9
(+) (-)
10
7
8
B
G
Y
R
B426 6
B
G
Y
R
B450
4
5
11
12
(+) (-)(+) (-)(+) (-)
(+)
(-)
(+)(+)
(+) (-)
+
(-)
(+)
(-)
Figure 2.1: Wiring diagram
Callout Description
1Control Center Mount within 3 m of control panel, Use
CAT5 cable (twisted pair) for audio
bus, Set data bus address (1 - 4), up to
4 controls max
2RADION receiver
1 = Normal Operation
5 = Maintenance Mode
3DX2010 Point
Expander
Data bus Adr 102: Points 9-16
Data bus Adr 103: Points 17-24
Data Bus Adr 104: Points 25-32
2
6en | Wire the Control Panel Easy Series Control Panel
2014.09 | 01 | F.01U.306.216 Quick Start Guide Bosch Security Systems, Inc.
Callout Description
4B426 Network
Interface Module
Use address 6.
5B450 Conettix
Plug-in
Communicator
Use address 6.
6Supervised Points
(single EOL)
Normally open and normally closed options (2.2k Ω)
7Supervised Points
(dual EOL)
Normally closed (2.2k Ω)
8Keyswitch Options (single and dual EOL) ((2.2k Ω)
9
Prog Output (PO) 1
Options
Switched 12v Switched Ground Dry Contact
10 Prog Outputs 2 - 4 NF A2P requires that sirens have a backup battery. When this
siren requires a 14,1V to 14,4V supply, use the optional board
EZPS-FRA or the auxiliary power supply IPP-PSU-2A5. Set the
output as interior burglary alarm.
11 2-wire Smoke
Detector Option
EOL resistor (P/N: 25899) required.
12 4-wire Smoke
Detector Option
EOL resistor (P/N: 25899) and Bosch EOL relay module
required
Note: The system uses a 12 VDC battery, connected as shown.
If using RADION devices:
1. Mount the bases for the wireless devices in the desired locations.
Do not attach the wireless devices to the bases at this time.
2. Remove all power from the system.
3. Set the switch on the RADION receiver to normal operating mode = 1.
4. Reapply system power.
Wait for the solid green circle to appear on the control center.
5. Enter the Installer Telephone Menu. Refer to Configuring with the telephone, page 8.
Easy Series Control Panel Wire the Control Panel | en 7
Bosch Security Systems, Inc. Quick Start Guide 2014.09 | 01 | F.01U.306.216
Configure the System
Configure the system using one of the methods described in this section for your control
panel type.
Configuring with the telephone
Refer to Installer Telephone Menu, page 12 for the complete programming menu.
Basic Programming:
1. Enter the Installer passcode (default: 4-digit 5432, 6-digit 543211).
2. Press [3] to enter the Basic Programming menu to make the following changes:
– Modify point types [1][2].
– Record point descriptions [1][1].
– Enter an account number [2][1].
3. Press [#][#][#] to exit Basic Programming.
4. Press [1] to enter System Maintenance to configure wireless devices.
5. Select Wireless Configuration [6] from the System Maintenance menu.
6. After the system prompt, enter the point number (1 to 32) that you want to configure.
The control panel announces the point number and the point type.
If the point number is not currently assigned to a Wireless ID:
To set Point Type, press [1].
To add a device, press [2].
Press [#] to exit.
If the point number is currently assigned to a Wireless ID:
To set Point Type press [1].
To replace a device, press [3]
To delete this device, press [4].
Press [#] to exit.
1. Press [#][#] to exit to the main menu.
2. Press [2] to enter the User Menu to change the installer passcode.
3. Press [1] and change the Installer Passcode.
4. Press [#][#] to exit the User Menu.
Configuring with RPS
In addition to the Installer Phone Menu, you may use RPS to configure an Easy Series control
panel with RADION support. To configure RADION wireless points, specify the following
information for each point:
– Device Type
– Point Type
– Wireless Point ID
– Wireless Alarm Inputs
Since Wireless Alarm Inputs is only available in “Expert Mode”, you must use Expert Mode to
properly configure the Easy Series control panel for RADION wireless devices.
The following table shows the correlation between the current RPS Device Type values and
the RADION Device Types.
1. Once the device type has been selected in RPS, enter the Wireless Point ID and Point
Type via the “wizard” dialog.
3
3.1
3.2
8en | Configure the System Easy Series Control Panel
2014.09 | 01 | F.01U.306.216 Quick Start Guide Bosch Security Systems, Inc.
2. Enter the RFID for the point as specified in the product packaging.
3. Select the desired Point Type from the drop-down menu.
4. Enter an appropriate value in the Wireless Alarm Inputs column.
When setting up an Easy Series control panel to use RADION transmitters, only select from the
RPS device types listed in the table below.
RPS device type RADION transmitter Wireless alarm inputs
PIR motion detector PIR detector (RFPR-12)
PIR curtain detector (RFPR-
C12)
Motion
Dual motion detector Motion detector (RFDL-11) Motion
Wireless device type 3 Repeater (RFRP) None
Smoke detector Smoke detector (RFSM) Smoke
Door Window contact sensor Universal transmitter (RFUN) Wired or magnet
Glass break sensor Glassbreak detector (RFGB) Glass break
Wireless Recessed Point Recessed door/window
contact (RFDW-RM)
Magnet
Wireless Bill Clip Bill trap (RFBT) Magnet
Mini-Door-Window contact Door/window contact (RFDW-
SM)
Magnetic
Notice!
Do not use any other RPS device types when specifying RADION transmitter configurations.
The columns labeled “Wireless Sensor Sensitivity” and “External Power Input” have no effect
on the Radion Wireless Receiver/Transmitter configuration. These fields are not used by the
Easy Panel Radion configuration.
Easy Series Control Panel Configure the System | en 9
Bosch Security Systems, Inc. Quick Start Guide 2014.09 | 01 | F.01U.306.216
Add/Change Users
Enter the User Telephone Menu
1. Connect to the phone test posts or use the house phone.
+
2. Hold down the test button for 10 seconds.
3. Enter the Master Passcode default 1234(55).
Add users
Add Users
1. Enter the User Telephone menu.
2. Enter the Master User (User 1) passcode
3. Press [4] to enter the user menu.
4. Press [1] to add a new user
5. Repeat step 4 for additional users.
Press [#] to return to the User Menu, or [#][#][#] to exit completely.
Change users
Change Users
1. Enter the User Telephone Menu.
2. Enter the Master User (User 1) passcode.
3. Press [4] to enter the User Menu.
4. Press [2] to change a user. Press [2] repeatedly until the system speaks the desired user
number.
5. Repeat Step 4 in Add Users.
6. Press [#] to return to the User Menu, or [#][#][#] to exit completely.
4
4.1
4.2
10 en | Add/Change Users Easy Series Control Panel
2014.09 | 01 | F.01U.306.216 Quick Start Guide Bosch Security Systems, Inc.
Other manuals for ICP-EZM2
3
This manual suits for next models
2
Table of contents
Other Bosch Control Panel manuals
Bosch
Bosch D9412G Troubleshooting guide
Bosch
Bosch FPD-7024 Quick start guide
Bosch
Bosch MPC-xxxx-C Series User manual
Bosch
Bosch ICP-EZM2 User manual
Bosch
Bosch B6512 User manual
Bosch
Bosch FPA-1000-UL User manual
Bosch
Bosch CPS21T User manual
Bosch
Bosch D9412GV4 User manual
Bosch
Bosch Solution 880 CC408 User manual
Bosch
Bosch REXROTH IndraControl VAM 42.1 Technical manual
Bosch
Bosch HPC 400 User manual
Bosch
Bosch Easy Series User manual
Bosch
Bosch CC484 User manual
Bosch
Bosch AddressiFire DS9400M Mounting instructions
Bosch
Bosch D9412GV3 User manual
Bosch
Bosch BE 300 LSN User manual
Bosch
Bosch ICP-CC404 User manual
Bosch
Bosch DS7200V2-UK Assembly instructions
Bosch
Bosch B8512G User manual
Bosch
Bosch AVENAR FPE-8000-SPC User manual
Popular Control Panel manuals by other brands
Mapei
Mapei Mapeheat Thermo Touch user guide
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries SC-SL4-AE2/1 user manual
Sminn
Sminn BOX L VF1L EI instruction manual
Balboa
Balboa TP600 user manual
Nice
Nice HSCU1 Instructions and warnings for installation and use
Truma
Truma CP plus installation instructions