Bosch SCD 110 User manual

SCD110 Sense | Connect | Detect

Operating Instructions / Version 2.0

SCD110 Operating Instructions v2.0 2 | 27

Data subject not change without notice | Printed in Germany | September 20 | Version 1.0

BCDS/GM

Table of Contents

1About the Operating Instructions 5

1.1 Definition of Special Notices ................................................................................................ 5

1.2 Definition of General Notices ............................................................................................... 5

2Safety and Intended Use 5

2.1 Intended Use ........................................................................................................................ 6

2.2 Disposal................................................................................................................................ 6

3Introduction 6

3.1 Scope of Delivery ................................................................................................................. 6

4Technical Specification 7

4.1 Housing ................................................................................................................................ 7

4.2 Dimensions........................................................................................................................... 7

4.3 Device Specifications ........................................................................................................... 8

4.4 Operating Conditions ........................................................................................................... 8

4.5 Sensors ................................................................................................................................ 8

4.6 Measurement Range and Accuracies .................................................................................. 8

4.7 Resolution ............................................................................................................................ 8

4.8 Communication .................................................................................................................... 9

4.9 User Interface....................................................................................................................... 9

4.10 Communication Interfaces ................................................................................................... 9

SCD110 Operating Instructions v2.0 3 | 27

Data subject not change without notice | Printed in Germany | September 20 | Version 1.0

BCDS/GM

5Installation and Start to Use 10

5.1 Mounting the SCD .............................................................................................................. 10

5.2 Connecting to the SCD ...................................................................................................... 10

5.3 SCD App Tabs .................................................................................................................... 12

5.4 Configuring the SCD .......................................................................................................... 13

5.5 Threshold Setting ............................................................................................................... 14

5.6 Streaming ........................................................................................................................... 14

5.7 Data on the Chart............................................................................................................... 15

5.7.1 Chart View Options 16

5.8 Logging and Transferring the Data .................................................................................... 17

5.9 Removing the SCD ............................................................................................................19

5.10 Reusing the SCD ...............................................................................................................19

6General Operating Modes of SCD 20

6.1 General Behavior ...............................................................................................................20

6.2 Resetting the SCD ............................................................................................................. 20

6.3 Streaming via Bluetooth Low Energy (BLE).......................................................................20

6.4 Logging Data into the Local Memory .................................................................................20

6.4.1 Log File Format 21

6.5 Event Detection Mode ........................................................................................................ 22

7Maintenance 22

8Further Product Related Information 23

9Trouble Shooting 23

SCD110 Operating Instructions v2.0 4 | 27

Data subject not change without notice | Printed in Germany | September 20 | Version 1.0

BCDS/GM

10 Regulatory and Legal Information 24

10.1 Target Markets.................................................................................................................... 24

10.2 European Union Notices ....................................................................................................24

10.3 USA: FCC Notices .............................................................................................................25

10.4 Canada: ISED Notices ....................................................................................................... 25

10.5 IMDA Singapore Notices .................................................................................................... 25

10.6 ACMA Australia Notices .....................................................................................................25

10.7 Japan Notice ...................................................................................................................... 26

10.8 South Africa Notice............................................................................................................. 26

10.9 Other Country Certifications............................................................................................... 26

10.10 Bluetooth®..................................................................................................................... 26

10.11 Disposal......................................................................................................................... 26

10.12 Restrictions of Use ........................................................................................................ 26

10.13 Open Source License Condition ................................................................................... 27

SCD110 Operating Instructions v2.0 5 | 27

Data subject not change without notice | Printed in Germany | September 20 | Version 1.0

BCDS/GM

1About the Operating Instructions

This document presents the SCD110 operating instructions, detailed SCD110 sensor characteristics,

communication and management features over the Bluetooth interface.

This document refers to SCD110 firmware version 1.3.0.

Please ensure that your SCD110 device is working correctly by reading these instructions before

using it in your applications.

Please visit the device webpage for more information: https://www.bosch-

connectivity.com/products/sense-connect-detect

1.1 Definition of Special Notices

Warning

Indicates a hazard that could lead to minor or moderate injuries.

Always follow these instructions.

Note

Points of emphasis and reminders of device-specific operational features that could affect

the performance.

Always follow these instructions.

1.2 Definition of General Notices

2Safety and Intended Use

Warning: Do not open the housing!

Opening the housing without authorization will void any warranty and involves risk of injury

to the user. Using the SCD according to its intended use and functions does not require

opening of the housing.

Warning: Damaged housing!

Liquid which enters the device can cause short circuits and damage the device.

This could cause fire, data loss and incorrect measurements.

Warning: Lithium battery!

The device contains a lithium battery that shall not be replaced by the user.

Read and follow the valid transportation regulations for Li batteries in case of air transport

INFO: General information and instructions that must be followed

Tip: Practical advice

SCD110 Operating Instructions v2.0 6 | 27

Data subject not change without notice | Printed in Germany | September 20 | Version 1.0

BCDS/GM

2.1 Intended Use

The SCD110 is designed for monitoring purposes and is not certified as a device to ensure functional

safety. The SCD is intended for the following application areas:

Environments

Residential, commercial, light-industrial, and industrial

Please consider following operating conditions for the SCD110 device.

Operating temperature range

-20 °C … +85 °C

Recommended storage temperature

+10 °C … +30 °C

Humidity range

0% RH … 100% RH

Validation and testing of any use or operation which requires specific requirements and/or standards

that not explicitly mentioned in this document is the customer's responsibility.

Warning: Restricted use!

The SCD shall not be used as an element of control and safety in machines or applications

under the scope of the Machinery Directive 2006/42/EC or other functional safety

regulation. Any incident on health to people and on environment can lead to liability and

criminal prosecution of the user.

Please see also the section 10.12 Restrictions of Use.

2.2 Disposal

Disposing of this product correctly will help save valuable resources and prevent any potential

negative effects to human health and the environment, which could otherwise arise from inappropriate

waste handling. Please contact a certified recycling company or the responsible local authority for

further details on your nearest designated collection point. Penalties may apply for incorrect disposal

of this waste, in accordance with your national legislation. For further information, please refer to the

section 10.11 Disposal.

3Introduction

The SCD is a multi-sensor IoT device that measures acceleration, magnetic fields, temperature and

light. The robust housing, compact design and easy installation make it perfectly suitable for industrial

retrofit applications, such as condition monitoring and predictive maintenance. Configuring the device

enables the user to address a broad variety of use cases.

3.1 Scope of Delivery

The SCD110 will be delivered with the following combination. The devices are ready to use.

SCD110 device with built-in battery

Quick Start Guide

Packaging unit consists of 10 devices

SCD110 Operating Instructions v2.0 7 | 27

Data subject not change without notice | Printed in Germany | September 20 | Version 1.0

BCDS/GM

Note

Please don’t cover the SCD with additional labels or stickers. Otherwise, the function of the light

sensor cannot be guaranteed.

4Technical Specification

4.1 Housing

The SCD is built from a robust housing suited for industrial use with a self-adhesive back.

The compact design of the SCD fits perfectly in different industrial applications and enables easy, user-friendly

mounting in difficult-to-access environments.

For mounting instructions, please refer to 5.1 Mounting the SCD.

4.2 Dimensions

On button

Green/Red LED

Screw holes

SCD110 Operating Instructions v2.0 8 | 27

Data subject not change without notice | Printed in Germany | September 20 | Version 1.0

BCDS/GM

4.3 Device Specifications

4.4 Operating Conditions

4.5 Sensors

INERTIAL SENSORS

ENVIRONMENTAL SENSORS

Accelerometer (3-axis)

Temperature

Magnetometer (3-axis)

Light

4.6 Measurement Range and Accuracies

Note

Specified accuracies refer to the inbuilt sensors. The accuracy and responsiveness of the SCD110

might deviate from sensor specifications, depending on installation conditions and environmental

influences.

4.7 Resolution

ATTRIBUTE

VALUE

Dimension

Length 70.9 mm x Width 62 mm x Height 11.3 mm

Weight

21 g

Power supply

non-rechargeable CR2450 3V Li/MnO2, 490 mAh

Battery Life

up to 2 years depending on configuration and use

Enclosure protection class

IP 67

Electrical protection class

III

Sampling rates (Hz)

Acceleration : 400, 800, 1600, 3200, 6400

Magnetometer : 10

Temperature: 0.05

Light: 1.25, 10

Memory capacity

1 MB

BLE (Bluetooth Low Energy) Activation

In Standby: On push button

During operation: Automatic activation every 3 hours

Target markets and country certifications

See 10.1Target Markets

Environmental certifications

RoHS, REACH

ATTRIBUTE

RANGE

Environments

Residential, commercial, light-industrial, and industrial

Operating temperature range

-20 °C … +85 °C

Recommended storage temperature

+10 °C … +30 °C

Humidity range

0% rH … 100% rH

SENSOR

MEASUREMENT RANGE

ACCURACY

Acceleration

± 200 g

± 10%

Magnetometer

± 1300 µT (X, Y-Axis); ± 2500 µT (Z-

Axis)

± 5%

Temperature

-20 °C … + 85 °C

± 0.25 °C

Light

0 … 188000 Lux

± 15%

SENSOR

RESOLUTION

UNIT

Acceleration

0.1

Magnetometer

µT

Temperature

0.1

°C

Light

lux

SCD110 Operating Instructions v2.0 9 | 27

Data subject not change without notice | Printed in Germany | September 20 | Version 1.0

BCDS/GM

4.8 Communication

4.9 User Interface

4.10 Communication Interfaces

SCD has a Bluetooth Low Energy (BLE) communication interface. The BLE Communication Protocol of SCD is

available in the website to download. With this document SCD can be integrated into any gateway.

BLE

Bluetooth Low Energy V4.2 is currently supported. The SCD always acts as a peripheral device to which

other BLE devices like smartphones, tablets, gateways etc. can establish a connection.

The BLE interface is used, e.g. by a gateway or a mobile app, to:

Configure the SCD.

Transfer data.

ATTRIBUTE

VALUE

Communication

Bluetooth Low Energy

BLE 4.2

Range

up to 40 m (dependent on external influences)

ATTRIBUTE

VALUE

SCD Sensor App

Free smartphone app for configuration, read-out and

visualization. Available for Android and IOS.

SCD110 Operating Instructions v2.0 10 | 27

Data subject not change without notice | Printed in Germany | September 20 | Version 1.0

BCDS/GM

5Installation and Start to Use

5.1 Mounting the SCD

The SCD housing has a self-adhesive back for mounting.

To stick SCD on a surface, the surface must be

flat

dry

clean

Mounting the SCD:

Peel off the protective film.

Stick SCD to the surface.

5.2 Connecting to the SCD

Download the SCD Sensor App. The App is available for free in the Apple App Store or Google Play

Store. Please search for “Bosch SCD” or use the QR-Codes below.

Apple App Store

Google Play Store

Activate Bluetooth on your smartphone.

To activate the SCD, press shortly the button on the device.

Start the SCD Sensor App.

TIP: The SCD can also be attached to the surface of an equipment by using screws.

Other manuals for SCD 110

This manual suits for next models

Table of contents

Other Bosch Accessories manuals

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Siemens

Siemens QSA2700D Basic documentation

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

IFM Electronic

IFM Electronic Efector 250 Series Brief instructions

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual