Boon FROG POD User manual
FROG
POD®
+Bath Toy Scoop, Drain & Storage
+Rangement et égouttoir pour jouets de bain
+ Juguete de baño para recoger, secar y
almacenar de los juguetes
+ Zum Herausschöpfen, Abtropfen lassen und
Aufbewahren von Badewannenspielzeug
Instructions
Instructions
Instrucciones
Anleitung
E
WWARNING
• Prior to installation, remove all internal packaging materials and
fasteners and discard properly.
• The Frog Pod is not a toy!
• NEVER leave child unattended when bathing.
• This product should ALWAYS be used ONLY under adult supervision.
• NEVER apply excessive force to or allow children to hang from the
Frog Pod.
• ALWAYS position the product on the lower portion of the bath wall.
WCAUTION
• Adult assembly required. Tools required (not included): Rubbing
alcohol.
MOUNTING INSTRUCTIONS
Thank you for purchasing a Boon Frog Pod. In order
to hang your Frog Pod, you must first secure the
enclosed bracket to your bath wall.
The enclosed bracket includes three adhesive strips.
This durable adhesive is designed to withstand
moisture. This adhesive forms a semi-permanent
bond on most tile, glass, and fiberglass surfaces and
will hold up to 6 lbs. The adhesive can be removed
without harming the wall surface. Adhesive strips can
only be used once. For replacement adhesive strips or
questions, please visit booninc.com.
IMPORTANT!
FOLLOW INSTRUCTIONS CAREFULLY! The adhesive strips
will NOT stick to the bath wall if you do not follow each
step of the instructions.
The adhesive strips will not stick to silicone-based tile
sealants. DO NOT load the Frog Pod with more than 6 lbs
of toys and accessories.
NOTE: When using the adhesive strips, it is very important
that you place the bracket onto the wall in its proper position
ONLY ONCE. After the adhesive strips are placed on the
wall, DO NOT try to remove and reposition the bracket as
this will prevent the adhesive strips from adhering to the wall.
To attach bracket to the bathtub/shower wall, select an
area where strips are touching the least amount of grout.
If adhesive strips cross grout lines, be sure to firmly press
adhesive into recessed areas.
It is important to maintain a wall surface temperature above
70°F from the time you first place the adhesive strips onto
the wall and throughout the entire 24 hour period before
attaching the base. If you are mounting the adhesive strips
on an exterior wall during cold weather, it may be necessary
to increase the room temperature during this time.
When placing the bracket onto the cleaned wall surface, use
thumb to press firmly over each of the adhesive strips. Rub
while pressing to remove any air bubbles between adhesive
strips and wall surface.
STEPS:
1
10in.
Select a mounting location on the
lower portion of the wall. Leave a
minimum of 10in. between the
bottom of the bracket and any
edge or raised surface of the
bathtub.
2THOROUGHLY clean dirt and
residue from mounting area. Be
certain that you clean the entire
area where the adhesive strips will
be attached.
3Next, VIGOROUSLY wipe
area with rubbing alcohol
using a clean cloth.
4
10 Minutes
Let dry fully for AT LEAST
10 minutes.
5Remove backing from all adhesive
strips. DO NOT TOUCH
ADHESIVE. Hold bracket by its
EDGES ONLY.
6Make sure hook is in the upward
position and level. Place bracket
onto the cleaned area for mounting
and be certain that ALL adhesive
strips are pressed firmly against the
wall. Press FIRMLY for 30 seconds.
7Allow bracket to remain in place
for AT LEAST 24 HOURS before
attaching the base. It is important
to maintain a room temperature of
70°F or above throughout the
entire 24 hour period. Also, avoid
moisture and the use of cleaning
chemicals near the wall bracket
during the 24 hour period.
8To attach base to bracket, fit slot
over bracket hook and snap down
into place.
REMOVING THE ADHESIVE STRIP BRACKET
To remove the adhesive strip bracket, use a flat
object, such as a screwdriver or a butter knife
(covered with a soft cloth to avoid scratching the wall
surface) to pry up one of the adhesive strips. After
loosening the first strip, rotate the bracket to release
the remaining strips. Any adhesive residue remaining
on the wall can be pulled off easily.
USING THE SCOOP
To attach the scoop to the base, simply fit slot over
hook and hang in place. To remove scoop, lift up
then off the hook.
CLEANING & CARE
Remove Frog Pod base from the wall bracket by first
holding the bracket securely in place on the wall, then
pulling the base up and off the bracket hook. Clean
base and scoop with warm water and mild soap.
© 2015 BKD
(A DIVISION OF TOMY •
DIVISION DE TOMY
)
1241 W WARNER RD, SUITE 101
TEMPE, AZ, USA 85284
FOR US AND CANADIAN CUSTOMERS CALL:
POUR LES CLIENTS DES ÉTATS-UNIS
ET DU CANADA: 888.376.4763
BOONINC.COM
TOMY EUROPE
HEMBURY HOUSE, EXETER, EX2 5AZ, UK
B10087-02-INT-001
Consumer: Please retain this packaging for future reference. Actual product styling and colors
may vary. Trademarks and copyrights are exclusively owned by BKD. Made in Mexico.
Au consommateur: conservez cet emballage pour référence. Le style et les couleurs actuelles
peuvent changer. Marques déposées, copyrights et designs sont les propriétés exclusives de
BKD. Fabriqué en Mexique.
Consumidor: Conserve la caja para referencia futura. El estilo y los colores reales del producto
pueden variar. Las marcas comerciales y los derechos de autor y los diseños son propiedad
exclusiva de BKD. Fabricado en México.
Kunden: Bitte bewahren Sie die Verpackung für zukünftige Bezugnahme auf. Ausführung und
Farben des tatsächlichen Produkts können abweichen. Die Marken und Urheberrechte sind
ausschließliches Eigentum von BKD. Hergestellt in Mexiko.
Other Boon Bathroom Fixture manuals
