Blodgett XCEL-50EC User manual

L-920

Rev B

8-01-10

Page 1 of 2

Adjusting the T-Latch on the

Blodgett XCEL-50EC Oven for KFC

Tools Supplied:

C-shaped adjustment gauge

There are two parts to the T-latch:



Base with set screw



T-latch

Returning the T-Latch to Factory Settings

Use this procedure when installing a new gasket

Failure to follow the steps below may

result in damage to the oven and/or door

handle.

When installing a NEW door gasket,

use the C-shaped gauge to set the T-latch back

to the original factory setting. The T-latch must

be returned to the factory setting because if the

door seal is too tight the gasket may be

damaged by over-compression. If the door seal

is too loose, the oven may leak excessively

during the clean cycle and the door switch may

not operate properly.

1. With the door open, place the C-shaped

adjustment gauge over the T-latch. See

Figure 1a. Make sure the legs of the gauge

are touching the face of the oven.

2. If the end of the latch sits in the notch and

hits the edge of the notch when the gauge is

slid up or down, it is properly adjusted.

Figure 1a and 1b

3. The door gasket on the Blodgett XCEL-50EC

Grilled Chicken oven may shrink slightly as it

ages. Therefore, it may be necessary to adjust

the T-latch for the door handle to reduce

leakage during the clean cycle and extend the

life of your gasket. Use the following procedure

to adjust the T-latch on the XCEL-50EC oven.

C-shaped

adjustment

gauge

Be sure end of T-latch sits inside

the notch in the C-shaped gauge

Rubber boot removed from

later version of T-Latch

L-920

Rev B

8-01-10

Page 2 of 2

Adjusting the T-Latch

Use this procedure as the gasket changes over

time.

Figure 2

1. The T-latch is held in place by a set screw

and a jam nut. Using a 13mm wrench,

loosen the jam nut by turning to the left or

counter-clockwise. See Figure 3.

Figure 3

Using a 3/32” Allen wrench, loosen the set

screw on top of the T-latch base. Turn the

set screw 4 full turns.

Figure 4

3. The T-latch has a flat side. See Figure 5. Turn

the T-latch ½ of full turn, or 180°, clockwise to

tighten the door seal. NOTE: When a turn is

completed the flat side of the T-latch must be

facing up, and another one down.

Figure 5

4. Use an Allen wrench to tighten the set screw on

the top of the base.

5. Use a 13mm wrench to tighten the jam nut.

6. Only change ½ of full turn, or 180°, at a time

with

the maximum turns inward being

two

. Test the oven through a clean cycle. If over

time, the door leaks excessively ( an amount

more than what can be contained in the gutter )

during the clean cycle, repeat steps 1-6 to

readjust the T-latch.

Do not adjust the T-

latch in more than two full turns (four ½

turn adjustments) or damage to the door

handle may occur.

Use the C-shaped gauge

to verify if the T-latch is too short. See Figure 6.

When the T-latch has been adjusted in to the

point where it no longer reaches the bump on

the C-gauge, it is time to replace the gasket.

See Figure 6.

Figure 6

T-latch

T-latch base

One of two

flat sides

of T-Latch

Bump on C-Gauge

Other manuals for XCEL-50EC

Other Blodgett Oven manuals

Blodgett

Blodgett S1820G Series User manual

Blodgett

Blodgett 1060 Owner's manual

Blodgett

Blodgett 1415 Owner's manual

Blodgett

Blodgett BCM-101E User manual

Blodgett

Blodgett BE2136 DOUBLE User manual

Blodgett

Blodgett ELECTRIC CONVEYOR OVEN MT1828E User manual

Blodgett

Blodgett BG3240 Manual

Blodgett

Blodgett 901 Base User manual

Blodgett

Blodgett MT2136 Series Installation and operating manual

Blodgett

Blodgett 966 User manual

Blodgett

Blodgett MT2136E/AB Owner's manual

Blodgett

Blodgett MT3255G User manual

Blodgett

Blodgett 951 Base User manual

Blodgett

Blodgett BE2136 DOUBLE Owner's manual

Blodgett

Blodgett 1201 User manual

Blodgett

Blodgett CONVEYOR OVEN MT1820E Application guide

Blodgett

Blodgett S1820E Manual

Blodgett

Blodgett BG2136 Double User manual

Blodgett

Blodgett 1060 User manual

Blodgett

Blodgett CONVEYOR OVEN MT1820E User manual

Blodgett

Blodgett 1048 User manual

Blodgett

Blodgett Double 1000 User manual

Blodgett

Blodgett 1060 Owner's manual

Blodgett

Blodgett IQ2 Operating instructions

Popular Oven manuals by other brands

Bosch

Bosch HVA531NS0 instruction manual

Electrolux

Electrolux EOF6P46X user manual

NEFF

NEFF B44S32 5GB Series instruction manual

Combi

Combi BLODGETT BC142GDS Specifications

AEG

AEG COMPETENCE 311704300 Installation and operating instructions

Falcon

Falcon DOMINATOR PLUS G3106 Series Servicing instructions

Rational

Rational SCC WE 61G installation manual

Smeg

Smeg DOSPA38X User manuals

Electrolux

Electrolux air-o-convect 20 GN 2/1 user manual

Miele

Miele HR 1954-2 operating instructions

KHIND

KHIND OT50 instruction manual

Henny Penny

Henny Penny Smoker Box installation manual

Lang

Lang ECOD-AP Installation and operation instructions

AEG

AEG BEK455310M user manual

Frigidaire

Frigidaire FNGE90JGR user manual

Hotpoint

Hotpoint FE9 S831 JSH IX user manual

GE Advantium SCB2000 owner's manual

AEG

AEG DE401301DM user manual