Blinc MINI-S7 Service manual
Helmet Communication System
Quick Reference Manual
MINI - S7
English - Italiano
Bluetooth® Introduction
This headset is a portable headset solution based on
Bluetooth® wireless technology. Bluetooth® wireless
technology is a short-range radio communication
technology intended to replace the cables
connecting electronic devices. The technology uses
a globally available frequency range intended to
ensure communication compatibility worldwide.
You can connect your headset to your mobile
phone or any device with Bluetooth® wireless
technology that supports the Headset profile or the
Handsfree profile. When the headset is connected
to your mobile phone, you can handle incoming
and outgoing calls, listen to music, and adjust the
volume, using the buttons on the headset. It can
connect to mobiles, music players and GPS systems
that are Bluetooth® enabled. The inbuilt Bluetooth®
Headset in the motorcycle helmet is made up of a
discrete battery unit, control buttons, microphone
and earphone.
Caution:
Listening at full volume to music or voice through
a headset may damage your hearing. Although the
external areas of the helmet are waterproof, you
are advised to ensure the inside elements of the
Bluetooth® device are not exposed to water or any
other foreign substance.
Any warranty does not cover the battery and in all
cases will be void should it be deemed that the user
has caused a malfunction or in any way tampered
with the Bluetooth® device.
BLUETOOTH MODULE
SPEAKERS
CONTROL
BUTTONS
MICROPHONE
Bluetooth® Headset Control Buttons
Power on
Press MFB button about 2 seconds, blue led flash
and prompt“Power on”.
Power off
Press MFB button about 5 seconds, red led flash and
prompt “Power off ”.
Pair with Phone
Please make sure the headset is in power off position.
Push the MFB button for at least 5 seconds till the
LED flashes in red and blue alternately and you will
-
VOLUME
+
VOLUME
Multi Function Button
MFB
VOLUME
INCREASE
VOLUME
DECREASE
BLUE LED RED LED
hear a voice prompt saying“Pairing” in the speakers.
Enable your Bluetooth function on your mobile
phone. Your mobile phone will now scan nearby
devices and find a device named “BLUETOOTH
HELMET”. Please allow your mobile phone to pair
with this device. When pairing has completed and
the headset is ready to use, you will hear a voice
prompt from the headset saying“Pairing successful”
in the speakers.
Once pairing between the two devices is successful,
the LED lights on the headset will change from red
and blue flashing lights to a blue LED light only.
Note: If a PIN code is required by your mobile
phone, please enter“0000”. If you paired the headset
with your phone , the headset will connect your
phone automatically when you turn it on again.
Pairing with a second Bluetooth device or
mobile phone
Multipoint Bluetooth pairing allows the headset to
connect two Bluetooth devices at the same time.
You can pair the first and second Bluetooth device
or mobile phone to the headset by following the
simple procedures in “Pairing with your mobile
phone”.
After second Bluetooth device or mobile phone
confirms that pairing has completed, select the
headset in the list of the devices on your first
Bluetooth device or mobile phone. The headset
is ready to be used for two Bluetooth devices or
mobile phones.
You can pair the first and second Bluetooth device
or mobile phone to the headset by following the
simple procedures in “Pairing with your mobile
phone”.
After second Bluetooth device or mobile phone
confirms that pairing has completed, select the
headset in the list of the devices on your first
Bluetooth device or mobile phone. The headset
is ready to be used for two Bluetooth devices or
mobile phones.
DRIVER & PASSENGER SETTING
SEEKING MODE
Make sure the headset is in power off position.
Press and hold MFB button for at least 5 seconds.
DRIVER & PASSENGER SETTING
BLINKING:
LED flashes in red and blue alternately.
Intercom:
FIRST STEP
SECOND STEP
-
VOLUME
+
VOLUME
-
VOLUME
+
VOLUME
DRIVER SETTING
CONNECT
Press and release immediately MFB button, wait
until the red Led stop blinking.
PASSENGER SETTING
CONNECT
Do nothing, wait for Driver Connection, after this
the red Led stop blinking.
THIRD STEP
-
VOLUME
+
VOLUME
Helmets are now ready for intercom use: intercom
connection will be established between the two
helmets automatically by either driver or passenger
by pressing the MFB button once;
Intercom calls can be terminated pressing MFB
again.
Start/End intercom
Press MFB button to start or end the intercom.
Voice Dial
Rotate the MFB button twice clockwise.
Last number redial
Rotate the MFB button twice anticlockwise.
Answer a Call
When the headset ring, you can press MFB button
to answer the call or the headset will automatically
answer after 8 seconds.
Reject a call
When the headset ring, you can double click MFB
button to reject the call.
Terminate a call
Press MFB button to terminate the call.
Music Play/Pause
Double click MFB button to play or pause the music.
Previous or Next song
Previous song: Turn the MFB button clockwise and
hold about 1 second, and then realese the button to
go to the previouse song. (Some mobile
phones/music players only replay the playing
music )
Next song: Turn the MFB button anticlockwise and
hold about 1 second, and then release the button to
go to the next song.
Adjusting the Volume
Turning the MFB button clockwise or anticlockwise
will adjust the speaker volume during an outgoing
call (mobile phone call or intercom call). Each twise
will adjust volume by one step until maximum or
minimum volume is reached.
Battery Check
Rotate the MFB button and hold 1 second, you will
hear the prompt of the battery capacity.
Low Battery Warning
When the battery is low, the red LED will blink each
5 seconds and you will hear a voice prompt saying
Table of contents
Languages:
Other Blinc Headset manuals
