Black Box SW546A User manual
CUSTOMER
SUPPORT
INFORMATION
Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX
FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
OCTOBER 1996
SW545A
SW546A
Port Manager Switches
Port Manager Switch
ON RDY
ACTIVITY
12345678
Port Manager Switch
ON RDY
ACTIVITY
12345678
ACTIVITY
12345678
FCC AND IC STATEMENTS, TRADEMARKS
3
FEDERAL COMMUNICATIONS COMMISSION
AND
INDUSTRY CANADA
RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio frequency
energy and if not installed and used properly, that is, in strict
accordance with the manufacturer’s instructions, may cause
interference to radio communication. It has been tested and found
to comply with the limits for a Class A computing device in
accordance with the specifications in Subpart J of Part 15 of FCC
rules, which are designed to provide reasonable protection against
such interference when the equipment is operated in a commercial
environment. Operation of this equipment in a residential area is
likely to cause interference, in which case the user at his own
expense will be required to take whatever measures may be
necessary to correct the interference.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise
emission from digital apparatus set out in the Radio Interference
Regulation of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de
classe A prescrites dans le Règlement sur le brouillage radioélectrique
publié par Industrie Canada.
TRADEMARKS USED IN THIS MANUAL
AT and IBM are registered trademarks, and PC/XT is a trademark,
of IBM Corporation.
ProComm is a registered trademark of Symantec Corporation.
PORT MANAGER SWITCHES
NORMAS OFICIALES MEXICANAS (NOM) ELECTRICAL SAFETY STATEMENT
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes
de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para
referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de
operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo,
cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca,
etc.
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales
que sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como
sea recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más
allá a lo descrito en las instrucciones de operación. Todo otro servicio
deberá ser referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no
interfiera su uso. La colocación del aparato eléctrico sobre una cama,
sofá, alfombra o superficie similar puede bloquea la ventilación, no se
debe colocar en libreros o gabinetes que impidan el flujo de aire por los
orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de
calor como radiadores, registros de calor, estufas u otros aparatos
(incluyendo amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo
del tipo descrito en el instructivo de operación, o como se indique en el
aparato.
4
NOM STATEMENT
12. Precaución debe ser tomada de tal manera que la tierra fisica y la
polarización del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no
sean pisados ni pellizcados por objetos colocados sobre o contra ellos,
poniendo particular atención a los contactos y receptáculos donde salen
del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las
recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las
lineas de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no
sea usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean
derramados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del
aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en
su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
5
PORT MANAGER SWITCHES
Contents
Chapter Page
1. Specifications ............................................................................................. 7
2. Introduction ............................................................................................. 11
2.1 General Overview .............................................................................. 11
2.2 The Port Manager Switches Illustrated ........................................... 13
3. Getting Started ......................................................................................... 15
3.1 Setting Default Communication Parameters .................................. 15
3.2 Connecting Your PC to the PM Switch ............................................ 16
3.3 Applying Power to the PM Switch .................................................... 17
3.4 Communicating with the PM Switch Unit ....................................... 18
4. Installation ................................................................................................ 22
4.1 Setting the SETUP Switch ................................................................ 22
4.2 Connecting a Modem to the PM Switch .......................................... 25
4.3 Initializing the Unit to Default Settings .......................................... 26
4.4 Connecting Devices to the PM Switch ............................................. 26
5. Configuration ........................................................................................... 28
5.1 Accessing the PM Switch’s Command Mode .................................. 28
5.2 Defining and Reading the Site I.D. ................................................... 29
5.3 Port Configuration ............................................................................ 30
6. Operation ................................................................................................. 36
6.1 Connecting and Disconnecting Ports .............................................. 36
6.2 Defining Hunt Groups ..................................................................... 39
6.3 Port Buffers ....................................................................................... 41
6
7
TABLE OF CONTENTS
Chapter Page
7. Saving Configuration Parameters ............................................................ 42
7.1 Sending Parameters to a File ............................................................ 42
7.2 Restoring Saved Parameters ............................................................. 43
8. Command Reference Guide ................................................................... 44
8.1 Command Conventions .................................................................... 44
8.2 Command Response ......................................................................... 45
8.3 Command Summary ......................................................................... 46
8.4 Command Set .................................................................................... 47
9. Troubleshooting ...................................................................................... 56
9.1 Calling Black Box .............................................................................. 56
9.2 Shipping and Packaging ................................................................... 56
Appendix A: Pinouts .........................................................................................57
Appendix B: SW546A-D48 ................................................................................62
8
PORT MANAGER SWITCHES
Compliance — FCC Class A, IC Class/classe A
Interfaces — Proprietary modular serial, compatible with EIA
RS-232 (DTE)
Protocol — Asynchronous
Code Set — ASCII
Data Format — Either 8 data bits, no parity, or 7 data bits, even or
odd parity; either 1 or 2 stop bits (independently
user-selectable for each port)
Flow Control — DTR/CTS (hardware), X-ON/X-OFF (software), or
both (independently user-selectable for each port)
Operation —
Full duplex (command echo) or half-duplex (no echo),
user-selectable
Data Rate — 38,400, 19,200, 9600, 4800, 2400, 1200, or 300 bps
(independently user-selectable for each port)
Maximum
Distance — Up to 150 ft. (45.7 m); might be less if you use flat-
Internal Memory — 256 KB battery-backed, autoconfiguring, dynamically
allocated buffer SRAM on SIMMs (or DIPs in some
units); units with 512 KB are available as special
quotes
1. Specifications
9
CHAPTER 1: Specifications
User Controls — Keyboard commands;
(2) Front-mounted CLEAR and SET pushbuttons;
(3) Rear-mounted:
(1) 8-position DIP switch for comm. parameters;
(1) 115-/220-VAC slide switch;
(1) OFF/ON rocker switch
Indicators — All front-mounted:
Both models: ON and RDY (ready) LEDs;
SW545 models: (8) ACTIVITY LEDs;
SW546 models: (16) ACTIVITY LEDs
Connectors — All rear-mounted:
All models: (1) IEC 320 male power inlet;
SW545 models: (8) RJ-11 female;
SW546 models: (16) RJ-11 female
Leads/Signals
Supported — Ports 1 and 2:
Pins 1 through 6 (CTS in, SGND, RD in, RLSD
[DCD] in, TD out, and DTR out respectively);
Ports 3 and up:
Pins 1 through 6 (CTS in, SGND, RD in, RTS [held
high], TD out, and DTR out respectively)
Power — From outlet through 6-ft. (1.8-m) power cord
(included with SW545 units only) and internal
power supply:
Either 115 VAC, 60 Hz or 220 VAC, 50 Hz (user-
selectable);
Consumption: 5 watts
Fuse — 250 volts, 125 mA Slo-Blo
Temperature
Tolerance — 32 to 122˚ F (0 to 50˚ C)
10
PORT MANAGER SWITCHES
Humidity
Tolerance — 20 to 80% noncondensing
Size — 1.8" (1U) H x 17"W x 6.5"D (4.4 x 43.2 x 16.5 cm);
when rackmount brackets are added, the unit is
19" (48.3 cm) wide
Weight — 6 lb. (2.7 kg)
11
CHAPTER 2: Introduction
2.1 General Overview
With our 8-port and 16-port Port Manager (PM) Switches, you can control
and manage a network without having to worry about the in-band restrictions
associated with SNMP. Both models of the Switch make it possible to establish
on-site or remote communication with any piece of equipment that has an RS-
232 command port. You can access such devices without having to travel to
the installation site, even when your network is down.
Versatile Connectivity
The PM Switch provides a practical solution for applications that require
communicating with devices using dissimilar data rates. You can individually
tailor the Switch’s 8 or 16 ports for specific data rates, data formats, types of
flow control, and various other custom parameters and options.
Easy Setup and Operation
Configuring the PM Switch is simple. You can select communications
parameters or enable or disable options through a convenient menu system.
The Switch can be easily configured to fit the requirements of almost any
data-communications application.
Limited Command Access
The PM Switch is ideal for situations that require two tiers of command/
configuration security. You can individually configure the Switch’s ports
either as Administrator ports with access to all commands, or as User ports
with access to basic commands only.
Modular Design
The PM Switch’s RJ-11 jacks can be quickly and easily connected (through
RS-232 modular adapters) to computers, modems, and other LAN/WAN
hardware. The Switch is compact and occupies only one rack unit (1.75
inches) of vertical rack space.
Buffered Ports
The PM Switch has 256 KB of nonvolatile, dynamically allocated buffer
memory that prevents data from overflowing during communication sessions.
If your application requires more memory, call Black Box for technical
support; they might be able to provide you with a quote on units with 512-KB
buffers.
2. Introduction
This manual suits for next models
1
Table of contents
Other Black Box Switch manuals
Black Box
Black Box LP004A User manual
Black Box
Black Box KV7012A User manual
Black Box
Black Box KV9304A User manual
Black Box
Black Box sW901aE User manual
Black Box
Black Box AC447A User manual
Black Box
Black Box ServSwitch SW721A-R5 User manual
Black Box
Black Box ServSwitch Duo IPC KV6216FA-R2 User manual
Black Box
Black Box IC147A-R2 User manual
Black Box
Black Box 10BASE-T MiniHub User manual
Black Box
Black Box LT7002A User manual
Black Box
Black Box SS4P-SH-DVI-UCAC-P User manual
Black Box
Black Box SW540A-R3 User manual
Black Box
Black Box SW970A User manual
Black Box
Black Box KV6224A User manual
Black Box
Black Box PI750A User manual
Black Box
Black Box SW1023A User manual
Black Box
Black Box ServSwitch TDX User manual
Black Box
Black Box ServSelect KV124A-PS2 User manual
Black Box
Black Box MEG801AE User manual
Black Box
Black Box ServSwitch 4site User manual
