Black Box SHM-B Plus Async Series User manual
JUNE 2002
ME800A-PLUS
ME800AE-PLUS
Short-Haul Modem B (SHM-B)
Plus Async
CUSTOMER SUPPORT INFORMATION
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
TD
RD
NORMAL
LOOPBACK
1
FCC/IC RFI STATEMENTS, TRADEMARKS
FEDERAL COMMUNICATIONS COMMISSION AND
INDUSTRY CANADA
RADIO-FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio-frequency energy, and if
not installed and used properly, that is, in strict accordance with the
manufacturer’s instructions, may cause interference to radio communication.
It has been tested and found to comply with the limits for a Class A computing
device in accordance with the specifications in Subpart B of Part 15 of FCC rules,
which are designed to provide reasonable protection against such interference
when the equipment is operated in a commercial environment. Operation of
this equipment in a residential area is likely to cause interference, in which case
the user at his own expense will be required to take whatever measures may be
necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emission from
digital apparatus set out in the Radio Interference Regulation of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de classe A prescrites dans le Règlement sur le
brouillage radioélectrique publié par Industrie Canada.
TRADEMARKS USED IN THIS MANUAL
BLACK BOX and the logo are registered trademarks of Black Box
Corporation.
Any other trademarks mentioned in this manual are acknowledged to be the property of the
trademark owners.
2
SHM-B PLUS ASYNC
NORMAS OFICIALES MEXICANAS (NOM)
ELECTRICAL SAFETY STATEMENT
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes
de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para
referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de
operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo,
cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca,
etc..
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales
que sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más
allá a lo descrito en las instrucciones de operación. Todo otro servicio
deberá ser referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no
interfiera su uso. La colocación del aparato eléctrico sobre una cama,
sofá, alfombra o superficie similar puede bloquea la ventilación, no se
debe colocar en libreros o gabinetes que impidan el flujo de aire por los
orificios de ventilación.
3
NOM STATEMENT
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor
como radiadores, registros de calor, estufas u otros aparatos (incluyendo
amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del
tipo descrito en el instructivo de operación, o como se indique en el
aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la
polarización del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no
sean pisados ni pellizcados por objetos colocados sobre o contra ellos,
poniendo particular atención a los contactos y receptáculos donde salen
del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las
recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las
lineas de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no
sea usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean
derramados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del
aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en
su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
4
SHM-B PLUS ASYNC
Contents
Chapter Page
1. Specifications .............................................................. 5
2. Introduction ............................................................... 8
3. Installation and Configuration .................................. 9
3.1 Making the Four-Wire Connection .................... 9
3.2 Making the RS-232 Connections ...................... 12
3.3 Setting the DTE/DCE Switch (S1) ................... 13
3.4 Setting the Flow-Control Switch (S3) ............... 15
4. Operation .................................................................. 17
5. Troubleshooting ....................................................... 19
5
CHAPTER 1: Specifications
1. Specifications
Data Rate and Maximum Distance:
Data Rate (bps) AWG (mm)
24 (0.5) 26 (0.4)
Distance in miles
115,200 0.8 0.7
57,600 1.2 0.8
38,400 1.3 0.9
19,200 1.5 1.2
9600 2 1.5
4800 2.6 2
2400 4 3
1200 4.8 4
NOTE: The above specifications are valid for 24- or 26-AWG unshielded
twisted-pair telephone cable insulated by polyethylene with a
mutual capacitance of 0.083 pF/mile (0.52 pF/km). Shielded
twisted-pair cable will reduce the distance to one-third of the table
value, due to the additional capacitance contributed by the cable’s
shielding. Actual distances may vary depending on your specific
operating equipment and the cable you use.
Protocol: Asynchronous
Operation: 4-wire, full duplex, point-to-point
Line Interface: Balanced current loop; receive lines are
protected through optical isolators rated at 1500 volts
6
SHM-B PLUS ASYNC
Equipment Interface: TIA/EIA RS-232/ITU V.24
interface with a hardware handshake (selected through
use of an external switch); Data Carrier Detect (DCD)
true (high) indicates operating short-haul modem at the
remote end of the loop; interface is switch-selectable for
DTE/DCE configuration (pins 2 and 3 reversed, pins 4
and 5 reversed with pin 8, pin 6 reversed with pin 20)
Connectors: (1) DB25 female, (1) 4-screw terminal
block, (1) RJ-11 female (6 positions, 6 contacts),
(1) 4-pin mini-DIN female
Diagnostics: Loopbacks provided by a front-panel switch:
Analog loopback on a 4-wire loop and digital loopback
on equipment interface (RS-232)
Indicators: (2) Front-mounted bi-color LEDs indicate
the status of the RS-232 transmitter and receiver: green
indicates a “low” logic level (-3 to -15V), red indicates a
“high” logic level (+3 to +15V)
Temperature Tolerance: 32 to 112°F (0 to 50°C)
Humidity Tolerance: Up to 90% noncondensing
Enclosure: High-impact plastic
7
CHAPTER 1: Specifications
Power: From external power supply (no more than
16 Vrms is present in unit):
Input (ME800A-PLUS): 115 VAC ±10%, 60 Hz, 5 watts
(12 watts maximum);
Input (ME800AE-PLUS): 230 VAC ±10%, 50/60 Hz;
Output (both models): 17 VAC, 700 mA
Size: 1.3"H x 4"W x 4.2"D (3.3 x 10.2 x 10.7 cm)
Weight: 1.4 lb. (0.6 kg), standalone, including
transformer
8
SHM-B PLUS ASYNC
2. Introduction
The Short-Haul Modem Model B Plus Async (SHM-B
Plus Async) is a standalone asynchronous full-duplex
4-wire line driver/receiver which allows two TIA/EIA
RS-232 devices to communicate at distances of up to
4.8 miles (7.7 km) or at data rates up to 115.2 kbps.
In addition to the transmitter and receiver circuits, the
SHM-B Plus Async includes RS-232 control-line
interfaces, status-monitor LEDs, and a loopback switch.
The 115-VAC version is product code ME800A-PLUS;
the 230-VAC version is product code ME800AE-PLUS.
The SHM-B Plus Async is designed to operate over a
4-wire metallic circuit. Optimum performance is
obtained with twisted-pair cable (see Chapter 1). Most
types of twisted-pair cable may be used, often with little
or no performance degradation.
The SHM-B Plus Async is designed for maximum
operator safety. There are no voltages greater than
12 VDC or 16 VAC present on the circuit board of the
unit. The Receive lines are protected from potential
ground differences through optical isolators rated at
1500 volts.
9
CHAPTER 3: Installation and Configuration
3. Installation and Configuration
You can install and configure the SHM-B Plus Async in
three basic steps: making the four-wire connections,
making the RS-232 connection, and setting the switches.
3.1 Making the Four-Wire Connections
Connect a pair of SHM-B Plus Async modems to each
other through either their terminal blocks or their RJ-11
connectors. Figure 3-1 on the next page shows the
location of the terminal block and the RJ-11 jack.
a) TERMINAL BLOCK:
Refer to Figure 3-2 to make the proper connections
between two SHM-B units using the terminal block.
NOTE: Transmit + (TX+) on one modem is wired
to Receive + (RX+) on the other modem; Transmit -
(TX-) is wired to Receive - (RX-).
1. Strip each of the four wires about 1⁄8".
2. Loosen the screw terminals in the terminal block.
Insert the wires into the terminal strip; tighten the
screw terminals.
This manual suits for next models
2
Table of contents
Other Black Box Modem manuals
Black Box
Black Box 3600 User manual
Black Box
Black Box ME0004C-G703 User manual
Black Box
Black Box MDR24x User manual
Black Box
Black Box MDU9705A-V35 User manual
Black Box
Black Box ME0002A-V35 User manual
Black Box
Black Box MC119A User manual
Black Box
Black Box MDS932AE-10BT-R2 User manual
Black Box
Black Box MDS932AE-10BT User manual
Black Box
Black Box ME800A User manual
Black Box
Black Box MD3400A User manual
Black Box
Black Box RM1600 User manual
Black Box
Black Box MDS931AE-10BT User manual
Black Box
Black Box SHM-FSK User manual
Black Box
Black Box Mini-Modem V.92 MD1626A User manual
Black Box
Black Box Industrial Control MDU20G-918 User manual
Black Box
Black Box MD960A User manual
Black Box
Black Box ME560A-V35-F User manual
Black Box
Black Box SME-422 User manual
Black Box
Black Box MD640A-ST-R2 User manual
Black Box
Black Box MT632A-ST35 User manual
