Black Box ME0006A-V35 User manual

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)

FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

NOVEMBER 2001

ME0006A-V35

ME0006A-X21

2-Wire Short-Range DSL Line Driver

(HDSL with V.35)

(HDSL with X.21)

FCC AND IC RFI STATEMENTS/CE NOTICE

FEDERAL COMMUNICATIONS COMMISSION

AND

INDUSTRY CANADA

RADIO FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio frequency energy and if not

installed and used properly, that is, in strict accordance with the manufacturer’s

instructions, may cause interference to radio communication. It has been tested

and found to comply with the limits for a Class A computing device in accordance

with the specifications in Subpart B of Part 15 of FCC rules, which are designed to

provide reasonable protection against such interference when the equipment is

operated in a commercial environment. Operation of this equipment in a

residential area is likely to cause interference, in which case the user at his own

expense will be required to take whatever measures may be necessary to correct

the interference.

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise emission from

digital apparatus set out in the Radio Interference Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le

brouillage radioélectrique publié par Industrie Canada.

EUROPEAN UNION DECLARATION OF CONFORMITY

This equipment complies with the requirements of the European EMC Directive

89/336/EEC.

2-WIRE SHORT-RANGE DSL LINE DRIVER (HDSL WITH V.35 OR X.21)

NORMAS OFICIALES MEXICANAS (NOM)

ELECTRICAL SAFETY STATEMENT

INSTRUCCIONES DE SEGURIDAD

1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de

que el aparato eléctrico sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas para

referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de

operación deben ser respetadas.

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca

de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc..

6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que

sean recomendados por el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea

recomendado por el fabricante.

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá

a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser

referido a personal de servicio calificado.

9. El aparato eléctrico debe ser situado de tal manera que su posición no

interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,

alfombra o superficie similar puede bloquea la ventilación, no se debe colocar

en libreros o gabinetes que impidan el flujo de aire por los orificios de

ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor

como radiadores, registros de calor, estufas u otros aparatos (incluyendo

amplificadores) que producen calor.

11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del

tipo descrito en el instructivo de operación, o como se indique en el aparato.

NOM STATEMENT

12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización

del equipo no sea eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera que no

sean pisados ni pellizcados por objetos colocados sobre o contra ellos,

poniendo particular atención a los contactos y receptáculos donde salen del

aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las

recomendaciones del fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas

de energia.

16. El cable de corriente deberá ser desconectado del cuando el equipo no sea

usado por un largo periodo de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean

derramados sobre la cubierta u orificios de ventilación.

18. Servicio por personal calificado deberá ser provisto cuando:

A: El cable de poder o el contacto ha sido dañado; u

B: Objectos han caído o líquido ha sido derramado dentro del aparato; o

C: El aparato ha sido expuesto a la lluvia; o

D: El aparato parece no operar normalmente o muestra un cambio en su

desempeño; o

E: El aparato ha sido tirado o su cubierta ha sido dañada.

2-WIRE SHORT-RANGE DSL LINE DRIVER (HDSL WITH V.35 OR X.21)

TRADEMARKS USED IN THIS MANUAL

Any trademarks mentioned in this manual are acknowledged to be the property of the

trademark owners.

CONTENTS

Contents

Chapter Page

1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3. Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.1 Connecting the Twisted-Pair Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.2 Connecting the HDSL Line Driver’s V.35 Serial Interface . . . . . . . . . . . 15

4.2.1 Connecting the V.35 Line Driver to a DTE Device . . . . . . . . . . . . . . 15

4.2.2 Connecting the V.35 Line Driver to a DCE Device . . . . . . . . . . . . . . 15

4.3 Connecting the Line Driver’s X.21 Serial Interface . . . . . . . . . . . . . . . . . 16

4.3.1 Connecting the X.21 Line Driver to a DCE or DTE Device . . . . . . . 16

4.3.2 Opening the Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.4 Connecting Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5. Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

5.1 Power-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

5.2 LED Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

5.3 Test Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5.3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5.3.2 Restart Procedure and Timeouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5.3.3 Loops and Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

5.3.4 Using the V.52 (BER) Test-Pattern Generator . . . . . . . . . . . . . . . . . . 27

Appendix A. V.35 Interface Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Appendix B. X.21 Interface Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Appendix C. Transmission Distance Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

2-WIRE SHORT-RANGE DSL LINE DRIVER (HDSL WITH V.35 OR X.21)

1. Specifications

Clocking Modes: Internal, external, or receive recovered

DTE Rate: All 64-kbps increments from 64 to 1152 kbps

DTE Interface: ME0006A-V.35: DCE orientation; ME0006A-X.21: DCE or DTE

DTE Connector: ME0006A-V.35: M/34 female; ME0006A-X21: DB15 female

Diagnostics: V.52-compliant (511/511E) pattern generator and detector with error

injection mode controlled by a front-panel switch; local and remote loopback

controlled by either a front-panel switch or from the DTE interface

Indicators: LEDs: DSL Link (green active); TD (yellow/green) idle yellow; RD

(yellow/green) idle yellow; NS (red active); No signal DSL Link; ER (flashing red)

CRC error during normal operation, bit error during pattern-generation test; TM

(active yellow) Test Mode enabled

Configuration: Externally accessible DIP switches or SNMP managed through

ME0003C

Transmission Line: Single twisted pair

Line Coding: 2B1Q

Line Rates (DSL Line): 144, 272, 400, 528, 784, 1040, 1168 kbps

Line Interface: Transformer coupled, 1500-VAC isolation

Connection: RJ-45, 2-wire, polarity insensitive pins 4 and 5

Operating Temperature: 32 to 122°F (0 to 50°C)

Humidity: 5 to 95% noncondensing

Altitude: Up to 15,000 ft. (4572 m)

Power: External desktop transformer, 100 to 240 VAC, 50 to 60 Hz (universal

input), 10 W

Size: 1.6"H x 4.7"W x 6"D (4.1 x 11.9 x 15.2 cm)

Weight: 0.58 lb. (0.26 kg)

CHAPTER 2: Introduction

2. Introduction

2.1 Description

The 2-Wire Short-Range DSL Line Driver (HDSL) V.35 or X.21 provides

high-speed 2-wire connectivity to ISPs, PTTs, and corporations using HDSL (High

Bit-Rate Digital Subscriber Line) technology. Supporting multiple line rates from

144 kbps to 1.168 Mbps, the Line Driver provides megabyte speeds to leased line,

LAN-to-LAN interconnection, and WAN access networks over 3.6 miles/5.8 km

(1.054 Mbps on 24-AWG/0.5-mm wire).

The HDSL Line Driver V.35 (ME0006A-V35) provides a V.35 interface on an M/34

female connector. The HDSL Line Driver X.21 (ME0006A-X21) provides an X.21

interface on a DB15 female connector. Features include loopback diagnostics, and

inband SNMP/HTTP remote management capabilities through a DSL Line Driver

Rack Card (ME0003C) CO and externally accessible configuration switches. Both

versions of the Line Driver are compatible with the popular QuikConnect HDSL

Line Driver (ME0007A-HDSL) standalone and DSL Line Driver Rack Card

(ME0003C) as well as the HDSL Line Driver 10BASE-T (ME0006A-10BT).

As a symmetric DSL NTU, the HDSL Line Driver offers the same data rates in both

directions over a single pair of regular telephone lines using 2B1Q modulation.

Line connection is made by an RJ-45 jack. The Line Driver is powered by a 100- to

240-VAC universal power supply.

2.2 Features

• High bit-rate DSL.

• 2B1Q modulation.

• DTE rates up to 1.152 Mbps.

• V.35 and X.21 interfaces.

• Interoperable with ME0003C and ME0007A.

• SNMP Manageable via Managed Micro Rack SNMP/HTTP Card (RM261C-

SNMP) through ME0003C/CO.

• Universal power supply.

• Front-panel status indicators.

• Small, convenient desktop unit.

• CE marked.

2-WIRE SHORT-RANGE DSL LINE DRIVER (HDSL WITH V.35 OR X.21)

3. Configuration

The HDSL Line Driver is equipped with two sets of eight DIP switches. This

chapter describes switch locations and explains all possible configurations.

Configuring the Hardware DIP Switches

The 16 external switches are grouped into two eight-switch sets. They’re externally

accessible from the underside of the HDSL Line Driver (see Figure 3-1).

Figure 3-1. Underside of the HDSL Line Driver,

showing the location of the DIP switches.

The two sets of DIP switches on the underside of the HDSL Line Driver are called

S2 and S3. As Figure 3-2 shows, the orientation of all DIP switches is the same with

respect to ON and OFF positions.

Figure 3-2. Close-up of configuration switches

(all sets are identical in appearance).

ON OFF

CHAPTER 3: Configuration

DIP-S

WITCH

The configuration switches on S2 allow you to specify the clocking mode and to

enable/disable local and remote loop requests from the V.35 DTE. Default settings

are shown in Table 3-1.

Table 3-1. S2 summary.

Position Function Factory Default

S2-1 Reserved Off

S2-2 Reserved Off

S2-3 Reserved Off

S2-4 Reserved Off

S2-5 Reserved Off

S2-6 Clock Mode On

S2-7 Clock Mode Off

S2-8 Enable loop from DTE Off Disabled

Switch S2-1, S2-2, S2-3, S2-4, and S2-5:

Reserved for factory use and must remain in the OFF position.

}Receive Recover

This manual suits for next models

Table of contents

Other Black Box Extender manuals

Black Box

Black Box ACU1007A User manual

Black Box

Black Box Wizard AVU5001A User manual

Black Box

Black Box ServSwitch Duo KV6EXTB-R2 User manual

Black Box

Black Box ServSwitch ACUDLY User manual

Black Box

Black Box ACS1009A-xx User manual

Black Box

Black Box ACS253A-CT User manual

Black Box

Black Box LB401A User manual

Black Box

Black Box ACU5800A Wizard DP Assembly instructions

Black Box

Black Box LB512A-KIT User manual

Black Box

Black Box LWE120A User manual

Black Box

Black Box MTU9230 User manual

Black Box

Black Box ServSwitch ACU2500A User manual

Black Box

Black Box LB300A-RACK User manual

Black Box

Black Box Abeo G.703 LAN Installation and operating instructions

Black Box

Black Box ACX2MT Series User manual

Black Box

Black Box LWE100A User manual

Black Box

Black Box LR0202A-KIT User manual

Black Box

Black Box ACS335A User manual

Black Box

Black Box 39004 User manual

Black Box

Black Box ServSwitch ACU5116A User manual

Black Box

Black Box ServSwitch ACU1001A User manual

Black Box

Black Box IC502A-R2 User manual

Black Box

Black Box CampusLIGHT LCL114A-FEMM User manual

Black Box

Black Box Wizard ACU50 A Series User manual

Popular Extender manuals by other brands

SY HDBT-60T installation guide

Appsys ProAudio

Appsys ProAudio ADX-16 user manual

Atlona

Atlona RS232 user manual

IDK

IDK OPF-TH1000-A user guide

Enable-IT

Enable-IT 824WP quick start guide

Worx

Worx Landroid RadioLink WA0864 Get started

TP-Link

TP-Link TL-WA730RE user guide

Camplex

Camplex CMX-HDMI-SFPL user manual

SC&T

SC&T HE03-4K user manual

Marmitek

Marmitek MegaView70 user manual

Samsung

Samsung SCS-26UC4 user guide

Foxun

Foxun SX-GES24 operating instructions

MuxLab

MuxLab 500771 Operation manual

foxunhd

foxunhd SX-AEX01 operating instructions

TERK Technologies

TERK Technologies LFIRX2 owner's manual

Devolo

Devolo Audio Extender supplementary guide

Edimax

Edimax EW-7438RPn V2 instructions

Shinybow USA

Shinybow USA SB-6335T5 instruction manual