Binatone SPEAKEASY 5 User manual
1
2
3
2. Installation
4
1. Locating the Base unit
The Base unit should be placed on a level surface, in a position where:
the telephone line cable will reach your telephone line socket or
extension socket.
it is not close to a sink, bath or shower, or anywhere else where it
might get wet.
it is not close to other electrical equipment - fridges, washing
machines, microwave ovens, TVs, fluorescent lights, etc.
2. Plug the coiled handset cord into the Handset. Plug the other end into
the jack on the left side of the Base unit.
3. Place the Handset in the Base unit.
4. Plug the telephone line cord into the
PHONE LINE jack at the back of the
Base unit. Plug the other end
into a modular wall jack.
5. Lift the Handset and
check for Dial tone in
the earpiece.
Always use the telephone
line cord supplied with your
SpeakEasy 5. Other telephone
line cords may not work.
Installing Backup
batteries
1. Remove the Battery cover and insert
3 X 1.5V AA size alkaline batteries
(not included) into the battery
compartment paying attention to the
polarity marking as shown inside the
compartment.
2. Replace the battery cover until it
clicks into place.
Note: The Caller display will not work without batteries installed.
Warning: Disconnect the telephone
from the telephone line before
changing the batteries.
3. Desk/Wall mount installation
5
To place the SpeakEasy 5 on a desk, connect
the stand to the bottom of the phone in the
slots near the ringer cover as shown below.
Desk Mount
Insert the rigid clips of the stand into the slots
on the bottom of the phone (near the ringer
cover). Press down firmly until the flexible
clips clicks into place.
To remove the stand, (1) pinch the flexible
clips, (2) pull back the stand, and then (3)
slide up and forward (3) as shown below.
To place the SpeakEasy 5 on a wall, connect
the stand to the bottom of the phone in the
slots near the battery cover as shown below.
Wall Mount
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677
Calls are charged at Local Call rate.
Desk/Wall mount continue...
Insert the rigid clips of the stand into the slots
on the bottom of the phone (near the battery
cover). Press down firmly until the flexible
clips clicks into place.
To remove the stand, (1) pinch the flexible
clips, (2) pull back the stand, and then (3)
slide up and forward as shown below.
Mark two points on the wall that are 137mm
apart to lay the fixing centers as shown below.
BE CAREFUL to check that there are no
electrical wires hidden in the wall.
Fix two screws (supplied with the unit) at the
marked locations, leaving approximately 7mm
between the wall and the the screw head.
Hang the cradle unit on the screws using the
wall mount slots. You may need to remove the
telephone from the wall and tighten the
screws so that the cradle is securely fixed and
does not wobble. Place the Handset on the
cradle with the parking hook on the cradle
arranged to fit in the parking recess under the
earpiece on the Handset.
6
7
4. Setting up your phone
The following section details how to set up your
telephone. Press the MENU button to enter the
Options menu and then use the UP or DOWN
buttons to cycle through the following options:
SET LANGUAGE
SET TIME/DATE
LCD CONTRAST
SET FLASH TIME
EXIT OPTION
Note: The system will time out if you leave
more than 15 seconds between key presses.
!
With the phone in standby mode:
1 Press MENU button.
ÖThe display shows
OPTIONS MENUOPTIONS MENU
OPTIONS MENUOPTIONS MENU
OPTIONS MENU
.
2 Press UP button to go to the language setting.
ÖThe display will show
SET LANGUAGESET LANGUAGE
SET LANGUAGESET LANGUAGE
SET LANGUAGE
.
3 Press MENU button to confirm.
4 Press UP or DOWN button to select one of the
11 languages: ENGLISH, FRENCH, SPANISH,
GERMAN, ITALY, PORTUGUESE, TURKISH,
DANISH, POLISH, SWEDISH, and DUTCH.
5 Press MENU button to confirm.
6 Continue with programming, or press RECALL
button to return to standby mode.
SET
LANGUAGE
The date and time on your phone can be
synchronized with the local date and time if
you have subscribed to the Caller Display
service from your telephone company. (This
feature is only available for an analogue PSTN
(not ISDN) line).
However, you can set the date and time manually:
1 Press MENU button.
ÖThe display shows
OPTIONS MENUOPTIONS MENU
OPTIONS MENUOPTIONS MENU
OPTIONS MENU .
SET TIME/
DATE
Setting up continue...
8
2 Press UP or DOWN button until the display
shows
SET TIME/DATESET TIME/DATE
SET TIME/DATESET TIME/DATE
SET TIME/DATE
.
3 Press MENU button to confirm.
ÖThe ‘year’ icon will be blinking.
4 Press UP or DOWN button to set the year.
5 Press MENU button to confirm.
ÖThe ‘month’ icon will be blinking.
6 Press UP or DOWN button to set the month.
7 Press MENU button to confirm.
ÖThe ‘date’ icon will be blinking.
8 Press UP or DOWN button to set the date.
9 Press MENU button to confirm.
ÖThe ‘hour’ icon will be blinking.
10 Press UP or DOWN button to set the hour.
ÖWhen setting the ‘hour’, the ‘AM’ or ‘PM’
icon will automatically turn ON to correspond
the hour time.
11 Press MENU button to confirm.
ÖThe ‘minute’ icon will be blinking.
12 Press UP or DOWN button to set the minute.
13 Press MENU button to confirm the TIME and
DATE setting.
14 Continue with programming, or press RECALL
button to return to standby mode.
1 Press MENU button.
ÖThe display shows
OPTIONS MENUOPTIONS MENU
OPTIONS MENUOPTIONS MENU
OPTIONS MENU
.
2 Press UP or DOWN button until the display
shows
LCD CONTRASTLCD CONTRAST
LCD CONTRASTLCD CONTRAST
LCD CONTRAST
.
LCD
CONTRAST
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677
Calls are charged at Local Call rate.
Setting up continue...
9
3 Press MENU button to confirm.
4 Press UP or DOWN button to select your
comfortable display viewing level (1~6). The
default setting is 3.
5 Press MENU button to confirm the LCD
CONTRAST setting.
6 Continue with programming, or press RECALL
button to return to standby mode.
1 Press MENU button.
ÖThe display shows
OPTIONS MENUOPTIONS MENU
OPTIONS MENUOPTIONS MENU
OPTIONS MENU
.
2 Press UP or DOWN button until the display
shows
SET FLASH TIMESET FLASH TIME
SET FLASH TIMESET FLASH TIME
SET FLASH TIME
.
3 Press MENU button to confirm.
4 Press UP or DOWN button to select 100MS
(default), 300MS, or 600MS.
5 Press MENU button to confirm.
6 Press RECALL button to return to standby
mode or wait until the program times out.
SET FLASH
TIME
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677
Calls are charged at Local Call rate.
10
5. Telephone Operation
Ringer volume The Ringer High-Low switch located at the
back of the Base unit allows you to adjust the
volume of the ringer.
- High volume
- Low volume
1 Lift the handset, or press SPEAKERPHONE
button on the Base unit.
ÖCheck for dial tone.
2 Dial the telephone number.
ÖThe display shows the duration of the call in
minutes and seconds.
Using the Pre-dial mode
1 Dial the telephone number.
2 Lift the Handset or press SPEAKERPHONE
button on the Base unit to dial out the
number.
Notes:
When using the Speakerphone, speak clearly
into the Base unit microphone from a distance
of 15 cm (6 in.)
To make a
call
When the phone rings:
Lift the Handset, or press SPEAKERPHONE
button on the Base unit.
ÖThe display shows the duration of the call in
minutes and seconds .
To answer a
call
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677
Binatone Help Line - 0845 345 9677
Calls are charged at Local Call rate.
Table of contents
Other Binatone Telephone manuals
Binatone
Binatone Trend LCD User manual
Binatone
Binatone Trend 3 Executive User manual
Binatone
Binatone LYRIS 110 User manual
Binatone
Binatone Spirit 110 User manual
Binatone
Binatone IDECT X3 User manual
Binatone
Binatone iDECT Freedom Twin User manual
Binatone
Binatone Caprice 670 User manual
Binatone
Binatone CAPRICE CAPRICE 600 User manual
Binatone
Binatone 433 User manual
Binatone
Binatone Caprice 670 User manual
Binatone
Binatone SPIRIT 710 User manual
Binatone
Binatone LYRIS 310 User manual
Binatone
Binatone iDECT M3i User manual
Binatone
Binatone iDECT L1i System User manual
Binatone
Binatone AC2000 User manual
Binatone
Binatone SC2050 User manual
Binatone
Binatone ACTIVE XA2020 User manual
Binatone
Binatone Lyris 710 User manual
Binatone
Binatone 3488 User manual
Binatone
Binatone DSR-3716PA User manual
