BEMIS A06303TWA 000 User manual
Installation and User’s Manual
Personal Wash
Bidet
2
TABLE OF
CONTENTS
Parts...........................................................................................3
Pre-Installation......................................................................4
Installation .............................................................................5
Adjusting the Comfort Stream™..................................10
How to Use Your Bidet....................................................12
Cleaning.................................................................................13
Warranty.................................................................................14
3
Bidet attachment
2 Adjustable
mounting disks
T-Valve connector
with rubber washer
(7/8” x 7/8” x 3/4”)
27.5” Braided Metal
Hose for T-Valve /
Bidet connection
Teflon tape
PARTS
4
PRE-INSTALLATION
Please review prior to starting the installation
Water Supply Line
•Confirm that your current water supply line to the toilet
is a flexible water supply hose
•If it is a rigid pipe, you will need to replace this with a
flexible water supply hose
•Flexible water supply hose needs to be 7/8”
to connect to the T-Valve and 3/8” or 1/2”
dependent on your water supply valve size
Adjustable T-Valve (included)
•The adjustable T-Valve supplied with the bidet mounts
onto the fill valve connection on the underside of the
toilet tank
•DO NOT mount the adjustable T-Valve onto the water
supply valve .
•Teflon Tape is included if you choose to use it.
Remove your current toilet seat when you are
ready to begin the installation
5
INSTALLATION
1. Close the water supply valve
to the toilet. Flush the toilet to
minimize the water in the tank.
Place a towel on the floor to
absorb any water.
2. Disconnect the water hose from
the fill valve connection under the
tank of the toilet
3. Confirm that the rubber washer
is in the T-Valve. Connect
the adjustable T-Valve to the
underside of the toilet tank.
Turn the water control handle
downwards. This shuts off the
water to the Bidet attachment.
4. Attach the water supply
hose (attached to the water shut
off valve) to the bottom
of the T-Valve.
6
INSTALLATION (cont.)
5. Connect the metal hose supplied
with the Bidet to the open side of
the T-Valve.
6. Straighten the hinges on your
Clean Shield seat as shown in the
diagram.
7. Place the bidet on the
toilet. While holding the
bidet in place, place the circular
mounting disks into
the bidet attachment.
8. Holding the attachment as far
back in the bowl as possible, align
the slots in the circular mounting
disks so you can see the seat
mounting holes on the toilet. (The
slots should be mirrored to each
other)
7
9. While holding down the bidet attachment with one hand, pick up
the Clean Shield seat, align the bolts to the mounting holes and push the seat
downward through the slots in the circular mounting disks so the bolts enter
the seat mounting holes on the toilet. Pushing downward and holding the
seat in place, lightly handtighten the Snap 2 Secure nuts
10. Prior to final tightening, center the bidet attachment. Slide the bidet
attachment as far to the back of the bowl as possible. Align the circular
mounting disks so the angle of the slots are mirrored. (see diagrams 10A
and 10B) Confirm that the bidet attachment is centered by checking that the
hinge bases are on the same location on the bidet attachment (see diagram
10C)
*For best results, the attachment should be back as far as possible and the
slot angles should be mirror images.
10A 10B 10C
8
INSTALLATION (cont.)
11. Holding the bidet attachment in
place, tighten the Snap 2 Secure
nuts until the installation head
snaps off.
12. Connect the hose from
the T-Valve to the Bidet
Attachment and tighten.
13. Confirm that the handle
on the bidet is turned to the off
position (This prevents the bidet
from squirting when the
water is turned on)
14. Slowly turn the water
supply valve open.
Check for leaks as the
valve opens. If leak occurs, turn
off the water supply and tighten
the connection properly.
9
Notes
10
ADJUSTING the
COMFORT STREAM™
1. Start with the T-Valve knob in the
off position… pointing straight
down (see photo)
2. Turn the knob a small amount to
open the valve (see photo)
Turning the knob small amounts will
help you find your preferred stream
strength more quickly
Table of contents
Other BEMIS Bathroom Fixture manuals
BEMIS
BEMIS bioBidet BB-2000 Operating and safety instructions
BEMIS
BEMIS Assurance R85320H20 ARM User manual
BEMIS
BEMIS BioBidet BB-270 User manual
BEMIS
BEMIS Bio Bidet LW-1000 User manual
BEMIS
BEMIS Plastic Pro UK004 User manual
BEMIS
BEMIS NextStep User manual
BEMIS
BEMIS bioBidet BB-2000 User manual
BEMIS
BEMIS UK062 User manual
BEMIS
BEMIS bioBidel Slimedge User manual
BEMIS
BEMIS bioBedet BB1000 User manual
