Belkin F7D1301 V1 User manual
23525_8820-00370_F7D1301 v1_Basic Router_0208 change
ROUTER
USER MANUAL
F7D1301 V1 v1
TABLE OF CONTENTS
Getting Started
What’s in the Box
Initial Setup
Advanced Tools & Settings
The Belkin Router Manager
Manual Setup Using Your Browser
Adding Computers to Your Network
Getting to Know Your Router
Front Panel
Back Panel
Technical Details
Technical Features
System Requirements
Troubleshooting, Support, and Warranty
Troubleshooting
Technical Support
Belkin International, Inc., Limited 2-Year Product Warranty
Regulatory Information
FCC Statement
23525_8820-00370_F7D1301 v1_Basic Router_0208 change
Getting Started
What’s in the Box
Basic Wireless Router
Ethernet cable (attached to router)
Power supply (attached to router)
Network information card (attached to router)
Belkin Setup C with User Manual
Initial Setup
Where to Place Your Router
For the best results, place the Router next to your modem in an
open location away from large metal objects and magnets such as
those found in speakers. Raising the Router above floor level can
improve the strength of your wireless signal.
How to Set It Up
[R B SIC/SURF SETUP DI GR M basicsurf setup.ai]
1) Connect your Router’s Ethernet cable to your modem’s
Ethernet port (on the back of your modem). This port might
be labeled differently on your particular modem. If you are
adding a Router for the first time, this port may be connected
to your computer by an Ethernet cable. It is OK to disconnect
your computer and plug the Router into the modem instead.
2) Plug the Router’s power supply into a wall outlet.
3) Put the CD into your computer. If the CD doesn’t open
automatically, please browse to your CD drive and double-
click on the Belkin Setup CD icon.
[SCREENSHOT OF SETUP MENU setup menu.png]
4) Click the Setup icon on the CD menu.
23525_8820-00370_F7D1301 v1_Basic Router_0208 change
[SCREENSHOT OF NETWORK INFO C RD SCREEN setup
netinfo card.png]
5) fter a brief installation, the setup software will ask you for
the network name and password from the network
information card that is attached to your Router. Store the
card under the base of your Router for future reference.
[SCREENSHOT OF SUCCESS setup success.png]
6) progress screen will appear while additional software is
installed. This may take a few minutes to complete. Once
finished, a “Success” message will appear indicating that you
are connected to the Internet via your new Belkin Router.
During setup you may be asked for additional information.
You may need to enter a username and password provided by your ISP.
This username and password is likely to be found on materials that came
from your ISP when you signed up for service. If necessary, you may need
to contact your ISP to retrieve your username and password.
If you have a static IP address, you may need to enter additional
information also provided by your ISP.
If your computer doesn’t have a wireless adapter, or the setup software is
unable to control it, you may be asked to connect your computer to the
outer with a network cable.
Advanced Tools & Settings
[SCREENSHOT OF A VANCE MENU setup advanced2.png]
After the initial setup is complete, you have the option to change settings like
your network name, security type, and password. To make these changes and
others, click on the Advanced Tools icon at the C Setup menu and select one
of the following settings that you would like to change:
Network Name & Security
Personalize your network name (SSID), password, and strength of
wireless security.
23525_8820-00370_F7D1301 v1_Basic Router_0208 change
Internet Service Provider & Login Settings
Have you moved or changed Internet Service Providers? If you’d like to
change these settings without running through the setup process again,
this is the place.
The Belkin Router Manager
[BASIC/ SCREENSHOT OF TRAY APP MENU (TB )]
The Belkin Router Manager appears in your system tray (Windows) or menu bar
(Mac). Its icon indicates the current status of your Router and also allows you to
access your Router’s settings to make changes. It also provides quick access to
software that came bundled with your Router.
To access the Router settings, click on the icon and select from the menu that
appears.
The status of your Router is shown by the Belkin Router Manager icon, which
closely mimics the light on the front of the Router.
Green: You are connected to your Belkin Router and it is connected to the Internet.
Amber: You are connected to your Belkin Router, but it is not connected to the
Internet.
23525_8820-00370_F7D1301 v1_Basic Router_0208 change
Manual Setup Using Your Bro ser
[ZOOME SCREENSHOT OF A RESS BAR address bar.png]
In your browser, type “http://router” (you do not need to type in anything else
such as “www”). Then press the Enter key. If you’re still having trouble running
the manual setup option, type “192.168.2.1” in your browser (you do not need
to type in anything else such as “http://” or “www”). Then press the Enter key.
Adding Computers to Your Net ork
Wireless devices such as computers, network printers, and gaming systems can
connect to your Router with a few simple steps.
Using the C
1) Put the Setup CD into your computer. If the CD doesn’t open
automatically, browse to your CD drive and open the Belkin
Setup CD icon.
2) Click the Setup icon on the CD menu.
3) fter a brief installation, the setup software will ask you for
the network name and password from the network
information card that came with your Router. This card is
most likely now located underneath the foot of your Router
in the provided card slot.
4) progress screen will appear while additional software is
installed. This may take a few minutes to complete. Once
finished, a “Success” message will appear indicating that you
are connected to the Internet via your new Belkin Router.
Note: The setup software runs only on Windows and Mac OS X
systems.
Manually
If you choose not to use the included Setup CD for adding
additional computers or wireless devices, you can manually add
these items to your network.
1) Locate the wireless-network-connections option on your
computer or wireless device.
23525_8820-00370_F7D1301 v1_Basic Router_0208 change
2) Select your Belkin Router from the list of available networks.
You can identify your Belkin Router by locating the network
name (SSID) from the card located underneath the foot of
your Router.
3) Enter your network password (located on your network
information card).
Your wireless device will take a few moments to connect to
your network. If the connection is not made the first time, try
this process again. If you still have difficulty connecting to
your network after trying this process a few times, see the
“Troubleshooting” section in this manual for help with
connecting to your network.
Note: In some cases you may be prompted to select the
security type. It is printed on the card for your convenience.
Using the WPS Button
1) Start WPS Push Button Connection (WPS PBC) on your
computer or other Wi-Fi device that you would like to
connect wirelessly to your Router. Often there will be a
button for this purpose in software that came with the device,
or a physical “WPS,” “PBC,” or “Security” button on the device
itself.
2) Within two minutes, press the WPS button on your Router.
The WPS light (small light above WPS button) will blink green
while it listens for your Wi-Fi device. Once a connection is
established, the light will turn green and then go out. If a
connection is not established, the light will blink amber. You
may repeat the process to try again.
You can repeat this process for each WPS-enabled device you’d
like to add to your network.
Getting to Know Your Router
Front Panel
23525_8820-00370_F7D1301 v1_Basic Router_0208 change
[ IAGRAM front.ai]
A) Router Status Light
Your Router’s status is shown by the light on the front.
Off: The outer is not plugged into a power source.
Blinking Green: The outer is starting up.
Solid Green: The outer is connected to the Internet.
Blinking Amber: The outer can’t detect the modem. Either the modem is
off, is not plugged into the outer, or is unresponsive.
B) Wi-Fi Protected Setup (WPS) Light and Button
The WPS button on the front of your Router can be used to help
establish a secure connection between your Router and other WPS-
enabled Wi-Fi devices such as computers. To use the WPS feature
on your Router, see “Getting Started > dding Computers to Your
Network > Using the WPS Button”.
The small light near the WPS button shows what is happening
while you are using WPS to establish a connection.
Off: Idle
Blinking Green: The outer is listening for a WPS-enabled computer or
other device.
Solid Green: The outer has made a secure connection with the computer
or other device.
Amber: A connection was not created.
23525_8820-00370_F7D1301 v1_Basic Router_0208 change
Back Panel
[R IAGRAM FOR BASIC AN SURF r_basicsurf_back.ai]
A) Modem (WAN) Connector
Connect your modem to this port using an Ethernet cable.
B) Wired (LAN) Connectors
Connect computers and other wired network devices to these ports
using Ethernet cables.
C) Reset Button
This button is used to restart your Router in rare cases when it
functions incorrectly. Resetting the Router will preserve your
settings. This button may also be used to restore the factory default
settings. Please see the Troubleshooting section for more
information.
) Power Connector
Connect the included power supply to this jack.
Technical Details
Technical Features
Integrated 802.11n Wireless Access Point
The N150 technology enhances your Router
’
s wireless capabilities,
allowing for data transfer speeds of up to 150Mbps across your network.
NAT IP Address Sharing
To save you the cost of adding IP addresses per computer in your house,
your Belkin Router uses Network Address Translation (NAT) technology,
allowing you to share a single IP address across your network.
SPI Firewall
Your Router is equipped with a firewall that will protect your network
from a wide array of common attacks and viruses.
Universal Plug-and-Play (UPnP) Compatibility
The UPnP (Universal Plug-and-Play) feature in your Router offers
seamless operation of voice and video messaging, games, and other
applications that are UPnP-compliant.
Web-Based Advanced User Interface
23525_8820-00370_F7D1301 v1_Basic Router_0208 change
You can easily make changes to your Router
’
s advanced settings through
your web browser. These changes can be made from any computer on your
network.
Belkin Router Monitor
The Belkin Router Monitor application helps you to monitor your
Router
’
s status and change network settings.
Integrated 4-Port 10/100 Switch
Your Router has a built-in, 4-port network switch to allow your wired
computers to share: printers, data, MP3 files, digital photos, and much
more.
System Requirements
Router
Broadband Internet connection such as a cable or DSL modem with RJ45
(Ethernet) connection
At least one computer with an installed network interface adapter
TCP/IP networking protocol installed on each computer
RJ45 Ethernet networking cable
Internet browser
Setup Software
A computer running Windows® XP SP2 or higher, Windows Vista®, or
Windows 7; or Mac OS® X v10.x
Minimum 1GHz processor and 256MB RAM
600MB of free hard-drive space for installation
23525_8820-00370_F7D1301 v1_Basic Router_0208 change
Troubleshooting, Support, and Warranty
Troubleshooting
The Setup C does not automatically start.
If Belkin Setup does not run when you insert the CD-ROM, your
computer may not be configured to open CDs automatically.
If Belkin Setup does not appear within 15 seconds, browse to your
CD-ROM drive and open the “Belkin Setup” icon. lternatively, you
may visit http://router/ and perform the setup manually. Please
see “Manual Setup Using Your Browser” earlier in this manual for
more information.
Belkin Setup cannot find my Router.
If Belkin Setup is not able to communicate with your Router during
the installation process, please check the following items.
1) Make sure that the wireless hardware on your computer is turned
on, if available.
2) Try connecting your computer to one of the four “wired” ports on
the outer with an Ethernet cable.
3) Ensure that the outer is on. The front-panel light should be on.
4) Unplug the outer’s power supply for 10 seconds, then plug it back
in.
5) There may be firewall software on your computer preventing an
outgoing connection. You may choose to temporarily disable this
software before attempting setup.
If Belkin Setup still cannot find the Router, you might choose to do
a manual setup. Refer to “Manually Configuring Network Settings”
in this manual for details.
Belkin Setup cannot connect my Router to the Internet.
If Belkin Setup is not able to connect the Router to the Internet,
please check the following items:
1) Use the troubleshooting suggestions within Belkin Setup.
Table of contents
Other Belkin Network Router manuals
Belkin
Belkin Wireless Gplus Notebook Card User manual
Belkin
Belkin F9K1001V1 User manual
Belkin
Belkin F9K1124 User manual
Belkin
Belkin AC 1600 DB User manual
Belkin
Belkin F1PI242EGAU Reference guide
Belkin
Belkin F5D7233 - Wireless G Travel Router User manual
Belkin
Belkin F5D52314 - Cable/DSL Gateway Router User manual
Belkin
Belkin Surf User manual
Belkin
Belkin F5D7330 User manual
Belkin
Belkin F5D5230 User manual
Belkin
Belkin F1PI242EGAU User manual
Belkin
Belkin F5D7230au4P User manual
Belkin
Belkin F9K1102V3 User manual
Belkin
Belkin TSG-UK-1-001 Reference guide
Belkin
Belkin F5D7230-4 User manual
Belkin
Belkin 802.11g Wireless Ethernet Bridge User manual
Belkin
Belkin F6D4230-4 User manual
Belkin
Belkin F9K1002V5 User manual
Belkin
Belkin F5D5230U4-V1.20.003 Instruction Manual
Belkin
Belkin F5D7231-4P User manual
