Belkin SURF N150 User manual

N15 0 WIRELESS MODEM ROUTER

User Manual

F9J1004v1 8820ed01125uk Rev.A00

ENGLISH

TABLE OF CONTENTS

GETTING STARTED ........................................3

What’s in the Box ............................................. 3

Initial Setup.................................................. 3

How to Set It UP .............................................. 3

Advanced Tools & Settings..................................... 6

Adding Computers to Your Network ............................. 7

GETTING TO KNOW YOUR ROUTER..........................8

Front Panel .................................................. 8

Back Panel .................................................. 9

TECHNICAL DETAILS......................................10

Technical Features .......................................... 10

System Requirements........................................ 11

TROUBLESHOOTING, SUPPORT, AND WARRANTY ...........12

Troubleshooting ............................................. 12

Technical Support ........................................... 15

Warranty ................................................... 16

How to get service? .......................................... 17

REGULATORY INFORMATION ..............................18

Declaration of Conformity with electromagnetic compatibility and

electromagnetic interference .................................. 18

Europe – EU Declaration of Conformity ......................... 19

General Safety Information: ................................... 19

GETTING STARTED

What’s in the Box

N150 Wireless Modem-Router

ADSL cable

Power supply

Ethernet cable

Network information card

Belkin Setup CD with User Manual

Initial Setup

Where to Place Your Router

For the best results, place the Router in an open location

away from large metal objects and magnets such aas those

found in speakers. Raising the Router above floor level

can improve the strength of your wireless signal.

How to Set It UP

1. Connect your Router’s ADSL cable to your phone jack or phone-

jack adapter (microfilter). If you are replacing an existing Router

or gateway, this may require unplugging the existing gateway.

Note: If required by your Internet Service Provider (ISP), plug the included

phone-jack adapter (microfilter) into your wall-mounted phone jack.

Please check with your provider before connecting your Router if you are

unsure whether or not you need to use the included phone-jack adapter.

2. Plug the Router’s power supply into a wall outlet.

3. If your PC has been installed with a wireless adapter,

search for wireless networks on your computer, connect to

the wireless network which matches the ‘’Network Name

(SSID)” on the label on the underside of your router.

GETTING STARTED

4. When prompted, enter the password shown on

the label on the underside of the router.

5. Open the Internet Explorer (IE) browser and enter

http://192.168.2.1. In the Login page displayed, enter

the username admin and password admin.

GETTING STARTED

6. After logining in, you will see the main interface below. Click

Wizard from the main menu on the left. It will guide you through

fast and accurate Internet connection. Click finish to finish, and

now you are connected to the Internet via your new Belkin Router.

7. During setup you may be asked for additional information.

You may need to enter a username and password provided

by your ISP. This username and password is likely to be

found on materials that came from your ISP when you

signed up for service. If necessary, you may need to contact

your ISP to retrieve your username and password.

If you have a static IP address, you may need to enter

additional information also provided by your ISP.

If your PC has been installed with a wired network card, connect

your PC to a LAN interface of the Router using the Ethernet cable.

Configure the TCP/IP properties of your network card to Obtain an

IP address automatically from modem, or set the IP address of the

computer as 192.168.2.X/255.255.255.0. The X is from 2 to 254.

Enter your VCI and VPI information provided by your ISP.

GETTING STARTED

Advanced Tools & Settings

After the initial setup is complete, you have the option to change

settings like your network name, security type, and password.

Network Name & Security

In the main menu, click Wireless > Basic Settings.

You can personalize your Network Name (SSID).

In the main menu, click Wireless > Security. You can change

password and the strength of wireless security.

Adding Computers to Your Network

Wireless devices such as computers, network printers, and gaming

systems can connect to your Router with a few simple steps.

Manual Setup

You can manually add additional computers

or wireless devices to your network.

1. Locate the wireless > network > connections

option on your computer or wireless device.

GETTING STARTED

2. Select your Belkin Router from the list of available networks. You

can identify your Belkin Router by locating the network name

(SSID) from the card located underneath the foot of your Router.

3. Enter your network password (located on

your network information card).

Your wireless device will take a few moments to connect to your

network. If the connection is not made the first time, try this

process again. If you still have difficulty connecting to your network

after trying this process a few times, see the “Troubleshooting”

section in this manual for help with connecting to your network.

Note: In some cases you may be prompted to select the

security type. It is printed on the card for your convenience.

Using the WPS Button

1. Start WPS Push Button Connection (WPS PBC) on your

computer or other Wi-Fi device that you would like to

connect wirelessly to your Router. Often there will be a

button for this purpose in software that came with the

device, or a physical “WPS” button on the device itself.

2. Within two minutes, press the WPS button on your Router.

The WPS indicator will blink green while it listens for your

Wi-Fi device. Once a connection is established, the light will

turn green for about 5 minutes and then go out. If a connection

is not established, the light will blink green for 2 minutes and

30 seconds. You may repeat the process to try again.

You can repeat this process for each WPS-enabled

device you’d like to add to your network.

GETTING TO KNOW YOUR ROUTER

Front Panel

Your Router’s status is shown by the lights on the front panel.

Power Light

Off: The Router is powered off.

Solid Green: Intialization of the Router is successful.

Solid Red: The Router is self-testing, or self-testing is

failed, or software upgrade is under progress.

Modem Light

Solid Green: Connection between the Router and the

physical layer of the office is established.

Slow Blinking Green:No signal is being detected.

Fast Blinking Green: The Router is handshaking

with the physical layer of the office.

Internet Light

Off: The Router is in bridged mode, or no data is transmitted via a WAN port.

Blinking Green: Data is being transmitted in routing mode or bridged mode.

Solid Red: The Internet connection fails after successful

synchronization in routing mode (for example: PPP dial-up is failed).

LAN Light

Off: LAN connection is not created.

Blinking Green: LAN data is being transmitted, or Internet

data is being transmitted in bridged mode.

Solid Green: LAN connection is established and activated.

WLAN Light

Off: WLAN is disabled.

Blinking Green: Wireless data is being transmitted in the WLAN.

Solid Green: WLAN is enabled but no data is transmitted.

Wi-Fi Protected Setup (WPS) Light

Off: Idle

Blinking Green: The Router is listening for a WPS-

enabled computer or other device.

Successful Connection:The WPS light is SOLID GREEN

for 5 minutes and then goes out when the Router has made a

secure connection with the computer or other device.

Failed Connection: The WPS light is BLINKING GREEN for 2

minutes and 30 seconds after the WPS connection fails.

GETTING TO KNOW YOUR ROUTER

Back Panel

WPS Button

This button is used to help establish secure connection between your

Router and other WPS-enabled Wi-Fi devices such as computers.

To use the WPS feature on your Router, see “Getting Started >

Adding Computers to Your Network > Using the WPS Button”.

Modem (WAN) Connector

Connect your Router to a phone jack using a telephone

cord. In some areas, a microfilter might be required.

Wired (LAN) Connectors

Connect computers and other wired network devices

to these ports using Ethernet cables.

Power Connector

Connect the included power supply to this jack.

Reset Button

This button is used to restart your Router in rare cases when it

functions incorrectly. Resetting the Router will preserve your settings.

This button may also be used to restore the factory default settings.

Please see the Troubleshooting section for more information. To

reset the Router, press and hold this button for at least 10 seconds.

TECHNICAL DETAILS

Technical Features

Integrated ADSL2+ Modem

The integrated ADSL2+ modem allows you to connect to

the Internetyou’re your local Internet Service Provider (ISP)

without installing and maintaining a separate DSL modem.

Integrated 802.11n Wireless Access point

The N150 technology enhances your Router’s

wireless capabilities, allowing for data transfer speeds

of up to 150Mbps across your network.

NAT IP Address Sharing

To save you the cost of adding IP address per computer

in your house, our Belkin Router uses Network Address

Translation (NAT) technology, allowing you to share

a single IP address across your network.

SPI Firewall

Your Router is equipped with a firewall that will protect your

network from a wide array of common attacks and viruses.

Universal Plug-and-Play (UPnP) Compatibility

The UPnP (Universal Plug-and-Play) feature in your Router

offers seamless operation of voice and video messaging,

games, and other applications that are UPnP-compliant.

Web-Based Advanced User Interface

You can easily make changes to your Route’s advanced

settings through your web browser. These changes can

be made from any computer on your network.

Integrated 4-Port 10/100 Switch

Your Router has a built-in, 4-port network switch to

allow your wired computers to share: printers, data,

MP3 files, digital photos, and much more.

Other manuals for SURF N150

Table of contents

Other Belkin Modem manuals

Belkin

Belkin F5D7632 User manual

Belkin

Belkin ADSL Modem with Wireless-G Router F5D7632UK4 User manual

Belkin

Belkin 8820-00056EA User manual

Belkin

Belkin F5D9630uk4A User manual

Belkin

Belkin F5D9630-4 User manual

Belkin

Belkin F5D7632uk4A User manual

Belkin

Belkin F7D1401au User manual

Belkin

Belkin F5U302ea User manual

Belkin

Belkin ADSL Modem User manual

Belkin

Belkin F5D7633uk4 User manual

Belkin

Belkin F5D5730au User manual

Belkin

Belkin High Speed ADSL2+ User manual

Belkin

Belkin F5D5630au User manual

Belkin

Belkin F5D7633uk4 User manual

Belkin

Belkin F5D8631-4 User manual

Belkin

Belkin F1PI241ENau User manual

Belkin

Belkin F5D7633uk4A User manual

Belkin

Belkin F1PI210ENau User manual

Belkin

Belkin F5D5630au4 User manual

Belkin

Belkin F9J1005 User manual

Belkin

Belkin F5D7630-4A User manual

Belkin

Belkin F5D7632-4V5 User manual

Belkin

Belkin F5D7632uk4v3000 User manual

Belkin

Belkin F5D9630-4A User manual

Popular Modem manuals by other brands

Davicom

Davicom DM562AP Operation manual

EpiValley

EpiValley TATA indicom SXC-1080 user guide

Zte

Zte WiMAX user manual

Intelimax

Intelimax MA-2060 user manual

SMC Networks

SMC Networks D3CM1604V Administrator's manual

Telstra

Telstra Wi-Fi 4G Advanced Pro X user guide

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 user manual

Samsung

Samsung AceLink SAM-335A user guide

Enfora

Enfora Enabler-G Integration guide

iRZ

iRZ ATM2-232 user guide

Zhone

Zhone 6310 installation instructions

Paradyne

Paradyne Hotwire 7976 installation instructions

US Robotics

US Robotics 3453C datasheet

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... user manual

Zte

Zte MF823 user guide

Four-Faith

Four-Faith F1403 user manual

Sierra Wireless

Sierra Wireless AIRLINK MP595W user guide

Gemtek

Gemtek WiMAX WIXFBR-103 user manual