Beko WTK82011W User manual

Washing Machine

User Manual

WTK82011W - WTK82041W - WTL82051W

2820528765_EN/ 25-06-20.(15:17)

Document Number :

9 / EN

Washng Machne / User Manual

Your product

4.1 Overview

1- Power cable

2- Top panel

3- Control panel

4- Drain hose

5- Loading door

6- Filter cap

7- Adjustable feet

8- Detergent drawer

10 / EN

Washng Machne / User Manual

4.2 Package Contents

11 12

abc

9- Power cable

10- Drain hose

11- Transportation safety bolts*

12- Mains water inlet hose (One of the following filter types is used for the mains hose

connection.)

a- Electronic water shut-off

b- Mechanical water shut-off

c- Standard

13- Liquid detergent container**

14- User Manual

15- Blind plug***

16- Plastic plug group

* Number of transportation safety bolts may change depending on the model of your product.

** This may be supplied with the machine depending on the model of your product.

*** It will be supplied if your product has double water inlet.

Figures in this manual are schematic and may not match the product exactly.

11 / EN

Washng Machne / User Manual

4.3 Technical specifications

SUPPLIER’S NAME MODEL IDENTIFIER

(*)

The model information as stored in the product

database can be reached by entering following

website and searching for your model identifier (*)

found on energy label.

https://eprel.ec.europa.eu/

Supplier name or trademark Beko

Model name WTK82011W WTK82041W WTL82051W

7178682100 7178682300 7178682200

Rated capacity (kg) 8

Maximum spin speed (rpm) 1200

Built-in No

Height (cm) 84

Width (cm) 60

Depth (cm) 59

Single Water inlet / Double Water inlet • / -

• Available

Electrical input (V/Hz) 230 V / 50Hz

Total current (A) 10

Total power (W) 2200

Main model code 9211

12 / EN

Washng Machne / User Manual

4.4 Installation

• Preparation of the location and electrical, tap water and waste water installations at the

place of installation is the customer's responsibility.

• Make sure that the water inlet and discharge hoses as well as the power cable are not

folded, pinched or crushed while pushing the product into its place after installation or

cleaning procedures.

• The manufacturer shall not be held liable for damages that may arise from procedures

carried out by unauthorised persons.

• Prior to installation, visually check if the product has any defects on it. If so, do not have

it installed. Damaged products cause risks for your safety.

4.4.1 Approprate nstallaton locaton

• Place the product on a hard and level floor. Do not put it onto a carpet with high pile or

other similar surfaces.

• If the washing machine and dryer are placed on top of each other, their total weight –

when loaded– amounts to 180 kilograms. Place the products on a solid and flat floor that

has sufficient load carrying capacity!

• Do not place the product on the power cable.

• Do not install the product in environments where the temperature falls below 0 ºC.

• Leaving a gap at the sides of the machine is suggested to reduce vibration and noise

• On a raised floor, do not place the product next to the edge or on a platform.

• Do not place heat sources such as Hobs, Irons, Ovens, etc. on the washing machine and

do not use them on the product.

4.4.2 Removng packagng renforcement

Tilt the machine backwards to remove the packaging

reinforcement. Remove the packaging reinforcement that is

attached to the ribbon. Do not attempt this operation alone,

get help.

13 / EN

Washng Machne / User Manual

4.4.3 Removng the transportaton locks

1 Loose all bolts with an appropriate wrench until they turn freely.

2 Remove the transport safety bolts by rocking them slightly.

3 Insert the plastic covers from the bag containing the user manual into the openings on

the rear panel.

ACAUTION:

Remove the transportation safety bolts before operating the washing

machine! Otherwise, the product will be damaged.

Keep the transportation safety bolts in a safe place to reuse when the washing machine

needs to be moved again in the future.

Install the transport safety bolts in the reverse order of the disassembly procedure.

Never move the product without the transportation safety bolts properly fixed in place!

4.4.4 Connectng the water supply

It is necessary to have 10 – 80 litres of water flowing from the fully open tap in one minute

to have your machine run smoothly. Attach a pressure reducing valve if the water pressure is

higher.

ACAUTION:

Models with a single water inlet should not be connected to the hot water tap.

In such a case the laundry will get damaged or the product will switch to protection mode and

will not operate.

1 Tighten the nuts of the hose by hand. Never use a tool when tightening the nuts.

2 When hose connection is completed, check whether there are no leak problems at the

connection points by opening the taps fully. If any leaks occur, turn off the tap and

remove the nut. Retighten the nut carefully after checking the seal. In order to prevent

the water leaks and resultant damages, keep the taps closed when you do not use the

product.

14 / EN

Washng Machne / User Manual

4.4.5 Connectng the dran hose to the dran

• Attach the end of the drain hose directly to the waste water drain, lavatory or bathtub.

ACAUTION:

Your drain house will be flooded if the hose comes out of its housing during

water discharge. Moreover, there is risk of scalding due to high washing temperatures! In

order to prevent such situations and make sure that the machine performs water intake and

discharge processes without any problem, fix the drain hose securely.

• Connect the drain hose to a minimum height of 40 cm and a maximum height of 100 cm.

• In case the drain hose is elevated after laying it on the floor level or close to the ground

(less than 40 cm above the ground), water discharge becomes more difficult and the

laundry may come out excessively wet. Therefore, follow the heights described in the

figure.

40 cm

100 cm

• To prevent the waste water siphoning back into the machine again and to ensure easy

drainage, do not immerse the end of the hose into the waste water or do not insert it

into the drain for more than 15 cm. If it is too long, cut it short.

• The end of the hose should not be bent, it should not be stepped on and the hose must

not be pinched between the drain and the machine.

• If the length of the hose is too short, add an original extension hose. Length of the hose

may not be longer than 3.2 m. To avoid water leak failures, the connection between

the extension hose and the drain hose of the product must be fitted well with an

appropriate clamp as not to come off and/or leak.

4.4.6 Adjustng the feet

ACAUTION:

In order to ensure that the product operates more silently and vibration-free,

it must stand level and balanced on its feet. Balance the machine by adjusting the feet.

Otherwise, the product may move from its place and cause crushing and vibration problems.

CAUTION:

Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.

1 Loosen the lock nuts on the feet by hand.

2 Adjust the feet until the product stands in a stable and balanced way.

3. Tighten all lock nuts by hand again.

15 / EN

Washng Machne / User Manual

4.4.7 Electrcal connecton

Connect the product to a grounded outlet protected by a 13 A fuse. Our company shall not

be liable for any damages that will arise when the product is used without grounding in

accordance with the local regulations.

• Connection must comply with national regulations.

• The wiring for the electrical outlet circuit must be sufficient to meet the appliance

requirements. Use of a Groud Fault Circuit Interrupter (GFCI) is recommended.

• Power cable plug must be within easy reach after installation.

• If the current value of the fuse or breaker in the house is less than 13 Amps, have a

qualified electrician install a 13 Amp fuse.

• The voltage specified in the “Technical specifications” section must be equal to your

mains voltage.

• Do not make connections via extension cables or multi-plugs.

BWARNING:

Damaged power cables must be replaced by Authorised Service Agents.

Electrical requirements

Before you insert the plug into the wall socket make sure that the voltage and the

frequency shown in the rating label corresponds to your electricity supply.

We recommend that this appliance be connected to the mains supply via a suitable

switched and fused socket in a readily accessible position.

Should the mains lead of the appliance become damaged or need replacing at any time, it

must be replaced by a special purpose made mains lead which can only be obtained from

an Authorised Service Agent.

BWARNING:

This appliance must be earthed

If the fitted moulded plug is not suitable for your socket, then the plug should be cut off

and an appropriate plug fitted.

Destroy the old plug, a cut off plug with a bare cord could cause a shock hazard if inserted

into a socket elsewhere in the house.

The moulded plug on this appliance incorporates a 13A fuse. Should the fuse need to be

replaced an ASTA approved BS1362 fuse of the same rating must be used. Do not forget to

refit the fuse cover. In the event of losing the fuse cover, the plug must not be used until a

replacement fuse cover has been fitted. Colour of the replacement fuse cover must be the

same colour as that visible on the pin face of the plug. Fuse covers are available from any

good electrical store.

16 / EN

Washng Machne / User Manual

Important

Fitting a different plug

As the colours of the wires in the mains lead of this

appliance may not correspond with the coloured markings

identifying the terminals on your plug, proceed as follows:

1 Connect the green - yellow or green (earth) wire to the

terminal in the plug marked ‘E’ or with the symbol or

coloured green and yellow or green.

2 Connect the blue (neutral) wire to the terminal in the

plug marked ‘N’ or coloured black.

3 Connect the brown (live) wire to the terminal in the plug

marked ‘L’ or coloured red.

With the alternative plugs a 13A fuse must be fitted either

in the plug or adaptor or in the main fuse box. If in doubt

contact a qualified electrician.

Transportation of the product

1. Unplug the product before transporting it.

2. Remove water drain and water supply connections.

3. Drain all water that has remained in the product.

4.Install transportation safety bolts in the reverse order of removal procedure.

Never move the product without the transportation safety bolts properly fixed in place!

AWARNING:

Packaging materials are dangerous to children. Keep packaging materials in a

safe place away from reach of the children.

4.4.8 Intal use

Before starting to use the product make sure that the

preparations are made which are in line with the “Important

Safety and Environment Instructions” and the instructions in

the “Installation” section.

To prepare the product for washing laundry, first perform

a Drum Cleaning programme. If this is not available in your

machine, apply the method which is described in the section

4.7.2.

Use an anti-limescale suitable for the washing machines.

Some water might have remained in the product due to the quality control processes in

production. It is not harmful for the product.

17 / EN

Washng Machne / User Manual

4.5 Preparation

4.5.1 Sortng the laundry

* Sort laundry according to type of fabric, colour, and degree of soiling and allowable

water temperature.

* Always obey the instructions given on the garment tags.

LAUNDRY WASH SYMBOLS

Symbols for

washing on

machine

Normal wash

No Iron

Sensitive-

Delicate

wash

Hand wash

Not washable

No Spin

WASH Water

temperatures

Maximum 950C700C600C500C400C300C

Symbol(s)   

  

 

     

Drying

symbols Suitable for

dryer No ironing Sensitive /

delicate dry

Do not dry

with dryer

Do not dry Do not

dry-

clean

DRYING

Drying settings

At any temperature

At high temperature

At medium

temperature

At low temperature

Without heating

Hang to dry

Lay to dry

Hang wet to dry

Lay in shadow

to dry

Dry-cleanable

Iron

IRON Dry or steam

Iron at high

temperature

Iron at medium

temperature

Iron at low

temperature

No ironing

Iron without

steam

Maximum temperature 200 0C150 0C110 0C

All bleaches are allowed

Bleach (sodium

hypochlorite)

can be used

Bleach is not

allowed

Only bleaches without

chlorine are allowed

BLEACH

Other manuals for WTK82011W

Table of contents

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide

Samsung

Samsung WF16J9800K Series user manual