Barco UDX Series User manual
ENABLING BRIGHT OUTCOMES
Installation manual
UDX Multifunctional Frame
Registered office: Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
www.barco.com/en/support
www.barco.com
Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
www.barco.com/en/support
www.barco.com
Changes
Barco provides this manual 'as is' without warranty of any kind, either expressed or implied, including but not
limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make
improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time
without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made
to the information in this publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the
secured Barco web site https://www.barco.com/en/signin.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be
recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.
Disposal Information
Waste Electrical and Electronic Equipment
This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste
from electrical and electronic equipment, this product must not be disposed of with other municipal waste.
Please dispose of your waste equipment by handing it over to a designated collection point for the recycling of
waste electrical and electronic equipment. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material resources.
For more information about recycling of this product, please contact your local city office or your municipal
waste disposal service.
For details, please visit the Barco website at: http://www.barco.com/AboutBarco/weee
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of
guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during
transport, as well as for material and manufacturing faults Barco must be informed immediately in writing of
any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on
the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of
complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate
period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the
purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for
direct or indirect damage, and also damage attributed to the operation of software as well as to other services
provided by Barco, being a component of the system or independent service, will be deemed invalid provided
the damage is not proven to be attributed to the absence of properties guaranteed in writing or due to the
intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the
goods are handled incorrectly, in particular if the systems are operated incorrectly or if, after the transfer of
risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the
purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are
attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear
as well as normal maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in this manual
must be complied with by the customer.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights
of their respective holders. All brand and product names mentioned in this manual serve as comments or
examples and are not to be understood as advertising for the products or their manufacturers.
5
Purpose of the UDX series multifunctional frame
The UDX series multifunctional frame is exclusively designed for the Barco UDX projectors and can thus not
be used on any other equipment.
Overview
•Safety
•Introduction
•Before assembling the frame
•Assembling the frame
•Installing the projector onto the multifunctional frame
•Stacking multiple projectors using the multifunctional frame
•Suspending the projector from a truss
•Skewing the projector
•Tilting the projector
•Rotating the projector
•Dimensions
R5906124 /05 UDX Multifunctional Frame
UDX series
multifunctional
frame 1
R5906124 /05 UDX Multifunctional Frame6
1.1 Safety
About this chapter
Read this chapter attentively. It contains important information to prevent damage to the rigging frame. Ensure
that you understand and follow all safety instructions mentioned in this chapter before installing the rigging
frame. After this chapter, additional “warnings”and “cautions”are given depending on the installation
procedure. Read and follow these “warnings”and “cautions”as well.
Installation personnel
This assembly of the frame and installation of the projector must be performed by authorized and qualified
technical personnel only.
Single assembly only
You can only assemble the rigging frame one single time. While you can remove and install other F90
projectors into the frame and it is allowed to replace safety cables, it is not allowed to disassemble the rigging
frame itself.
Expiry date provided adhesive
Make sure to check the expiry date of the adhesive, provided with the rigging frame. Make sure the adhesive
(high strength threadlocker) is not expired.
If expired, makes sure to get new adhesive of similar or higher strength than the one provided in the kit.
Securing all screws and stacking pins
Make sure that the thread of the screws and the stacking pins are provided with the necessary amount of
adhesive.
CAUTION: Make sure that all the screws are sufficiently tightened. Respect the torque required to
tighten all screws.
Forgetting or neglecting to do this may result in an unsafe rigging frame.
CAUTION: When the safety cables have undergone a heavy shock, invisible damage may have
occurred to the safety cables. In this case the safety cables must be replaced.
Maximum stacking and hanging
UDX projectors can be stacked on top of each other on a flat surface, or suspended from a truss using the
multifunctional frame.
Keep the following in mind:
•It is allowed to stack maximum three projectors.
•It is allowed to suspend maximum two projectors.
Transportation of the frame
Never transport the multifunctional frame in portrait position with a projector mounted. Failure to do so can
cause damage the multifunctional frame. Refer to Image 1-1 for a bad and good example of transportation.
UDX series multifunctional frame
R5906124 /05 UDX Multifunctional Frame 7
Image 1-1: Transportation method of the frame
This limitation only counts for transportation of a rigging frame with projector mounted. You can
still install the projector in portrait position while in the rigging frame.
1.2 Introduction
Functionality
An UDX projector mounted in the multifunctional frame makes the projector more rugged and handy.
The multifunctional frame makes it possible to stack multiple projectors. This can be useful for a dual
projection 3D system. In the multifunctional frame, the projector can be rotated around x, y and z axis in order
to obtain a seamless adjustment.
Furthermore, the multifunctional frame can be used to suspend the projector from a truss. This can be done
either in a upright or upside down position.
Content of the kit
Content Pieces
Bottom frame 1
Top frame 1
Vertical profile 4
Rigging screw 8
Side bracket 1
Hex screw with socket head M8 x 20 7
Hex screw with socket head M8 x 45 4
Top stacking pin 4
Small mounting plates 2
Bottom stacking pin 4
Locking pins 4
Set screw M6 8
Orientation rod + nut M3 3
Hex screw with socket head M8 x 30 6
Spring washer M8 6
Plain washer M8 6
High strength threadlocker 1
Necessary tools
•Torque Wrench with high 17 mm hex socket
•Torque Wrench with long 6 mm Allen socket
•Allen wrench 6 mm
•Allen wrench 3 mm
UDX series multifunctional frame
R5906124 /05 UDX Multifunctional Frame8
The high 17 mm hex socket is not a common type of socket. Make sure you have this at your
disposal before assembling the frame.
Parts identification
56
4
1
9
10
3
11
8
2
12
12
7
Image 1-2
1Multifunctional frame (rear side)
2Side bracket
3Projector supporting structure
4Rotate adjustment knob
5Tilt adjustment knob
6Skew adjustment knob
7Projector mounting holes
8Stacking pin
9Orientation rod + nut
10 Locking pin
11 Safety cable (pre-mounted)
12 Small mounting plate
1.3 Before assembling the frame
Packaging
Be careful not to remove all of the cardboard when removing the rigging frame parts from the packaging. You
will need the following parts when trying to place the UDX projector into the rigging frame.
UDX series multifunctional frame
R5906124 /05 UDX Multifunctional Frame 9
1
Image 1-3
1Part of package to be used to insert projector in rigging frame.
1.4 Assembling the frame
Required tools
•Torque wrench with large 17 mm hex socket
•Allen wrench 3 mm
•Allen wrench 6 mm
•High strength threadlocker (e.g. Loctite 262)
Required parts
•Bottom Frame
•Top Frame
•Vertical profile (x4)
•Rigging screw (x8)
•Support frame
•Hex screw with socket head M8x20 (x7)
•Hex screw with socket head M8x45 (x4)
•Top stacking pin (x4)
•Bottom stacking pin (x4)
•Set screw M6 (x8)
•Orientation rod + nut M3
How to assemble the rigging frame?
1. Lay out the bottom frame as illustrated.
UDX series multifunctional frame
R5906124 /05 UDX Multifunctional Frame10
Image 1-4
2. Assemble the vertical frames onto the bottom frame as illustrated. Use the rigging screws to tighten them
together.
Caution: Use high strength threadlocker on the rigging screws thread. Tighten the rigging screws with
a torque of 40 Nm.
40Nm
Image 1-5
3. Place the top frame onto the rest of the rigging frame. Make sure that the two side frame brackets are
positioned on the same side and opposite of each other (Image 1-6). If this is not possible due to mechanical
error, contact Barco.
Image 1-6
4. Fixate the top frame onto the rest of the rigging frame. Use the rigging screws to tighten the two together.
Caution: Use high strength threadlocker on the rigging screws thread. Tighten the rigging screws with
a torque of 40 Nm.
UDX series multifunctional frame
Other manuals for UDX Series
4
Table of contents
Other Barco Projector manuals
Barco
Barco iCon H600 User manual
Barco
Barco F35 User manual
Barco
Barco fD70-DL User manual
Barco
Barco PGWX-62L(-K) User manual
Barco
Barco BarcoData 1209S User manual
Barco
Barco OV-501 User manual
Barco
Barco R9001070 User manual
Barco
Barco CTHD-61B User manual
Barco
Barco Graphics 9200 User manual
Barco
Barco RLM H5 User manual
Barco
Barco iQ (PRO) G350 User manual
Barco
Barco HDF W22 User manual
Barco
Barco Cine 5 User manual
Barco
Barco R9001320 User manual
Barco
Barco OV-515 User manual
Barco
Barco DP K-32B Series Operating manual
Barco
Barco FS35 Installation and operating instructions
Barco
Barco BARCODATA 2100 User manual
Barco
Barco RLM-W14 User manual
Barco
Barco R9000893 User manual
